Chip Blaster manual - Salvex
Chip Blaster manual - Salvex Chip Blaster manual - Salvex
ChipBLASTER, Inc. 36 14.0. PREVENTATIVE MAINTENANCE (Cont.): 14.15. DUAL MANUAL FILTER: (CHIPBLASTER OPERATING) ! ! USE EXTREME CAUTION WHEN CHANGING THE FILTER BAG WHILE THE MACHINE IS IN OPERATION. MAKE SURE TO LOCK OUT THE BALL VALVE TO PREVENT COOLANT FROM COMING THROUGH THE FILTER THAT IS BEING SERVICED. IF THE BALL VALVE IS POSITIONED TO DIRECT FLOW WHILE THE LID IS OFF POTENTIAL PERSONAL INJURY COULD RESULT. 14.15.1. Check the handle of the filter ball valve. If the handle is in the horizontal position (running "B" filter) than it is safe to change filter "A". 14.15.2. If the filter ball valve is in the vertical position (running "A" filter) then it is safe to change filter "B". 14.15.3. Make sure the air bleed petcocks are opened before changing the filter bag. 14.15.4. Remove lid and inspect for damage. Be careful not to damage filter hold down plate, seal or springs. Set lid aside. 14.15.5. Remove optional hydrocyclonic filter (if used) from center of bag. 14.15.6. Pull the filter bag out of the housing. 14.15.7. Install the new filter bag in the housing. 14.15.8. Replace the optional hydrocyclonic filter (if used). 14.15.9. Inspect the O-ring for cracks or tears, replace if damaged. 14.15.10. Inspect filter hold down seal for cracks or tears, replace if damaged. 14.15.11. Replace the filter lid. Make sure the O-ring is in the proper groove before replacing the lid. Replace the filter lid by setting straight down so that the filter hold down plate will contact filter bag. 14.15.12. Torque filter lid cap screws to 30 FT LB (41Nm) in a star pattern. 14.15.13. Refer to SECTION 11 START UP FOR FILTER PURGE. 14.15
ChipBLASTER, Inc. 37 14.0. PREVENTATIVE MAINTENANCE (Cont.): 14.16. AUTO CROSS OVER: ("A" filter change while unit is in operation). 14.16.1. Change the filter only when the "CHANGE FILTER LIGHT" is flashing. 14.16.2. Place the "CHANGE FILTER" key switch in the change filter position. Remove the key. 14.16.3. Open the "A" filter petcock to make sure there is no pressure coming out of the filter housing. 14.16.4. If air or coolant is coming out of this valve. DO NOT PROCEED, PLEASE CALL THE FACTORY FOR ASSISTANCE. 14.16.5. Remove lid and inspect for damage. Be careful not to damage filter hold down plate, seal or springs. Set lid aside. 14.16.6. Remove optional hydrocyclonic filter (if used) from center of bag. 14.16.7. Pull the filter bag out of the housing. Close the filter air purge petcock. 14.16.8. Install the new filter bag in the housing. 14.16.9. Replace the optional hydrocyclonic filter (if used). 14.16.10. Inspect the O-ring for cracks or tears, replace if damaged. 14.16.11. Inspect filter hold down seal for cracks or tears, replace if damaged. 14.16.12. Replace the filter lid. Make sure the O-ring is in the proper groove before replacing the lid. Replace the filter lid by setting straight down so that the filter hold down plate will contact filter bag. 14.16.13. Torque filter lid cap screws to 30 FT LB (41Nm) in a star pattern. 14.16.14. Refer to SECTION 11 START UP FOR FILTER PURGE. DO NOT CHANGE THE "B" FILTER WHILE THE UNIT IS RUNNING. THE "B" FILTER IS USED ONLY AS A BACKUP FILTER TANK TO CHANGE THE "A" FILTER WHILE THE UNIT IS RUNNING. 14.16.11. Both filters can be changed while the unit is shut off. 14.16.12. Refer to SECTION 11 START UP FOR FILTER PURGE after the filter(s) have been changed.
- Page 1 and 2: . P/N: MAN-EV001TC HIGH PRESSURE/HI
- Page 3 and 4: ChipBLASTER, Inc. 3 GENERAL: This m
- Page 5 and 6: ChipBLASTER, Inc. 5 2.0. TABLE OF C
- Page 7 and 8: ChipBLASTER, Inc. 7 2.0. TABLE OF C
- Page 9 and 10: ChipBLASTER, Inc. 9 3.0. EV13, EVHP
- Page 11 and 12: ChipBLASTER, Inc. 11 4.0. SAFETY PR
- Page 13 and 14: ChipBLASTER, Inc. 13 4.1. EXPLANATI
- Page 15 and 16: ChipBLASTER, Inc. 15 4.1. EXPLANATI
- Page 17 and 18: ChipBLASTER, Inc. 17 7.0. PLACING A
- Page 19 and 20: ChipBLASTER, Inc. 19 8.0. MECHANICA
- Page 21 and 22: ChipBLASTER, Inc. 21 11.0. SYSTEM A
- Page 23 and 24: ChipBLASTER, Inc. 23 12.0. OPERATIO
- Page 25 and 26: ChipBLASTER, Inc. 25 12.0. OPERATIO
- Page 27 and 28: ChipBLASTER, Inc. 27 13.0. ALARMS:
- Page 29 and 30: ChipBLASTER, Inc. 29 14.0. PREVENTA
- Page 31 and 32: ! ChipBLASTER, Inc. 31 14.0. PREVEN
- Page 33 and 34: ChipBLASTER, Inc. 33 14.0. PREVENTA
- Page 35: ChipBLASTER, Inc. 35 14.0. PREVENTA
- Page 39 and 40: ChipBLASTER, Inc. 39 14.0. PREVENTA
- Page 41 and 42: ! ChipBLASTER, Inc. 41 14.0. PREVEN
- Page 43 and 44: ChipBLASTER, Inc. 43 Fault Systems
- Page 45 and 46: ChipBLASTER, Inc. 45 15.0. TROUBLES
- Page 47 and 48: ChipBLASTER, Inc. 47 15.0. TROUBLES
- Page 49 and 50: ChipBLASTER, Inc. 49 15.0. TROUBLES
- Page 51 and 52: ChipBLASTER, Inc. 51 15.0. TROUBLES
- Page 53 and 54: ChipBLASTER, Inc. 53 15.0. TROUBLES
- Page 55 and 56: ChipBLASTER, Inc. 55 15.0. TROUBLES
- Page 57 and 58: ChipBLASTER, Inc. 57 16.0. PRESSURE
- Page 59 and 60: ChipBLASTER, Inc. 59 17.0. HIGH PRE
- Page 61 and 62: ChipBLASTER, Inc. 61 18.0. BELT INS
- Page 63 and 64: ChipBLASTER, Inc. 63 18.0. BELT INS
- Page 65 and 66: ChipBLASTER, Inc. 65 19.0. SYSTEM C
- Page 67 and 68: ChipBLASTER, Inc. 67 20.1. Power Wi
- Page 69 and 70: ChipBLASTER, Inc. 69 20.5. PLC Inpu
- Page 71 and 72: ChipBLASTER, Inc. 71 20.9. Drive Co
- Page 73 and 74: ChipBLASTER, Inc. 73 20.15. Interfa
- Page 75 and 76: ChipBLASTER, Inc. 75 21.1. Single F
- Page 77 and 78: ChipBLASTER, Inc. 77 21.3. Autocros
- Page 79 and 80: ChipBLASTER, Inc. 79 22.6. EV Singl
- Page 81 and 82: ChipBLASTER, Inc. 81 22.16. EV Filt
- Page 83 and 84: ChipBLASTER, Inc. 83 22.22. EV Sub
- Page 85 and 86: ChipBLASTER, Inc. 85 22.28. EV Tank
<strong>Chip</strong>BLASTER, Inc. 36<br />
14.0. PREVENTATIVE MAINTENANCE (Cont.):<br />
14.15. DUAL MANUAL FILTER: (CHIPBLASTER OPERATING)<br />
!<br />
!<br />
USE EXTREME CAUTION WHEN CHANGING THE FILTER<br />
BAG WHILE THE MACHINE IS IN OPERATION.<br />
MAKE SURE TO LOCK OUT THE BALL VALVE TO PREVENT<br />
COOLANT FROM COMING THROUGH THE FILTER THAT IS BEING<br />
SERVICED. IF THE BALL VALVE IS POSITIONED TO DIRECT FLOW<br />
WHILE THE LID IS OFF POTENTIAL PERSONAL INJURY COULD<br />
RESULT.<br />
14.15.1. Check the handle of the filter ball valve. If the handle is in the horizontal<br />
position (running "B" filter) than it is safe to change filter "A".<br />
14.15.2. If the filter ball valve is in the vertical position (running "A" filter)<br />
then it is safe to change filter "B".<br />
14.15.3. Make sure the air bleed petcocks are opened before changing the filter<br />
bag.<br />
14.15.4. Remove lid and inspect for damage. Be careful not to damage filter<br />
hold down plate, seal or springs. Set lid aside.<br />
14.15.5. Remove optional hydrocyclonic filter (if used) from center of bag.<br />
14.15.6. Pull the filter bag out of the housing.<br />
14.15.7. Install the new filter bag in the housing.<br />
14.15.8. Replace the optional hydrocyclonic filter (if used).<br />
14.15.9. Inspect the O-ring for cracks or tears, replace if damaged.<br />
14.15.10. Inspect filter hold down seal for cracks or tears, replace if damaged.<br />
14.15.11. Replace the filter lid. Make sure the O-ring is in the proper groove before<br />
replacing the lid. Replace the filter lid by setting straight down so that the filter<br />
hold down plate will contact filter bag.<br />
14.15.12. Torque filter lid cap screws to 30 FT LB (41Nm) in a star pattern.<br />
14.15.13. Refer to SECTION 11 START UP FOR FILTER PURGE.<br />
14.15