datavideo SE-900 RS-422/232 Remote Control Protocol - Holdan.eu

More documents

Recommendations

Info

******************************************************* Command code => A0h = CARD_RESET_PARA_CMD Parameter #1 = > 30h=reset current parameter, 31h=reset all user --- Answer --- Parameter #1 = > 30h=reset current parameter, 31h=reset all user ******************************************************* Command code => A2h = CARD_STORE_RECALL_CMD Parameter #1 = > 30h=store, 31h=recall Parameter #2 = > User No.: 31h~33h (3 users) --- Answer --- Parameter #1 = > 30h=store, 31h=recall Parameter #2 = > User No.: 31h~33h (3 users) 34
5.2.3 Analog Video In Board & DV In Board Commands ******************************************************* Command code => 61h = ASK_CARD_TYPE_CMD Parameter #1 = >NC --- Answer --- Parameter #1 =>30h=Analog IN, 31h=DV IN, 32h=SDI IN, 33h=DVI/VGA IN, 34h=Chroma Key BD, 35h=Preview BD, 36h=CG BD, 37h=GenLock BD, 38h=Analog & DV OUT, 39h=SDI OUT, 3Eh=Remote BD, 3Fh=Audio Delay BD, 40h=Tally BD ******************************************************* Command code => 63h = ASK_WORK_STATUS_CMD Parameter #1 = > NC --- Answer --- Parameter #1 = > Card Type: 30h~40h. (Ref. to command 61h) Parameter #2 = > status _flag: (b0=0=off, 1=on); (b1=0=NTSC, 1=PAL); (b4=0=0IRE, 1=7.5IRE); (b5=0=AGC off, 1=AGC on) Parameter #3 = > Input type: 30h=CV in, 31h=YC in, 32h=YUV in, 35h=DV in, 36h=SDI in, 37h=DSUB VGA in, 38h=DVI in Parameter #4 = > Brightness: -99~+99, default=0(80h) Parameter #5 = > Contrast: -99~+99, default=0(80h) Parameter #6 = > Saturation: -99~+99, default=0(80h) Parameter #7 = > NC Parameter #8 = > RGB Correction’s U offset: -99~+99, default=0(80h) Parameter #9 = > RGB Correction’s V offset: -99~+99, default=0(80h) ******************************************************* Command code => 64h = SET_NTSC_PAL_CMD Parameter #1 = > video system: 30h=NTSC, 31h=PAL --- Answer --- Parameter #1 => video system: 30h=NTSC, 31h=PAL ******************************************************* Command code => 65h = ASK_NTSC_PAL_CMD Parameter #1 = > NC --- Answer --- Parameter #1 => video system: 30h=NTSC, 31h=PAL ******************************************************* Command code => 66h = SET_INPUT_TYPE_CMD Parameter #1 = >Set method: 30h=set by parameter #2 directly, 31h=Increase, 32h=Decrease When (para#1=30h) Parameter #2 = >Input type: 30h=CV in, 31h=YC in, 32h=YUV in --- Answer --- Parameter #1 = >Set method: 30h=set by parameter #2 directly, 31h=Increase, 32h=Decrease Parameter #2 = >Input type: 30h=CV in, 31h=YC in, 32h=YUV in, 35
Page 1 and 2: datavideo SE-900 RS-422/232 Remote
Page 3 and 4: 1. Physical layer 1.1 Control I/O f
Page 5 and 6: 3. Application layer The applicatio
Page 7 and 8: 4.1.2.4 parameter-4= current effect
Page 9 and 10: 4.2 The control mode = 01h (NORMAL
Page 11 and 12: 4.2.5 T-bar command 1st 2nd 3rd 4th
Page 13 and 14: 137 = EXT_ASK_GPI_STATUS_CMD 138 =
Page 15 and 16: 4.4.2 The Extension Main Board Comm
Page 17 and 18: ***********************************
Page 19 and 20: 4.4.4 The Extension Main Board Comm
Page 21 and 22: Example: Set the CG mode to interna
Page 23 and 24: ***********************************
Page 25 and 26: 5.0 The Control Command for Extensi
Page 27 and 28: ***********************************
Page 29 and 30: ***********************************
Page 31 and 32: ***********************************
Page 33: 5.2.2 CG Board Command ************
Page 37 and 38: ***********************************
Page 39 and 40: 5.2.4 SDI IN Board Command ********
Page 41 and 42: ***********************************
Page 43 and 44: ***********************************
Page 45 and 46: Example#1: Set the CH5 DVI/VGA IN
Page 47 and 48: ***********************************
Page 49 and 50: 5.2.7 SDI OUT Board Command *******
Page 51 and 52: 5.2.8 PREVIEW Board Command *******
Page 53 and 54: ***********************************
Page 55 and 56: 5.2.9 Audio Delay Board Command ***
Page 57 and 58: ***********************************

datavideo SE-900 RS-422/232 Remote Control Protocol - Holdan.eu

Create successful ePaper yourself

Delete template?

Save as template?