Download PDF - Gear Technology magazine

More documents

Recommendations

Info

66 GEARTECHNOLOGY March/April 2010 www.geartechnology.com
E V E N T S SHOT PEENING UP CLOSE AND PERSONAL (courtesy Electronics Inc.) At the beginning of Electronics Inc’s. (EI) shot peening workshops, Jack Champaigne, the company’s president, gives opening remarks where he tells attendees that at anytime they have feedback, they should write it down on a thousand dollar bill and submit it to him. Also known as the publisher of The Shotpeener, the well-humored Champaigne and his staff conduct shot peening/blast cleaning workshops and on-site training programs worldwide. They are attended by a range of specialists including product design engineers, machine operators, foremen, supervisors and maintenance and quality engineers. The next workshop takes place in Toronto, Canada, spanning two days of intensive instruction on all aspects of the metal finishing process. Since the workshop is aimed toward a broad audience of all levels, covering the entire scope of shot peening education in two days seems like it could be challenge, but the EI education division staff have carefully organized the workshops and conducted many of them in the past. “We run four classrooms simultaneously because there are so many topics,” Champaigne says. “Once you get over 30 students, it gets difficult to carry on. Typically we might have 40 to 50 topics, and you need 40 instructors.” For these reasons, enrollment is limited. “We can count on a minimum of 20 and a maximum of 40 attendees to a one- or two-day event,” Champaigne says. Topics attendees will learn about include air blast machine design, air blast machine maintenance, advanced intensity, applications, benefits and equipment, basic intensity, basics of media, an introduction to shot peening, peening coverage, rotary-flap peening, saturation curve practice, wheel blast machine design and wheel blast machine maintenance. continued www.geartechnology.com March/April 2010 GEARTECHNOLOGY 67
Page 1 and 2:
March/April 2010 GEARTECHNOLOGY ®
Page 3 and 4:
www.geartechnology.com March/April
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
stock.xchng - Water Cayman Islands
Page 13 and 14:
Page 15 and 16:
this approach is the high cost of t
Page 17 and 18: P R O D U C T N E W S high speed st
Page 19 and 20: P R O D U C T N E W S and shaping,
Page 21 and 22: P R O D U C T N E W S The 280C oper
Page 23 and 24: P R O D U C T N E W S DTR manufactu
Page 25 and 26: P R O D U C T N E W S tion, scale r
Page 27 and 28: P R O D U C T N E W S included as p
Page 29 and 30: P R O D U C T N E W S Grob Systems
Page 31 and 32: P R O D U C T N E W S Mobile Induct
Page 33 and 34: Vacuum carburizing offers shorter c
Page 35 and 36: Thomas says. Jones says from an ind
Page 37 and 38: tive for larger, heavier loads with
Page 39 and 40: Hybrid Economy, NASCAR Performance
Page 41 and 42: can also allow you to reduce the si
Page 43: “Finding products that fill a nic
Page 47 and 48: New Developments in Gear Hobbing Dr
Page 49 and 50: unloading of the workpiece, etc.) a
Page 51 and 52: setup sheets provided by the tool s
Page 53 and 54: as the generating flats—can be se
Page 55 and 56: www.geartechnology.com March/April
Page 57 and 58: tools employed. These are Coniflex,
Page 59 and 60: are given in Figure. 7. The ease-of
Page 61 and 62: High-Temperature Testing of Stanyl
Page 63 and 64: above the glass transition temperat
Page 65 and 66: etween tensile bar fatigue testing
Page 67: is only the case if the failure mod
Page 71 and 72: www.geartechnology.com March/April
Page 73 and 74: N E W S SME INVESTS IN MANUFACTURIN
Page 75 and 76: “Adding the Leader MultiChuck MMY
Page 77 and 78: Inductoheat RECEIVES ISO 9001:2008
Page 79 and 80: Green or Sustainable Manufacturing
Page 81 and 82: Continued from page 84 injection mo
Page 83 and 84: A D V E R T I S E R S i n d e x Use
Page 85 and 86: HELP WANTED APPLICATION ENGINEER Co
Page 87: From the Producers of 80" Straight
show all

Download PDF - Gear Technology magazine

Create successful ePaper yourself

Delete template?

Save as template?