ISPSoft User Manual

More documents

Recommendations

Info

Chapter 2 Starting and Setting Additional remark AH500 series CPU modules are quipped with USB ports, serial ports, and Ethernet ports. Only AHCPU5xx-EN series CPU modules are equipped with Ethernet port. Besides, the serial ports and the Ethernet ports on AH500 series CPU modules can be set by HWCONIFG in ISPSoft. Please refer to section 3.3.3 and section 3.3.4 for more information. Compared with the serial port and the Ethernet port on an AH500 series CPU module, it is more convenient to connect the USB port on the AH500 series CPU module to a computer. If users want to connect a new CPU module to a computer, they can connect the CPU module to the computer with a USB cable, set the serial port and the Ethernet port on the CPU module through HWCONFIG in ISPSoft, and then download the communication parameters for the serial port and the Ethernet port. The default values of the communication parameters for the serial port and the Ethernet port on an AH500 series CPU module are as follows. • Serial port Communication port Communication parameter COM 1 COM 2 Connection type RS232 RS232 Transmission mode ASCII ASCII Communication speed (Baud rate) 9600 9600 Data length 7 7 Parity bit Even Even Stop bit 1 1 Station address 1 3 • Ethernet Communication parameter Parameter value IP address assignment Static IP address 192.168.1.1 Subnet mask 255.255.255.0 Gateway address 192.168.1.1 2-49
ISPSoft User Manual 2.4.8 Practical Connection Test After users complete the steps above, they can check whether a computer communicates with a PLC normally by means of a simple test. Users have to make sure of the items below before a PLC communicates with a computer. (a) The users have to make sure that COMMGR has been started normally, and the status of a driver which will be specified is START. (b) The users have to make sure that the driver which will be specified is set correctly. If the connection type that the driver uses is RS232, the users have to make sure that the communication protocol for exchanging data through the driver is the same as the communication protocol for exchanging data through a communication port on the PLC. (c) The users have to make sure that a communication port used, e.g. a network interface card in the computer, a hub, or a serial port, is in a normal state. (d) The users have to make sure that the driver, the station address, and the IP address which are specified in the Communication Setting window are correct. If an IP address is specified, the users have to check whether the IP address of the PLC is the same as the IP address specified. (e) The users have to make sure that the PLC is correctly connected to the computer through a communication cable, power is supplied to the PLC, and the PLC operates normally. After the users make sure of the items above, they can click System Information on the PLC menu in ISPSoft. ISPSoft will retrieve related information from the PLC. If the computer communicates with the PLC normally, the System Information window will appear, and the related information retrieved from the PLC will be displayed in the window. 2-50
Page 2 and 3:
ISPSoft User Manual Preface ISPSoft
Page 4 and 5:
Chapter 1 Introduction of the Softw
Page 6 and 7:
Page 8 and 9:
Page 10 and 11:
Page 12 and 13: Chapter 1 Introduction of the Softw
Page 14 and 15: Chapter 2 Starting and Setting Tabl
Page 16 and 17: Chapter 2 Starting and Setting Afte
Page 18 and 19: Chapter 2 Starting and Setting Win
Page 20 and 21: Chapter 2 Starting and Setting •
Page 24 and 25: Chapter 2 Starting and Setting they
Page 28 and 29: Chapter 2 Starting and Setting *1.
Page 30 and 31: Chapter 2 Starting and Setting User
Page 32 and 33: Chapter 2 Starting and Setting File
Page 40 and 41: Chapter 2 Starting and Setting In t
Page 48 and 49: Chapter 2 Starting and Setting *. I
Page 52 and 53: Chapter 2 Starting and Setting ‣
Page 54 and 55: Chapter 2 Starting and Setting 2.4.
Page 56 and 57: Chapter 2 Starting and Setting Numb
Page 58 and 59: Chapter 2 Starting and Setting they
Page 60 and 61: Chapter 2 Starting and Setting (5)
Page 64 and 65: Chapter 3 Configuring and Setting a
Page 66 and 67: ISPSoft User Manual By means of the
Page 68 and 69: ISPSoft User Manual (6) If the user
Page 70 and 71: ISPSoft User Manual 3.2 Hardware Co
Page 72 and 73: ISPSoft User Manual All hardware av
Page 74 and 75: ISPSoft User Manual • Method 3 (1
Page 76 and 77: ISPSoft User Manual • AH16AM10N-5
Page 78 and 79: ISPSoft User Manual *. Please refer
Page 80 and 81: ISPSoft User Manual 3.2.2.4 Deletin
Page 82 and 83: ISPSoft User Manual 3.2.2.6 Searchi
Page 84 and 85: ISPSoft User Manual *. If the Repla
Page 86 and 87: ISPSoft User Manual There are two w
Page 88 and 89: ISPSoft User Manual • Method 2 (1
Page 90 and 91: ISPSoft User Manual *. An extension
Page 92 and 93: ISPSoft User Manual 3.2.2.12 Replac
Page 94 and 95: ISPSoft User Manual system configur
Page 96 and 97: ISPSoft User Manual 3.3 Setting the
Page 98 and 99: ISPSoft User Manual Users can ident
Page 100 and 101: ISPSoft User Manual • Enable Remo
Page 102 and 103: ISPSoft User Manual value and a min
Page 104 and 105: ISPSoft User Manual If the sending
Page 106 and 107: ISPSoft User Manual • Enable Stat
Page 108 and 109: ISPSoft User Manual After users sel
Page 110 and 111: ISPSoft User Manual every specific
Page 112 and 113:
ISPSoft User Manual (5) After all t
Page 114 and 115:
ISPSoft User Manual The parameters
Page 116 and 117:
ISPSoft User Manual *1. The paramet
Page 118 and 119:
ISPSoft User Manual If users want t
Page 120 and 121:
ISPSoft User Manual There are two t
Page 122 and 123:
ISPSoft User Manual parameter in a
Page 124 and 125:
ISPSoft User Manual *1. DCISoft ver
Page 126 and 127:
ISPSoft User Manual After Export on
Page 128 and 129:
ISPSoft User Manual window will app
Page 130 and 131:
ISPSoft User Manual different from
Page 132 and 133:
ISPSoft User Manual If users right-
Page 134 and 135:
ISPSoft User Manual (2) The present
Page 136 and 137:
ISPSoft User Manual (2) If the time
Page 138 and 139:
Chapter 4 Quick Start Table of Cont
Page 140 and 141:
Chapter 4 Quick Start (2) When in p
Page 142 and 143:
Chapter 4 Quick Start If users want
Page 144 and 145:
Chapter 4 Quick Start After the use
Page 146 and 147:
Chapter 4 Quick Start 4.5.1 Adding
Page 148 and 149:
Chapter 4 Quick Start (2) Click on
Page 150 and 151:
Chapter 4 Quick Start Additional re
Page 152 and 153:
Chapter 4 Quick Start Additional re
Page 154 and 155:
Chapter 4 Quick Start (2) Select ne
Page 156 and 157:
Chapter 4 Quick Start 4.5.7 Basic E
Page 158 and 159:
Chapter 4 Quick Start 4.5.8 Basic E
Page 160 and 161:
Chapter 4 Quick Start *1. The progr
Page 162 and 163:
Chapter 4 Quick Start Automation>Co
Page 164 and 165:
Chapter 4 Quick Start 4.6.2 Downloa
Page 166 and 167:
Chapter 4 Quick Start 4.6.3 Connect
Page 168 and 169:
Chapter 4 Quick Start If users want
Page 170 and 171:
Chapter 4 Quick Start Right-click D
Page 172 and 173:
Chapter 4 Quick Start The program c
Page 174 and 175:
Chapter 5 Program Organization Unit
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Chapter 6 Symbols Table of Contents
Page 220 and 221:
Chapter 6 Symbols • VAR-General s
Page 222 and 223:
Chapter 6 Symbols 6.1.4 Assigning a
Page 224 and 225:
Chapter 6 Symbols Application Examp
Page 226 and 227:
Chapter 6 Symbols • Local symbol
Page 228 and 229:
Chapter 6 Symbols • STRING If the
Page 230 and 231:
Chapter 6 Symbols • Auto-close Di
Page 232 and 233:
Chapter 6 Symbols double quotes, an
Page 234 and 235:
Chapter 6 Symbols *. Before the ini
Page 236 and 237:
Chapter 6 Symbols Select a file whi
Page 238 and 239:
Chapter 6 Symbols Press Alt+ on the
Page 240 and 241:
Chapter 6 Symbols Users can set a d
Page 242 and 243:
Chapter 6 Symbols Double-click RUN_
Page 244 and 245:
Chapter 6 Symbols If users want to
Page 246 and 247:
Chapter 7 Function Block Table of C
Page 248 and 249:
Chapter 7 Function Block 7.1.2 Char
Page 250 and 251:
Chapter 7 Function Block Class VAR_
Page 252 and 253:
Chapter 7 Function Block P_VAR (cal
Page 254 and 255:
Chapter 7 Function Block The princi
Page 256 and 257:
Chapter 7 Function Block *. SM400 i
Page 258 and 259:
Chapter 7 Function Block In view of
Page 260 and 261:
Chapter 7 Function Block itself. As
Page 262 and 263:
Chapter 7 Function Block • DVP se
Page 264 and 265:
Chapter 7 Function Block Function b
Page 266 and 267:
Chapter 7 Function Block HC_POINTER
Page 268 and 269:
Chapter 7 Function Block program in
Page 270 and 271:
Chapter 7 Function Block The functi
Page 272 and 273:
Chapter 7 Function Block Please ref
Page 274 and 275:
Chapter 7 Function Block After the
Page 276 and 277:
Chapter 7 Function Block Open the w
Page 278 and 279:
Chapter 7 Function Block Obviously,
Page 280 and 281:
Chapter 8 Ladder Diagram Table of C
Page 282 and 283:
Chapter 8 Ladder Diagram Local symb
Page 284 and 285:
Chapter 8 Ladder Diagram Selecting
Page 286 and 287:
Chapter 8 Ladder Diagram (4) After
Page 288 and 289:
Chapter 8 Ladder Diagram (b) ‣ Bo
Page 290 and 291:
Chapter 8 Ladder Diagram Users can
Page 292 and 293:
Chapter 8 Ladder Diagram (2) Select
Page 294 and 295:
Chapter 8 Ladder Diagram (2) Click
Page 296 and 297:
Chapter 8 Ladder Diagram The steps
Page 298 and 299:
Chapter 8 Ladder Diagram 8.2.10 Sym
Page 300 and 301:
Chapter 8 Ladder Diagram The networ
Page 302 and 303:
Chapter 9 Function Block Diagram Ta
Page 304 and 305:
Chapter 9 Function Block Diagram Lo
Page 306 and 307:
Chapter 9 Function Block Diagram T
Page 308 and 309:
Chapter 9 Function Block Diagram (e
Page 310 and 311:
Chapter 9 Function Block Diagram In
Page 312 and 313:
Chapter 9 Function Block Diagram Ex
Page 314 and 315:
Chapter 9 Function Block Diagram fo
Page 316 and 317:
Chapter 9 Function Block Diagram fu
Page 318 and 319:
Page 320 and 321:
Page 322 and 323:
Chapter 9 Function Block Diagram an
Page 324 and 325:
Chapter 9 Function Block Diagram
Page 326 and 327:
Chapter 9 Function Block Diagram If
Page 328 and 329:
Chapter 9 Function Block Diagram Ri
Page 330 and 331:
Chapter 10 Instruction List Table o
Page 332 and 333:
Chapter 10 Instruction List The ope
Page 334 and 335:
Chapter 10 Instruction List • As
Page 336 and 337:
Chapter 10 Instruction List If user
Page 338 and 339:
Chapter 10 Instruction List Users
Page 340 and 341:
Chapter 10 Instruction List 10.2.4.
Page 342 and 343:
Chapter 11 Structured Text Table of
Page 344 and 345:
Chapter 11 Structured Text A comple
Page 346 and 347:
Chapter 11 Structured Text Data for
Page 348 and 349:
Chapter 11 Structured Text However,
Page 350 and 351:
Chapter 11 Structured Text Example
Page 352 and 353:
Page 354 and 355:
Page 356 and 357:
Chapter 11 Structured Text 11.2.5 L
Page 358 and 359:
Chapter 11 Structured Text 11.2.7 A
Page 360 and 361:
Page 362 and 363:
Chapter 11 Structured Text larger t
Page 364 and 365:
Chapter 11 Structured Text 11.3.3 I
Page 366 and 367:
Chapter 11 Structured Text 11.4 Exa
Page 368 and 369:
Chapter 11 Structured Text Create t
Page 370 and 371:
Chapter 11 Structured Text which is
Page 372 and 373:
Chapter 12 Sequential Function Char
Page 374 and 375:
Page 376 and 377:
Page 378 and 379:
Page 380 and 381:
Page 382 and 383:
Page 384 and 385:
Page 386 and 387:
Page 388 and 389:
Page 390 and 391:
Page 392 and 393:
Page 394 and 395:
Page 396 and 397:
Page 398 and 399:
Page 400 and 401:
Page 402 and 403:
Page 404 and 405:
Page 406 and 407:
Page 408 and 409:
Page 410 and 411:
Page 412 and 413:
Chapter 13 Auxiliary Editing Tools
Page 414 and 415:
Page 416 and 417:
Page 418 and 419:
Page 420 and 421:
Page 422 and 423:
Page 424 and 425:
Page 426 and 427:
Page 428 and 429:
Page 430 and 431:
Page 432 and 433:
Page 434 and 435:
Page 436 and 437:
Page 438 and 439:
Page 440 and 441:
Page 442 and 443:
Page 444 and 445:
Page 446 and 447:
Page 448 and 449:
Page 450 and 451:
Page 452 and 453:
Chapter 14 Test Tools and Debugging
Page 454 and 455:
Page 456 and 457:
Page 458 and 459:
Page 460 and 461:
Page 462 and 463:
Page 464 and 465:
Page 466 and 467:
Page 468 and 469:
Page 470 and 471:
Page 472 and 473:
Page 474 and 475:
Page 476 and 477:
Page 478 and 479:
Page 480 and 481:
Page 482 and 483:
Page 484 and 485:
Page 486 and 487:
Page 488 and 489:
Chapter 15 Password Management and
Page 490 and 491:
Page 492 and 493:
Page 494 and 495:
Page 496 and 497:
Page 498 and 499:
Page 500 and 501:
Page 502 and 503:
Chapter 16 Network Configuration an
Page 504 and 505:
ISPSoft User Manual 16.1 Network Co
Page 506 and 507:
ISPSoft User Manual DHCP is a proto
Page 508 and 509:
ISPSoft User Manual NWCONFIG can al
Page 510 and 511:
ISPSoft User Manual address or RS-4
Page 512 and 513:
ISPSoft User Manual (4) Complete a
Page 514 and 515:
ISPSoft User Manual The users can a
Page 516 and 517:
ISPSoft User Manual There are two w
Page 518 and 519:
ISPSoft User Manual • Method 2 Cl
Page 520 and 521:
ISPSoft User Manual Additional rema
Page 522 and 523:
ISPSoft User Manual • Deleting a
Page 524 and 525:
ISPSoft User Manual • Deleting se
Page 526 and 527:
ISPSoft User Manual (b) After users
Page 528 and 529:
ISPSoft User Manual In the Network
Page 530 and 531:
ISPSoft User Manual • Hiding/Disp
Page 532 and 533:
ISPSoft User Manual The system chec
Page 534 and 535:
ISPSoft User Manual station address
Page 536 and 537:
ISPSoft User Manual After the users
Page 538 and 539:
ISPSoft User Manual (4) After the d
Page 540 and 541:
ISPSoft User Manual • Method 3 Ri
Page 542 and 543:
ISPSoft User Manual boxes at the le
Page 544 and 545:
ISPSoft User Manual Column Serial N
Page 546 and 547:
ISPSoft User Manual • Linked Devi
Page 548 and 549:
ISPSoft User Manual Related setting
Page 550 and 551:
ISPSoft User Manual The present net
Page 552 and 553:
ISPSoft User Manual Setting area:
Page 554 and 555:
ISPSoft User Manual The indicators
Page 556 and 557:
ISPSoft User Manual Users can type
Page 558 and 559:
ISPSoft User Manual An Ether Link i
Page 560 and 561:
ISPSoft User Manual Information ar
Page 562 and 563:
ISPSoft User Manual (5) Type a data
Page 564 and 565:
ISPSoft User Manual If a specific n
Page 566 and 567:
ISPSoft User Manual • Method 2 Do
Page 568 and 569:
ISPSoft User Manual • Multiple no
Page 570 and 571:
ISPSoft User Manual • Multiple no
Page 572 and 573:
ISPSoft User Manual 16.4.9 Enabling
Page 574 and 575:
ISPSoft User Manual Additional rema
Page 576 and 577:
ISPSoft User Manual 16.4.10 Startin
Page 578 and 579:
ISPSoft User Manual ‣ Method 2 Se
Page 580 and 581:
ISPSoft User Manual After a node is
Page 582 and 583:
ISPSoft User Manual 16.5.2.2 Descri
Page 584 and 585:
ISPSoft User Manual (1) Users have
Page 586 and 587:
Chapter 17 Data Backup and Data Res
Page 588 and 589:
Page 590 and 591:
Page 592 and 593:
Page 594 and 595:
Page 596 and 597:
Page 598 and 599:
Appendix A USB Connection Table of
Page 600 and 601:
Appendix A USB Connection Specify a
Page 602 and 603:
Appendix A USB Connection *. The de
Page 604 and 605:
Appendix A USB Connection If the de
Page 606 and 607:
Appendix B Important Points Related
Page 608 and 609:
Page 610 and 611:
Page 612 and 613:
Page 614 and 615:
Appendix C Print Management Tool Ta
Page 616 and 617:
Appendix C Print Management Tool C.
show all

ISPSoft User Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?