Mounting the Basic 540 protective cell - Step four
Mounting the Basic 540 protective cell - Step four Mounting the Basic 540 protective cell - Step four
Mounting the Basic 540 protective cell right side panel front panel rear panel left side panel IMPORTANT: Do not exchange front and rear panel! connecting tube (36x870mm) thread rod (m6x1m) Seite 1 Datum: 02.08.2005 Pfad:G:\Neue Datenstruktur\Produkte\Fräsen\Basic 540\Schutzzelle\Protective cell Basic 540.doc
- Page 2 and 3: Polycarbone plate: L-profiles polyc
- Page 4: Seite 4 Datum: 02.08.2005 Pfad:G:\N
<strong>Mounting</strong> <strong>the</strong> <strong>Basic</strong> <strong>540</strong> <strong>protective</strong> <strong>cell</strong><br />
right side panel front panel rear panel left side panel<br />
IMPORTANT: Do not exchange front and rear panel!<br />
connecting tube<br />
(36x870mm)<br />
thread rod<br />
(m6x1m)<br />
Seite 1 Datum: 02.08.2005 Pfad:G:\Neue Datenstruktur\Produkte\Fräsen\<strong>Basic</strong> <strong>540</strong>\Schutzzelle\Protective<br />
<strong>cell</strong> <strong>Basic</strong> <strong>540</strong>.doc
Polycarbone plate:<br />
L-profiles<br />
polycarbonate plate<br />
IMPORTANT: Follow <strong>the</strong> instructions very carefully when glueing<br />
<strong>the</strong> L-profiles to <strong>the</strong> polycarbontae plate (see drawing).<br />
20mm<br />
20 mm<br />
20mm<br />
862x680mm<br />
20mm<br />
862x520mm<br />
1. Clean <strong>the</strong> <strong>four</strong> L-profiles.<br />
2. Glue <strong>the</strong> 3M tape on <strong>the</strong> inner dies of <strong>the</strong> L-profiles.<br />
3. Put <strong>the</strong> L-profiles carefully on <strong>the</strong> polycarbonate plate.<br />
Seite 2 Datum: 02.08.2005 Pfad:G:\Neue Datenstruktur\Produkte\Fräsen\<strong>Basic</strong> <strong>540</strong>\Schutzzelle\Protective<br />
<strong>cell</strong> <strong>Basic</strong> <strong>540</strong>.doc
<strong>Mounting</strong> instructions:<br />
1. Put <strong>the</strong> <strong>four</strong> plates toge<strong>the</strong>r.<br />
2. Do not tighten <strong>the</strong> screws completely.<br />
3. Put <strong>the</strong> thread rod through <strong>the</strong> hole in <strong>the</strong> side panels and <strong>the</strong><br />
connecting tube.<br />
4. Put <strong>the</strong> two polycarbonate plates into <strong>the</strong> designated grooves.<br />
5. Tighten <strong>the</strong> screws now.<br />
6. Cut <strong>the</strong> thread rod so that 3mm will overlap and fix <strong>the</strong> screws.<br />
Seite 3 Datum: 02.08.2005 Pfad:G:\Neue Datenstruktur\Produkte\Fräsen\<strong>Basic</strong> <strong>540</strong>\Schutzzelle\Protective<br />
<strong>cell</strong> <strong>Basic</strong> <strong>540</strong>.doc
Seite 4 Datum: 02.08.2005 Pfad:G:\Neue Datenstruktur\Produkte\Fräsen\<strong>Basic</strong> <strong>540</strong>\Schutzzelle\Protective<br />
<strong>cell</strong> <strong>Basic</strong> <strong>540</strong>.doc