Chip Blaster manual - Salvex
Chip Blaster manual - Salvex Chip Blaster manual - Salvex
ChipBLASTER, Inc. 16 5.0. STORAGE: ! 4.1 5.1. If the ChipBLASTER is to be stored for any period of time it must be keep in an area that is protected from freezing. Freezing temperatures will damage the pumps and the valves. Keep ChipBLASTER covered until ready to move to site. If MistBLASTER is also supplied keep covered. 6.0. MOVING MACHINE: ! 6.1. When moving the ChipBLASTER to the final site the following must be adhered to: 6.1.1. Lift ChipBLASTER only from the opposite end of the electrical enclosure. Forks must extend the full distance under ChipBLASTER. 6.1.2. The fork truck lifting capacity must be sufficent to safely lift the ChipBLASTER without tipping. Refer to footprint drawing (Section 23) for machine dry weight. ! MOVE SLOWLY AS NOT TO DROP THE ChipBLASTER. ! DO NOT TRY TO MOVE ChipBLASTER WITH FLUID IN TANK. ! DO NOT STAND UNDER ChipBLASTER AT ANY TIME. If MistBLASTER is supplied with ChipBLASTER: 6.2. When lifting or moving the MistBLASTER, lift only at the eye bolts provided on the top. 6.3. Sling must be of sufficent capacity to safely lift the MistBLASTER. ! ! DO NOT STAND UNDER MistBLASTER AT ANY TIME. DO NOT MOVE A ChipBLASTER WITH A MistBLASTER MOUNTED ON TOP. 5.0 - 6.0
ChipBLASTER, Inc. 17 7.0. PLACING A ChipBLASTER: 7.1. After you receive your new ChipBLASTER unit the first thing you need to do is prepare the site where you would like to place the unit. ! INSTALLATION SITE MUST BE FLAT AND LEVEL. 7.1.1. You need to keep the unit within 10’ of the machining center that you are connecting the ChipBLASTER to. 7.1.2. Locate the unit so the ChipBLASTER’s electrical cabinet is within 15’ of the machining center’s electrical cabinet. 7.1.3. Make sure you place the unit so maintenance can easily get to the filter housing and electrical cabinet on the ChipBLASTER unit. Refer to footprint drawing (Section 23) for recommended clearances. 7.2. After you have the site cleared for the ChipBLASTER unit you are ready to prepare the ChipBLASTER. 7.2.1. Remove the lumber that is used to hold the unit in place during transporation using a phillips screw driver or an electric screw gun. 7.2.2. Before you remove the ChipBLASTER from the skid take a moment and remove the lid from the top of the ChipBLASTER unit. Remove the bag containing the leveling feet. 7.2.3. When removing the ChipBLASTER only from the opposite end of the electrical enclosure. 7.2.4. Insure the forks extend completely under the ChipBLASTER unit to the support. ! DO NOT AT ANY TIME REACH UNDER THE ChipBLASTER UNIT OR STAND UNDER THE ChipBLASTER UNIT WHILE IT IS SUPPORTED BY A FORK TRUCK. IF YOU MUST REACH UNDER THE MACHINE BLOCK IT UP FOR SAFETY. 7.2.5. The EV units are shipped from the factory with leveling feet as shown in figure 1a. The leveling feet must be installed when setting up the ChipBLASTER. 7.2.8. After you remove the ChipBLASTER from the skid take the set of four feet and install the studs of the leveling feet through the holes in the legs. Block unit while installing feet for safety. Reference; top of foot to the bottom of second nut (1”). The feet have two functions the first being to level the ChipBLASTER unit and the second being to help eliminate the transfer of noise. Refer to figure 1. 7.2.9. After you have the feet in place proceed with moving the ChipBLASTER into place.
- Page 1 and 2: . P/N: MAN-EV001TC HIGH PRESSURE/HI
- Page 3 and 4: ChipBLASTER, Inc. 3 GENERAL: This m
- Page 5 and 6: ChipBLASTER, Inc. 5 2.0. TABLE OF C
- Page 7 and 8: ChipBLASTER, Inc. 7 2.0. TABLE OF C
- Page 9 and 10: ChipBLASTER, Inc. 9 3.0. EV13, EVHP
- Page 11 and 12: ChipBLASTER, Inc. 11 4.0. SAFETY PR
- Page 13 and 14: ChipBLASTER, Inc. 13 4.1. EXPLANATI
- Page 15: ChipBLASTER, Inc. 15 4.1. EXPLANATI
- Page 19 and 20: ChipBLASTER, Inc. 19 8.0. MECHANICA
- Page 21 and 22: ChipBLASTER, Inc. 21 11.0. SYSTEM A
- Page 23 and 24: ChipBLASTER, Inc. 23 12.0. OPERATIO
- Page 25 and 26: ChipBLASTER, Inc. 25 12.0. OPERATIO
- Page 27 and 28: ChipBLASTER, Inc. 27 13.0. ALARMS:
- Page 29 and 30: ChipBLASTER, Inc. 29 14.0. PREVENTA
- Page 31 and 32: ! ChipBLASTER, Inc. 31 14.0. PREVEN
- Page 33 and 34: ChipBLASTER, Inc. 33 14.0. PREVENTA
- Page 35 and 36: ChipBLASTER, Inc. 35 14.0. PREVENTA
- Page 37 and 38: ChipBLASTER, Inc. 37 14.0. PREVENTA
- Page 39 and 40: ChipBLASTER, Inc. 39 14.0. PREVENTA
- Page 41 and 42: ! ChipBLASTER, Inc. 41 14.0. PREVEN
- Page 43 and 44: ChipBLASTER, Inc. 43 Fault Systems
- Page 45 and 46: ChipBLASTER, Inc. 45 15.0. TROUBLES
- Page 47 and 48: ChipBLASTER, Inc. 47 15.0. TROUBLES
- Page 49 and 50: ChipBLASTER, Inc. 49 15.0. TROUBLES
- Page 51 and 52: ChipBLASTER, Inc. 51 15.0. TROUBLES
- Page 53 and 54: ChipBLASTER, Inc. 53 15.0. TROUBLES
- Page 55 and 56: ChipBLASTER, Inc. 55 15.0. TROUBLES
- Page 57 and 58: ChipBLASTER, Inc. 57 16.0. PRESSURE
- Page 59 and 60: ChipBLASTER, Inc. 59 17.0. HIGH PRE
- Page 61 and 62: ChipBLASTER, Inc. 61 18.0. BELT INS
- Page 63 and 64: ChipBLASTER, Inc. 63 18.0. BELT INS
- Page 65 and 66: ChipBLASTER, Inc. 65 19.0. SYSTEM C
<strong>Chip</strong>BLASTER, Inc. 16<br />
5.0. STORAGE:<br />
!<br />
4.1<br />
5.1. If the <strong>Chip</strong>BLASTER is to be stored for any period of time it must be keep in an area that is<br />
protected from freezing. Freezing temperatures will damage the pumps and the valves. Keep<br />
<strong>Chip</strong>BLASTER covered until ready to move to site. If MistBLASTER is also supplied keep<br />
covered.<br />
6.0. MOVING MACHINE:<br />
!<br />
6.1. When moving the <strong>Chip</strong>BLASTER to the final site the following must be adhered to:<br />
6.1.1. Lift <strong>Chip</strong>BLASTER only from the opposite end of the electrical enclosure.<br />
Forks must extend the full distance under <strong>Chip</strong>BLASTER.<br />
6.1.2. The fork truck lifting capacity must be sufficent to safely lift the <strong>Chip</strong>BLASTER<br />
without tipping. Refer to footprint drawing (Section 23) for machine dry weight.<br />
!<br />
MOVE SLOWLY AS NOT TO DROP THE <strong>Chip</strong>BLASTER.<br />
!<br />
DO NOT TRY TO MOVE <strong>Chip</strong>BLASTER WITH FLUID IN TANK.<br />
!<br />
DO NOT STAND UNDER <strong>Chip</strong>BLASTER AT ANY TIME.<br />
If MistBLASTER is supplied with <strong>Chip</strong>BLASTER:<br />
6.2. When lifting or moving the MistBLASTER, lift only at the eye bolts provided on the top.<br />
6.3. Sling must be of sufficent capacity to safely lift the MistBLASTER.<br />
!<br />
!<br />
DO NOT STAND UNDER MistBLASTER AT ANY TIME.<br />
DO NOT MOVE A <strong>Chip</strong>BLASTER WITH A MistBLASTER MOUNTED ON<br />
TOP.<br />
5.0 - 6.0