Manual - Holdan.eu

More documents

Recommendations

Info

Power is never totally removed from the unit when it’s plugged into an active AC outlet. Pressing the button at the extreme right on the front panel only places the unit in a powered down mode. This button is a standby switch, not a true off and on switch. Never remove the unit from a cabinet unless the unit has been completely disconnected from AC power. 5.2 Factory Reset For the 10-key programmable front panel: to restore all operational parameters to their original condition, first ensure the unit’s in the operational mode, green power led illuminated (not in Standby red power led illuminated). If it is in the operational mode, hold the standby switch and then hold Buttons “1” and “2” until the unit beeps. For the 48-key front panel: to restore all operational parameters to their original condition, first ensure the unit’s in the operational mode (not in Standby red power led illuminated). If it is in the operational mode, hold in the SHIFT and RESTORE buttons together until the unit beeps multiple times – the first beep indicates that a restore to last-saved settings has occurred, the second that a factory reset has occured. All stored settings except resolutions are lost when the unit is reset. A Firmware update is the only way to perform a complete factory reset 5.3 Initial Operation Check Using Factory Default Settings The C2-7000 series can be operated via the Front Panel Buttons, an LCD display and a Rotary Encoder or multi-directional switch (depending on your front panel version), via a Windows based utility or via a dedicated CORIO® Console hat mimics the operation of a classic video switcher. For the purposes of initially acquainting you with the operation of the unit, this manual will address the operation using the Front Panel controls. Connect the AC power cable to the unit. (Refer to the diagram below. The AC power cable connects to the socket labeled “Power 100v – 240v 47-63Hz” located on the left side of the rear panel as shown.) We’ll be using a Personal Computer for a signal source. Make certain that the monitor resolution can display 1024 x 768 @ 60Hz as this is the default output resolution for the C2-7000 series. Disconnect the cable going from a Personal Computer’s Monitor to the Personal Computer. Connect the output from the PC video card (the PC
connector formerly used by the monitor cable) to the input labeled “DVI- I/RGB1” on the rear panel of the Processor. Next, take the cable from the PC monitor and connect it to the C2-7000 series’ DVI-I/RGB1 output. Then connect the AC Power Cable to a working AC outlet, turn on the PC, monitor and then the C2-7000 series. Provided you have not changed anything from the Factory Defaults and the monitor will display output 1024x768@60Hz and the CORIO® Testcard, by pressing button 3 the monitor will the show the PC’s. If this is the result, the C2-7000 series is passing and processing signals.
Page 1 and 2: C2-7000 SERIES OPERATION MANUAL C2-
Page 3 and 4: C2-7000 SERIES OPERATION MANUAL Tab
Page 5 and 6: C2-7000 SERIES OPERATION MANUAL 12.
Page 7 and 8: 1.0 DISCLAIMER This product is inte
Page 9 and 10: 2.0 IMPORTANT SAFETY INSTRUCTIONS T
Page 11 and 12: 2.0 IMPORTANT: CONSIGNES DE SECURIT
Page 13 and 14: 2.0 INSTRUCCIONES IMPORTANTES DE SE
Page 15 and 16: 2.0 WICHTIGE SICHERHEITSVORSCHRIFTE
Page 17 and 18: 2.0 BELANGRIJKE VEILIGHEIDSINSTRUCT
Page 19 and 20: 3.0 CAPABILITY, TERMS OF REFERENCE
Page 21 and 22: the second output when a ‘Take’
Page 23 and 24: 3.5 Input Sources The C2-7000 serie
Page 25 and 26: Color Background Z (Lock Source) A
Page 27 and 28: From a practical standpoint, this m
Page 29: 5.0 FUNCTIONAL CHECK 5.1 Important
Page 33 and 34: Button Number C2-7100 default C2-72
Page 35 and 36: With these front panels, you can di
Page 37 and 38: 7.0 CHANGING THE OPERATING MODE As
Page 39 and 40: then press button number 1 to toggl
Page 41 and 42: 8.0 MENU TOPOGRAPHY AND ADJUSTMENT
Page 43 and 44: 8.2 Group Names and Descriptions Me
Page 45 and 46: This menu item is only available on
Page 47 and 48: Adjust windows Shrink H/V % [100] [
Page 49 and 50: Adjust keyers Keyer enable [Off] Th
Page 51 and 52: This menu item allows you change wh
Page 53 and 54: Adjust borders Border enable [On] A
Page 55 and 56: This menu item selects the desired
Page 57 and 58: M. Comp Low M. Comp Med. M. Comp Hi
Page 59 and 60: Wipe Size sets the ‘granularity
Page 61 and 62: 8.14 Items associated with the Adju
Page 63 and 64: 800 x 600 60 Hz H/V Start [ 88] x 2
Page 65 and 66: System Autoset sense [Medium] In or
Page 67 and 68: System Fan speed (rpm) 6000 Certain
Page 69 and 70: 10.0 RS232 / IP CONTROL SPECIFICATI
Page 71 and 72: CHA (Channel) SOURCE or MACRO NUMBE
Page 73 and 74: 0x30 = CV1, 0x31 = CV2, 0x32 = CV3
Page 75 and 76: Swap fore / background 144 0..1 = O
Page 77 and 78: H/V start (H) 08B 0..1023 H/V start
Page 79 and 80: Menu text CHA FUNC (Hex) Range of a
Page 81 and 82:
11.0 COMMON OPERATIONS This section
Page 83 and 84:
Decrease V Key Min until reappears,
Page 85 and 86:
The Key Min/Max may need to be read
Page 87 and 88:
Press and hold the macro button (us
Page 89 and 90:
S-curves for left and right project
Page 91 and 92:
For use with dual-channel scalers s
Page 93 and 94:
There is a formula for calculating
Page 95 and 96:
G R R G Too far apart - you need ar
Page 97 and 98:
when you’re trying to output blac
Page 99 and 100:
E.blnd H 640x480 800x600 1024x768 1
Page 101 and 102:
In the Ethernet section be sure to
Page 103 and 104:
13.3 Application menu’s 13.3.1 Fi
Page 105 and 106:
Figure 10 Scripting button screen U
Page 107 and 108:
13.5.2 Loading Logos Figure 13 Logo
Page 109 and 110:
the minimum information of Horizont
Page 111 and 112:
Figure 17 Resolution editor - advan
Page 113 and 114:
14.4 There is excessive flicker on
Page 115 and 116:
15.0 RETURN PROCEDURE Before return
Page 117 and 118:
16.0 WARRANTY POLICY LIMITED WARRAN
Page 119 and 120:
18.0 SPECIFICATION 18.1 Video Input
Page 121:
19.0 CONTACT INFORMATION Should you
show all

Manual - Holdan.eu

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?