Stepper motors in protection class IP54/65 - Nanotec - Index of
Stepper motors in protection class IP54/65 - Nanotec - Index of
Stepper motors in protection class IP54/65 - Nanotec - Index of
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>Stepper</strong> <strong>motors</strong> <strong>in</strong> <strong>protection</strong> <strong>class</strong><br />
g AD4118L stepper motor with term<strong>in</strong>al box <strong>in</strong> <strong>protection</strong> <strong>class</strong> <strong>IP54</strong><br />
Through their electrical and mechanical <strong>in</strong>terchangeability with the standard <strong>motors</strong>, the mach<strong>in</strong>e-compliant<br />
stepper <strong>motors</strong> up to a <strong>protection</strong> <strong>class</strong> <strong>of</strong> IP 54 (except for shaft output) <strong>of</strong>fer a<br />
consistent drive concept. The extremely compact term<strong>in</strong>al box is only 16 mm longer and provides<br />
the constructor with an easy, fast and economic expansion option with high availability at the<br />
same time.<br />
In addition to use under extreme ambient conditions as well as reduced filter<strong>in</strong>g and EMC effort,<br />
prefabricated cables enable fast and faultless wir<strong>in</strong>g and commission<strong>in</strong>g.<br />
Other sizes, M12 connectors, or cable screw connections are possible on request.<br />
Encoders used: 3-channel with 500 pulses/rev and l<strong>in</strong>e driver, 5V TTL signal each (for 24V, please<br />
contact us!)<br />
Brak<strong>in</strong>g mechanism used: Brak<strong>in</strong>g power 0.4Nm, 24V, 11W<br />
Outl<strong>in</strong>e draw<strong>in</strong>g (<strong>in</strong> mm)<br />
Type<br />
Current<br />
A/phase<br />
Hold<strong>in</strong>g<br />
torque<br />
N cm<br />
Available performance categories (others on request)<br />
Resistor<br />
Ohm/phase<br />
+ -10%<br />
Inductance<br />
mH<br />
+ -20%<br />
Option<br />
Rotor <strong>in</strong>ertia<br />
torque<br />
g cm 2<br />
I I I I I I I I<br />
Weight<br />
kg<br />
Connector configuration<br />
MOTOR D-SUB-9<br />
P<strong>in</strong> assignment<br />
1 A<br />
2 A\<br />
3 B<br />
4 B\<br />
5 NC<br />
6 NC<br />
7 NC (brake)<br />
8 NC (brake/GND)<br />
9 NC<br />
Hous<strong>in</strong>g GND/shield<strong>in</strong>g<br />
Order number<br />
AD4118L 1804 -<br />
AD4118L1804 1.8 50.0 1.75 3.3 82 0.36 66<br />
Without option = with term<strong>in</strong>al box<br />
E = with encoder<br />
B = with brake<br />
EB = with encoder and brake<br />
Correspond<strong>in</strong>g connect<strong>in</strong>g cable:<br />
Motor: ZKDB9-xx<br />
Encoder: ZK-M12-8-xx<br />
For further <strong>in</strong>formation, see section on "Cables"<br />
AD4118L1804-E 1.8 50.0 1.75 3.3 82 0.45 94 X<br />
Length<br />
"A"<br />
mm<br />
Encoder Brakes<br />
AD4118L1804-B 1.8 50.0 1.75 3.3 82 0.54 114 X<br />
AD4118L1804-EB 1.8 50.0 1.75 3.3 82 0.60 127 X X<br />
D-SUB-9<br />
with D-SUB-9 with D-SUB-9 and M12<br />
Front view and mount<strong>in</strong>g Rear view<br />
Front view and mount<strong>in</strong>g<br />
Rear view<br />
ENCODER M12<br />
P<strong>in</strong> assignment<br />
1 A<br />
2 A\<br />
3 B<br />
4 B\<br />
5 GND<br />
6 I<br />
7 I\<br />
8 Vcc<br />
Hous<strong>in</strong>g GND/shield<strong>in</strong>g<br />
M12 connector<br />
Outl<strong>in</strong>e draw<strong>in</strong>g (<strong>in</strong> mm) AD41 for flange size 42 with 1.8°/full step<br />
40 41<br />
AD4118L1804<br />
AD4118L1804-B<br />
AD4118L1804-E<br />
Side view<br />
Side view<br />
Speed-Torque curves<br />
Top view A<br />
Top view A<br />
AD4118L1804-E<br />
AD4118L1804-EB<br />
Side view<br />
Side view<br />
Top view A<br />
Top view A
Change language