In System Programming (ISP) for ATMEL chips
In System Programming (ISP) for ATMEL chips
In System Programming (ISP) for ATMEL chips
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>In</strong> <strong>System</strong> Programmer (<strong>ISP</strong>) <strong>for</strong> <strong>ATMEL</strong> micro controllers<br />
http://www.ikalogic.com/isp.php<br />
Page 24 of 29<br />
26-02-2008<br />
All the best<br />
Sarma<br />
Reply With Quote<br />
Posted by:<br />
Ronald<br />
on: 03 Dec 2007<br />
Posted by:<br />
Ibrahim Kamal<br />
on: 04 Dec 2007<br />
Can I connect a parallel db db25 which is used to connect between the PC to print, to connect<br />
to at89s52 <strong>for</strong> isp?<br />
Reply With Quote<br />
[Quoting: Ronald] Can I connect a parallel db db25 which is used to connect between the PC<br />
to print, to connect to at89s52 <strong>for</strong> isp?<br />
Yes, but you may have to shorten the cable to 1m or less<br />
Reply With Quote<br />
Posted by:<br />
lellis<br />
on: 04 Dec 2007<br />
hi. can I program the atmega48V whith the isp programmer? sorry , my english is not good.<br />
tks!<br />
Reply With Quote<br />
Posted by:<br />
lellis<br />
on: 04 Dec 2007<br />
I see!! may be works!! I´ll test!! and tell you!<br />
tks again!!<br />
Reply With Quote<br />
Posted by:<br />
neeru<br />
on: 06 Dec 2007<br />
Posted by:<br />
firdaus<br />
on: 09 Dec 2007<br />
Posted by:<br />
Ibrahim Kamal<br />
on: 10 Dec 2007<br />
Posted by:<br />
jigesh mehta<br />
on: 11 Dec 2007<br />
plz tell wat does basically the S series stands <strong>for</strong> in IC 89S51& how it is different 4m other<br />
series like C series etc.???<br />
Reply With Quote<br />
hallo, i m from indonesia<br />
my isp working very good but i need isp with serial port because my laptop don't have parallel<br />
port, may be can u design to me.<br />
Reply With Quote<br />
I am willing to design a serial port based <strong>ISP</strong> programmer, but be aware, it will be more<br />
complicated, and it wont be available on the site be<strong>for</strong>e a couple of monthes. What you can do<br />
right now is to use a USB to parallel port adapter. it should work without problems. good luck.<br />
Reply With Quote<br />
I am design <strong>ISP</strong> programming cable <strong>for</strong> at89s52 microcontroller. but <strong>In</strong> that i have not<br />
programe the IC AT89S52. I am seting AEC-<strong>ISP</strong>.I have problem is give Device signature is<br />
differant when many times cilk on read signature. so give help...<br />
Reply With Quote<br />
Posted by:<br />
aman<br />
on: 13 Dec 2007<br />
dear sir<br />
if i connected lcd with port 1, the entire port will be occupied with the data port of lcd..<br />
my quest is this..shall i remove the lcd data cable from the P1 be<strong>for</strong>e downloading the hex<br />
code with the isp cable because it is<br />
P1 port of the IC...or it will download the hex. i dont want to touch the hardware.<br />
it is possible to programme the chip without removing any hardware interfacing devices from<br />
the P1.<br />
aman<br />
india<br />
Reply With Quote<br />
Posted by:<br />
Bozo<br />
on: 13 Dec 2007<br />
I just won´t to say thank you wery much. I´m more then the satisfied with this programer. It<br />
isn´worked from the first time, so I modified it. At the end of the cable from the programer to<br />
the target board, I put the resistor 330E in serial with te sck line and then capacitor 120pF<br />
from the sck to gnd. Since then I have no problem. I have programed At89s2051 and<br />
Atmega8.<br />
Hello from Slovenia,<br />
Bozo