API-RP-576

More documents

Recommendations

Info

4.6.3 Limitations Conventional safety-relief valves should not be used in the following applications: a) where the total built-up backpressure exceeds the allowable overpressure; b) where the cold differential test pressure (CDTP) cannot be reduced to account for the effects of variable backpressure (see <strong>API</strong> 520, Part 1); c) on ASME BPVC Section I steam boiler drums or ASME BPVC Section I superheaters; d) as pressure control or bypass valves. Fion Zhnag/ Charlie Chong
http://www.leser.com/en/products/download/brochures-catalogs.html Fion Zhnag/ Charlie Chong
Page 1 and 2:
API-RP-576 Inspection of Pressure-r
Page 3 and 4:
Fion Zhang/ Charlie Chong Speaker:
Page 5 and 6:
5 Causes of Improper Performance 5.
Page 7 and 8:
1 Scope Fion Zhang/ Charlie Chong
Page 9 and 10:
The recommendations in this publica
Page 11 and 12:
This publication does not cover tra
Page 13 and 14:
pressure-relief valves Fion Zhang/
Page 15 and 16:
pilot-operated pressure-relief valv
Page 17 and 18:
upture disks Fion Zhang/ Charlie Ch
Page 19 and 20:
2 Normative References Fion Zhang/
Page 21 and 22:
• ASME PTC 25, Pressure Relief De
Page 23 and 24:
3.1 General For the purposes of thi
Page 25 and 26: galling Fion Zhang/ Charlie Chong
Page 27 and 28: 3.2 Dimensional Characteristics of
Page 29 and 30: inlet size outlet size Fion Zhang/
Page 31 and 32: Fion Zhang/ Charlie Chong huddling
Page 33 and 34: Fion Zhang/ Charlie Chong lift
Page 35 and 36: Basic Function of a Spring Loaded S
Page 37 and 38: Valve Closed. In a direct spring lo
Page 39 and 40: The pressure below the valve must i
Page 41 and 42: Fion Zhang/ Charlie Chong F p = p*A
Page 43 and 44: Functional Diagram. The following d
Page 45 and 46: 3.3 Operational Characteristics—S
Page 47 and 48: 3.3.3 maximum allowable working pre
Page 49 and 50: 3.3.4 maximum operating pressure Th
Page 51 and 52: Fion Zhang/ Charlie Chong Keywords:
Page 53 and 54: 3.4.5 burst-pressure tolerance The
Page 55 and 56: 3.4.10 marked burst pressure or rat
Page 57 and 58: 4 Pressure-relieving Devices Fion Z
Page 59 and 60: 4.2 Pressure-relief Valve Fion Zhna
Page 61 and 62: 4.3 Safety Valve. Fion Zhnag/ Charl
Page 63 and 64: 4.3.1 General. A safety valve is a
Page 65 and 66: 4.3.2 Applications A safety valve i
Page 67 and 68: Fion Zhnag/ Charlie Chong
Page 69 and 70: 4.4.1 General. A relief valve is a
Page 71 and 72: 4.5 Safety-relief Valve. Fion Zhnag
Page 73 and 74: 4.6 Conventional Safety-relief Valv
Page 75: 4.6 Conventional Safety-relief Valv
Page 81 and 82: Conventional safety valves Fig. 9.2
Page 83 and 84: Types Mediums Limitations Safety-re
Page 85 and 86: 4.7.3 Limitations Balanced safety-r
Page 87 and 88: Fion Zhnag/ Charlie Chong Fig. 9.2.
Page 89 and 90: Fion Zhnag/ Charlie Chong http://ww
Page 93 and 94: 4.8 Pilot-operated Pressure-relief
Page 95 and 96: What is a Pilot operated safety val
Page 97 and 98: 4.8 Pilot-operated Pressure-relief
Page 99 and 100: Figure 9—High-pressure Pilot-oper
Page 103 and 104: 4.8.2 Applications Pilot-operated s
Page 105 and 106: 4.9 Pressure- and/or Vacuum-vent Va
Page 107 and 108: 4.9.1 General. • A pressure- and/
Page 109 and 110: Figure 7—Low-pressure Diaphragm-t
Page 111 and 112: Figure 10—Weight-loaded Pallet Ve
Page 113 and 114: Figure 11—Spring and Weight-loade
Page 117 and 118: 5 Causes of Improper Performance Fi
Page 119 and 120: Fion Zhang/ Charlie Chong Figure 22
Page 121 and 122: Figure 25—Monel Rupture Disks Cor
Page 123 and 124: Fion Zhang/ Charlie Chong
Page 125 and 126: Fion Zhang/ Charlie Chong
Page 127 and 128:
Fion Zhang/ Charlie Chong Figure 35
Page 129 and 130:
5.1 Corrosion Fion Zhang/ Charlie C
Page 131 and 132:
Corrosion is a basic cause of many
Page 133 and 134:
http://www.valveworld.net/safetyequ
Page 135 and 136:
Because there is metal-to-metal con
Page 137 and 138:
Basic interferometry The interferen
Page 139 and 140:
As light travels through the Optica
Page 141 and 142:
Example: 1 a series of fringes indi
Page 143 and 144:
Fion Zhang/ Charlie Chong
Page 145 and 146:
Page 147 and 148:
Causes of damaged valve seats; 1. C
Page 149 and 150:
Spring failures. 2 modes of failure
Page 151 and 152:
Page 153 and 154:
Fion Zhang/ Charlie Chong The size
Page 155 and 156:
Incorrect calibration of pressure g
Page 157 and 158:
How to adjust a PSV The spring dete
Page 159 and 160:
http://www.cicpro.com/products/safe
Page 161 and 162:
The design of the shroud must be su
Page 163 and 164:
Adjustment pin affect the character
Page 165 and 166:
Page 167 and 168:
5.5 Plugging and Sticking Fion Zhan
Page 169 and 170:
5.6 Misapplication of Materials Fio
Page 171 and 172:
Typical ball valve material selecti
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
5.7 Improper Location, History, or
Page 179 and 180:
Fion Zhang/ Charlie Chong V-203
Page 181 and 182:
Page 183 and 184:
Rough handling can occur during;
Page 185 and 186:
The following table summarises the
Page 187 and 188:
Greater differentials between opera
Page 189 and 190:
5.10 Improper Discharge Piping Test
Page 191 and 192:
Fion Zhang/ Charlie Chong When hydr
Page 193 and 194:
Fion Zhang/ Charlie Chong the bello
Page 195 and 196:
5.11 Improper Handling, Installatio
Page 197 and 198:
Rupture disk problems are often ass
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
6.1 Reasons for Inspection and Test
Page 211 and 212:
6.2.2 Safety 1. proper authority an
Page 213 and 214:
National Board approved ASME stamps
Page 215 and 216:
The Kdr or aW value can vary accord
Page 217 and 218:
6.2.5 Removal of Device from System
Page 219 and 220:
Exercise; Dismantling of PSV Fion Z
Page 221 and 222:
Highly Reactive Materials Water-Rea
Page 223 and 224:
6.2.7 Inspection of Adjacent Inlet
Page 225 and 226:
Fion Zhang/ Charlie Chong Rupture d
Page 227 and 228:
6.2.10 Visual Inspection This inspe
Page 229 and 230:
6.2.11 Dismantling of Valve. Disman
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Portable Test Separator Internal &
Page 239 and 240:
The pilot assembly and dome area co
Page 241 and 242:
6.2.13 Reconditioning and Replaceme
Page 243 and 244:
Fion Zhang/ Charlie Chong Most test
Page 245 and 246:
Page 247 and 248:
After the valve has been adjusted,
Page 249 and 250:
Check for leakage during pressuriza
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
6.2.17 Completion of Necessary Reco
Page 259 and 260:
when a valve operates in nonfouling
Page 261 and 262:
ASME BPVC Section I requires; • B
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
6.2.20 Inspection, Testing, Mainten
Page 269 and 270:
6.2.21 Inspection, Testing, Mainten
Page 271 and 272:
6.3 Visual On-stream Inspection Vis
Page 273 and 274:
6.4.2 Frequency of Shop Inspection/
Page 275 and 276:
Manufacturer’s Basis • Manufact
Page 277 and 278:
API572, 6.4.3 Frequency of Visual O
Page 279 and 280:
Routine • inspection least interf
Page 281 and 282:
7.1 Objective The primary objective
Page 283 and 284:
7.3 Responsibilities Some companies
Page 285 and 286:
Annex A (informative) Pressure-reli
Page 287 and 288:
API576 Charlie Chong/ Fion Zhang/ H
Page 289 and 290:
Page 291 and 292:
A.1 Need and Function of Test Block
Page 293 and 294:
A.2 Testing with Air • Air is com
Page 295 and 296:
A.4 Description of Test Block The s
Page 297 and 298:
Key 1. test station 2. adaptor for
Page 299 and 300:
show all

API-RP-576

Create successful ePaper yourself

Delete template?

Save as template?