Welding Inspection & Metallurgy API ICP Self Study Notes

More documents

Recommendations

Info

Inspector: An individual who is qualified and certified to perform inspections under the proper inspection code or who holds a valid and current National Board Commission. He/She must be: • Qualified and Certified under proper inspection code (AWS/ <strong>API</strong>/ CSWIP/ Local or National Accreditation?) • NBC-National Board Commission certified.
Qualified & Certified Inspectors http://acri.mystrategiccompass.com/training/certifications/551 http://www.nationalboard.org/ Expert at works
Page 1:
Welding Inspection & Metallurgy API
Page 6 and 7:
http://myicp.api.org/DirectorySearc
Page 8:
This recommended practice provides
Page 11 and 12:
http://www.smt.sandvik.com/en/searc
Page 13 and 14:
Content: 1 SCOPE 2 REFERENCES 2.1 C
Page 15 and 16:
6 WELDING PROCEDURE 6.1 General 6.2
Page 17 and 18:
10 METALLURGY 10.1 General 10.2 The
Page 19 and 20:
1 Scope
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
API 577 is to aid the inspector in
Page 31 and 32:
API Std 653 Tank Inspection, Repair
Page 33 and 34:
How this API Standard relates with
Page 35 and 36:
API 510: 8.1 SCOPE AND SPECIFIC EXE
Page 50 and 51: The level of learning and training
Page 52: Study Harder
Page 55 and 56: Problems encountered during welding
Page 57: Welds selected for inspection, and
Page 61 and 62: A welding engineer should be consul
Page 65 and 66: 2 References
Page 67 and 68: API • API 510 Pressure Vessel Ins
Page 69 and 70: AWS • A2.4 Standard Symbols for W
Page 71 and 72: API • RP 572 Inspection of Pressu
Page 73: 3 Definitions
Page 77 and 78: Fillet Weld Actual throat Theoretic
Page 79 and 80: Arc strike
Page 81 and 82: Arc blow
Page 83 and 84: 3.12 burn-through: A non-standard t
Page 85 and 86: 3.16 defect: A discontinuity or dis
Page 87 and 88: 3.22 fillet weld size: For equal le
Page 89 and 90: Electrodes
Page 91 and 92: HAZoning
Page 93 and 94: 3.26 heat input: the energy supplie
Page 95 and 96: Hot cracking
Page 97 and 98: Hot cracking http://en.wikipedia.or
Page 99: 3.31 inspector: An individual who i
Page 103 and 104: Qualified & Certified Inspectors
Page 106 and 107: Figure A-1—Joint Types and Applic
Page 108 and 109: Figure A-1—Joint Types and Applic
Page 110 and 111: lamellar tear
Page 114 and 115: Longitudinal crack
Page 116 and 117: PMI
Page 122 and 123: 3.45 peening: The mechanical workin
Page 124 and 125: Porosity
Page 126 and 127: Slag Inclusions
Page 128 and 129: Slag inclusions http://www.ge-mcs.c
Page 130 and 131: Porosity
Page 132 and 133: 3.61 tungsten inclusion: A disconti
Page 134 and 135: Transverse crack
Page 136 and 137: Transverse Crack
Page 138 and 139: TIG Welding - Tungsten Inclusions
Page 140 and 141: TIG Welding - Tungsten Inclusions
Page 142 and 143: weldment: An assembly whose compone
Page 144 and 145: weld reinforcement weld toe
Page 146 and 147: weld reinforcement weld toe
Page 148 and 149: 4 Welding Inspection
Page 150 and 151:
4.2 TASKS PRIOR TO WELDING The impo
Page 152:
4.2.1 Drawings, Codes, and Standard
Page 157 and 158:
i. Preheat requirements and accepta
Page 159 and 160:
Review requirements for the weldmen
Page 161 and 162:
4.2.2.1 Quality control items to as
Page 163 and 164:
Page 166:
4.2.4 NDE Information Confirm the N
Page 170 and 171:
Welding Equipment and Instruments
Page 172 and 173:
4.2.6 Heat Treatment and Pressure T
Page 174 and 175:
4.2.7 Materials Ensure all filler m
Page 176 and 177:
Materials
Page 178 and 179:
Page 180 and 181:
Weld Preparation- Fit-up & Dimensio
Page 182 and 183:
4.2.10 Welding Consumables Confirm
Page 185 and 186:
4.3.1 Quality Assurance Establish a
Page 187 and 188:
. Mock-up weldment, if required, me
Page 189 and 190:
In-process ferrite measurement
Page 191 and 192:
In-process ferrite measurement Why
Page 193 and 194:
Schaeffer diagram
Page 195 and 196:
4.4.1 Appearance and Finish Verify
Page 197 and 198:
Field hardness check
Page 199 and 200:
4.4.2 NDE Review Verify NDE is perf
Page 201 and 202:
4.4.3 Post-weld Heat Treatment Veri
Page 203 and 204:
PWHT Procedure
Page 205 and 206:
Metal temperature of component meet
Page 207 and 208:
4.5 NON-CONFORMANCES AND DEFECTS At
Page 209 and 210:
4.7 SAFETY PRECAUTIONS Inspectors s
Page 211 and 212:
Sevan Driller I
show all

Welding Inspection & Metallurgy API ICP Self Study Notes

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?