In System Programming (ISP) for ATMEL chips
In System Programming (ISP) for ATMEL chips
In System Programming (ISP) for ATMEL chips
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>In</strong> <strong>System</strong> Programmer (<strong>ISP</strong>) <strong>for</strong> <strong>ATMEL</strong> micro controllers<br />
http://www.ikalogic.com/isp.php<br />
Page 28 of 29<br />
26-02-2008<br />
Sarma<br />
Reply With Quote<br />
Posted by:<br />
Daniel8484<br />
on: 23 Jan 2008<br />
I got it working with 1 meter cable :D, just add the 10k resitor and 10u Capacitor on the rst as<br />
suggested.<br />
Thanks <strong>for</strong> share with us your <strong>ISP</strong> =D<br />
I have just one question... i need a cable that works with BASCOM 8051 from atmel directly, i<br />
saw that BASCOM supports STK200/300, there is a way to ajust your model to turn it similar<br />
to stk and bascom see it?<br />
Or you have any in<strong>for</strong>mation of anyone that got BASCOM to program a 89s52? and what cable<br />
he uses?<br />
Thanks <strong>for</strong> any help :D<br />
Reply With Quote<br />
Posted by:<br />
MVS Sarma<br />
on: 31 Jan 2008<br />
[Quoting: yo] i get "no data in file" error when trying to program this file have been tested<br />
in other programmer and worked can u help me out<br />
CAN YOU PUT YOUR FILE COPY SO THAT WE COULD ANALYZE BY SIMULATION<br />
Sarma<br />
Reply With Quote<br />
Posted by:<br />
pratham<br />
on: 04 Feb 2008<br />
Hi,<br />
I am trying to program the AT89S52.<br />
The software does not give an error while reading the flash.<br />
(It reads the flash as all 0xFF which looks ok),<br />
but if I try to program the flash, it gives an error message:<br />
"Write error at adress 00000000 byte written 01 byte read FF"<br />
Can you suggest the possible reason <strong>for</strong> this?<br />
Can I presume that the read operation is working ok?<br />
Thanks & Regards,<br />
Pratham.<br />
Reply With Quote<br />
Posted by:<br />
MVS Sarma<br />
on: 06 Feb 2008<br />
It is clear that it is not writing, so 0xff remain there.<br />
please check the connections at pin31 to Vdd is proper. also check whether you have the 10uF<br />
and parallel104 disc cap as filter between pins 40(Vdd) and PIN20 (Vss).check the setting of<br />
programming speed in the ispprog software<br />
set it to "1/16" th or less of the crystal you have used.<br />
you also ensure that the cable used is not longer than say 15or 20 inches. better slect the<br />
device manually instead of leaving to software.<br />
Reply With Quote<br />
POSTING REPLIES IS TEMPORARLY BANNED DUE TO SPAM ACTIVITY<br />
Any comments are welcome at ika@ikalogic.com<br />
Unless mentioned, all content is written and designed by Ibrahim Kamal, copying is prohibited and unethical<br />
Home | Articles & Resources | Forums | contact | Check mail | About ika<br />
Ads by Google ADSL <strong>ISP</strong> <strong>ISP</strong> Dialups Pic Programmer BT <strong>ISP</strong><br />
All content on this site is provided as is and without any guarantee of any kind. We cannot be held responsible <strong>for</strong> any errors,<br />
omissions, or damages arising out of use of in<strong>for</strong>mation available on this web site.<br />
IMPORTANT COPYRIGHT NOTE: Electronics and Robotics Articles by Ibrahim<br />
KAMAL are licensed under a Creative Commons Attribution-Noncommercial-No<br />
Derivative Works 3.0 United States License.
Change language