Manual - Holdan.eu

More documents

Recommendations

Info

Figure 16 Add resolution to table Once your new resolution is added, you can program the resolution into the Scaler using the Communications menu and then selecting Program into unit and then selecting Program Resolutions. The application will proceed to program all the resolutions on the list into the scaler. Note that this will overwrite any resolutions currently in the scaler. The second method of creating a resolution requires you to know all the detailed timing parameters. The timings tab allows all the detailed video timing information to be added and altered, including the title of the resolution entry (limited to 24 characters). There are also along side the detailed timing parameters several flags that are used to specify the signal type these are interlaced – for interlaced video signals, CCIR for video that would normally be output on CV or YC connectors and RGB for video that would be output on RGB or Component type connections.
Figure 17 Resolution editor - advanced timings In order to modify an existing resolution simply click on the resolution table at the bottom of the screen and it parameters will be editable within the Timings tab. Once the edits are complete click on Update to modify the settings for the selected resolution or Create New to keep the selected resolution and create a new resolution with modified parameters.
Page 1 and 2:
C2-7000 SERIES OPERATION MANUAL C2-
Page 3 and 4:
C2-7000 SERIES OPERATION MANUAL Tab
Page 5 and 6:
C2-7000 SERIES OPERATION MANUAL 12.
Page 7 and 8:
1.0 DISCLAIMER This product is inte
Page 9 and 10:
2.0 IMPORTANT SAFETY INSTRUCTIONS T
Page 11 and 12:
2.0 IMPORTANT: CONSIGNES DE SECURIT
Page 13 and 14:
2.0 INSTRUCCIONES IMPORTANTES DE SE
Page 15 and 16:
2.0 WICHTIGE SICHERHEITSVORSCHRIFTE
Page 17 and 18:
2.0 BELANGRIJKE VEILIGHEIDSINSTRUCT
Page 19 and 20:
3.0 CAPABILITY, TERMS OF REFERENCE
Page 21 and 22:
the second output when a ‘Take’
Page 23 and 24:
3.5 Input Sources The C2-7000 serie
Page 25 and 26:
Color Background Z (Lock Source) A
Page 27 and 28:
From a practical standpoint, this m
Page 29 and 30:
5.0 FUNCTIONAL CHECK 5.1 Important
Page 31 and 32:
connector formerly used by the moni
Page 33 and 34:
Button Number C2-7100 default C2-72
Page 35 and 36:
With these front panels, you can di
Page 37 and 38:
7.0 CHANGING THE OPERATING MODE As
Page 39 and 40:
then press button number 1 to toggl
Page 41 and 42:
8.0 MENU TOPOGRAPHY AND ADJUSTMENT
Page 43 and 44:
8.2 Group Names and Descriptions Me
Page 45 and 46:
This menu item is only available on
Page 47 and 48:
Adjust windows Shrink H/V % [100] [
Page 49 and 50:
Adjust keyers Keyer enable [Off] Th
Page 51 and 52:
This menu item allows you change wh
Page 53 and 54:
Adjust borders Border enable [On] A
Page 55 and 56:
This menu item selects the desired
Page 57 and 58:
M. Comp Low M. Comp Med. M. Comp Hi
Page 59 and 60: Wipe Size sets the ‘granularity
Page 61 and 62: 8.14 Items associated with the Adju
Page 63 and 64: 800 x 600 60 Hz H/V Start [ 88] x 2
Page 65 and 66: System Autoset sense [Medium] In or
Page 67 and 68: System Fan speed (rpm) 6000 Certain
Page 69 and 70: 10.0 RS232 / IP CONTROL SPECIFICATI
Page 71 and 72: CHA (Channel) SOURCE or MACRO NUMBE
Page 73 and 74: 0x30 = CV1, 0x31 = CV2, 0x32 = CV3
Page 75 and 76: Swap fore / background 144 0..1 = O
Page 77 and 78: H/V start (H) 08B 0..1023 H/V start
Page 79 and 80: Menu text CHA FUNC (Hex) Range of a
Page 81 and 82: 11.0 COMMON OPERATIONS This section
Page 83 and 84: Decrease V Key Min until reappears,
Page 85 and 86: The Key Min/Max may need to be read
Page 87 and 88: Press and hold the macro button (us
Page 89 and 90: S-curves for left and right project
Page 91 and 92: For use with dual-channel scalers s
Page 93 and 94: There is a formula for calculating
Page 95 and 96: G R R G Too far apart - you need ar
Page 97 and 98: when you’re trying to output blac
Page 99 and 100: E.blnd H 640x480 800x600 1024x768 1
Page 101 and 102: In the Ethernet section be sure to
Page 103 and 104: 13.3 Application menu’s 13.3.1 Fi
Page 105 and 106: Figure 10 Scripting button screen U
Page 107 and 108: 13.5.2 Loading Logos Figure 13 Logo
Page 109: the minimum information of Horizont
Page 113 and 114: 14.4 There is excessive flicker on
Page 115 and 116: 15.0 RETURN PROCEDURE Before return
Page 117 and 118: 16.0 WARRANTY POLICY LIMITED WARRAN
Page 119 and 120: 18.0 SPECIFICATION 18.1 Video Input
Page 121: 19.0 CONTACT INFORMATION Should you
show all

Manual - Holdan.eu

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?