audio file in the INSERT mode - Fostex

ABS
H M S F
PGM
Recording timecode generated by the internal timecode generator
You can record timecode generated by the internal timecode generator together with audio
simultaneously.
This section describes settings and operations for timecode recording. See "Chapter 4: Audio recording/playback"
for details about settings and operations for audio recording.
The following description assumes that one of the [AUDIO RDY] key indicators ([NEW FILE] or
[INSERT]) is lit.
Settings of the DV40
• Front panel switch settings
4
4
DVD MASTER RECORDER
OPEN/CLOSE
DISP
TIME
SETUP
FILE SEL
VARI PITCH
JOG
SHUTTLE
SKIP/CURSOR
1
2
BIT
FS
kHz
24
48
DISP
LEVEL
UTILITY DIRECTORY
SHIFT
DRIVE
TAPE MODE
CHASE
LIST PLAY
-
+
∞ 60 50 42 34 28 2018 12 8 6 5 4 3 2 1 0 OL -0.1%
FORMAT
BWF
CLOCK
-INT-
MARGIN
RESET
EXIT/NO ENTER/YES
POWER
DVD
HD
space
ABC
DEF
RECORD
STOP
PLAY
TC SETUP
REWIND
EDIT
F FWD
1 2 3
GHI JKL MNO
INPUT MON
MUTE
SLATE TONE
IN
SOURCE
OUT
IN
DST
OUT
CUE POINT
MEMORY
SOURCE PLAY
LOCATE ABS 0
LOCATE REC END
4 5 6
PQRS TUV WXYZ symbol
7 8 9 0
MUTE REC TONE REC PREVIEW
AUDIO RDY
TR1 TR2 TR3 TR4
NEW FILE INSERT TC RDY AUDIO EDIT UNDO
LOCATE
STORE
HOLD
KEYBOARD
MOUSE
MIN
TR1,3+2,4
TR3+4
TR1+2
MAX
PHONES
TR4
TR3
TR2
TR1
MONO
176.4
192 30
30DF
24H RUN
96
24BIT
29.97
REC RUN
REMOTE
BWF ANALOG MONO +0.1%
88.2
29.97DF
FREE RUN
STEREO NORM
(kHz)
LOCAL
SDII DIGITAL
48
25
EXT RUN
MULTI(4TR) -0.1%
44.1
16BIT
24
PULL 48
44.1 RSVD
23.97
CONTROL AUDIO FILE INPUT TR MODE UP/DOWN SAMPLING FREQ FRAME RATE
TC GEN MODE
INT
WORD
VIDEO
DIGITAL
MIN
CLOCK
TR1
ON
OFF
BY-
PASS
MAX MIN
TR2 INPUT LEVEL
ON
OFF
BY-
PASS
MAX
TR3 TR4
3 1 2
1. Set the [FRAME RATE] switch appropriately according to timecode to be recorded.
2. Set the [TC GEN MODE] switch appropriately according to the situation.
24H RUN
REC RUN
FREE RUN
EXT RUN
Timecode starts from the current time of the internal clock of the unit.
When recording timecode to a new file, the generator records timecode from the value which
continues to the last timecode value of the previous audio file. You can also use this mode for
restriping discontinuous timecode.
Runs the internal generator by the free run mode, and records the current internal generator
time as the start time.
The external timecode value is recorded as the start time.
Unlike timecode striped on an audio or video tape, timecode on a disk is not striped from the
beginning to the end. Only the offset between the ABS time and timecode at the recording start
point is recorded.
Therefore, if you record a discontinuous timecode value in the middle, the unit cannot recognize
it. Also, the user bit when timecode starts recording is valid throughout the timecode, so
the unit cannot handle the user bit that changes in the middle.
3. Press the [TC RDY] key to arm the timecode track.
The TC RDY indicator is lit while "TC RDY" is shown on the display.
4. After pressing the [SHIFT] key to make the SHIFT mode active, press the [CHASE/SETUP] key to enter
the TC SETUP mode, then preset the internal timecode generator time if necessary.
See page 5-6 for details about how to preset the internal timecode generator time.
5-3