LEEP System 1000Â® Workstation Operating ... - CooperSurgical

More documents

Recommendations

Info

$Silicone (Latex Free) English EC REP 0086 - CooperSurgical$

Section 2 Locate all three product boxes. Unpacking and Assembly 2.1 Unpacking the LEEP Cart (box #1) When it comes to unpacking the carton that contains the Cart, great care must be taken. The box must be on its side (following the markings on the carton for which side is up) and the Cart rolled out. Orient the box as shown in Photo A. CAUTION: DO NOT PICK THE CART UP OUT OF THE SHIPPING BOX BY ITS HANDLES. THE HANDLES ARE NOT DESIGNED TO ACCOMMODATE THE FULL WEIGHT OF THE CART. 1. After removing the Cart from the shipping box, lock the front two casters. 2. Install the Smoke Evacuator next. Photo A 2 LEEP System 1000 ® Workstation • Operating Manual
LEEP System 1000 ® Electrosurgical Generator Control Panel LEEP Cart To the outlet LEEP System 1000 Electrosurgical Generator (A) (B) Pivot Hinge Door Smoke Evacuator Locking Caster (wheel) (1 of 2) Insert two screws in each hinge Figure 1 2.2 Unpacking and Installing the Smoke Evacuator (box #2) Required Tools: Phillips Screwdriver After unpacking the Smoke Evacuator box, 1. Remove the screws on the base of the Cart in preparation for attaching the Smoke Evacuator. 2. Then align the pivot hinges on the Smoke Evacuator with the screw holes on the Cart itself and fasten the Smoke Evacuator to the Cart. Make sure that the screws are tight, but DO NOT OVERTIGHTEN. 3. Remove the screws on the side of the Smoke Evacuator and then fasten down the bracket of the drop hinge to the Smoke Evacuator. See Figure 1. NOTE: The Smoke Evacuator Controls are located at the top front of the LEEP Cart for easy access. 4. Install the Electrosurgical Generator next. 2.3 Unpacking and Installing the LEEP System 1000 ® Electrosurgical Generator (box #3) After unpacking the Electrosurgical Generator box, align the pins on the bottom of the Electrosurgical Generator with the corresponding holes located on the top of the Cart. See Figure 1. Face the Electrosurgical Generator toward the front of the Cart (where the door is) and drop the cord through the rectangular cutout located at the top of the Cart. Do not hook up this cord until you have installed the filter and tubing in the Smoke Evacuator. LEEP System 1000 ® Workstation • Operating Manual 3
Page 1: LEEP System 1000 ® Workstation Mod
Page 4 and 5: Table of Contents (continued) Secti
Page 8 and 9: 2.4 Installing the Filters and Tubi
Page 10 and 11: Figures 3 through 5 show the proper
Page 12 and 13: Section 4 Front Panel of the LEEP S
Page 14 and 15: 5.2 Indications The LEEP procedure
Page 16 and 17: Section 6 Operating the System NOTE
Page 18 and 19: REMEMBER, THIS IS NOT AN ATTEMPT TO
Page 20 and 21: • The electrical cord of the Elec
Page 22 and 23: Section 11 Cleaning the LEEP System
Page 24 and 25: Section 15 Service and Repair LEEP
Page 26 and 27: Immunity Test IEC 60601 Test Level
Page 28 and 29: 17.2 General Specifications - LEEP
Page 30 and 31: 17.3 Smoke Evacuator INPUT VOLTAGE
Page 32: NOTES 28 LEEP System 1000 ® Workst

LEEP System 1000Â® Workstation Operating ... - CooperSurgical

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?