EH12, EH17, EH25 - Small Engine Discount
EH12, EH17, EH25 - Small Engine Discount EH12, EH17, EH25 - Small Engine Discount
ROCKER ARM I L - 14 -
5. 5-1 CAUTIONS 1) Because some mating parts with wear surfaces were machined together when the engine was manifactured, or have established wear patterns during operation, the reassembly of engine parts, is critical to the performance and life expectancy of the engine. MARK AND SORT ALL PARTS SO THAT THEY WILL BE DISASSEMBLED AND INSTALLED IN THEIR ORIGINAL POSITIONS. 2) Crankshaft and camshaft bearings should be cleaned and inspected, and removed only if they appear to be damaged or excessively worn. Remove bearings that are pitted, nicked, burred, discolored, or that rotate roughly or noisily. 3) Keep clean and handle carefully the disassembled parts, Clean them thoroughly with washing oil before the reassembly. 4) Use correct tools in the proper way The use of non-specified tools could cause permanent damage to the engine or components. 5-2 SPECIAL TOOLS Tool No. Tool Use 209 - 95004 - 07 Flywheel puller with bolt For pulling off the flywheel Eli1 7, EH25 Market parts Flywheel puller For pulling off the flywheel EH12 FLYWHEEL PULLER FLYWHEEL PULLER - 15 -
- Page 2 and 3: ROBIN ROBIN AMERICA, INC. ROBIN TO
- Page 4 and 5: " . 13-1 13-2 13-3 13-4 13-5 13-6 1
- Page 6 and 7: ~~~~ ~~ Model TY Pe Bore X Stroke P
- Page 8 and 9: 2. PERFORMANCE 2-1 MAXIMUM OUTPUT A
- Page 10 and 11: n 0 EHf7D, B (. ). for B type " kg-
- Page 12 and 13: 3. FEATURES 1. The overhead valve d
- Page 14 and 15: 4-6 CAMSHAFT ‘I’he camshaft for
- Page 16 and 17: 4-12 IGNITION SYSTEM The ignition s
- Page 20 and 21: 5-3 DISASSEMBLY PROCEDURES Step Par
- Page 22 and 23: ~~ I Step I Part to remove 1 Proced
- Page 24 and 25: Step Part to remove Procedures Rema
- Page 26 and 27: ~ ~~ ~ ~~ ~~~ ~ I Step Part to remo
- Page 28 and 29: ~~ ~ ~~ Step 18 Part to remove 1 Pr
- Page 30 and 31: Step Part to remove 1 Procedures Re
- Page 32 and 33: Step 26 Part to remove Connecting r
- Page 34 and 35: ~~~~ Step Part to remove Procedures
- Page 36 and 37: TOP RING “N” MARK SECOND RlNC O
- Page 38 and 39: 54-5 BALANCER SHAFT (EH25 type only
- Page 40 and 41: Fig. 5-36 (2) Lubricate the oil sea
- Page 42 and 43: (2) Loosen the lock nut on the rock
- Page 44 and 45: (3) Connect the speed control lever
- Page 46 and 47: 5-5 BREAK-IN OPERATION An engine th
- Page 48 and 49: 6-3 WIRING DIAGRAM STANDARD - Ignit
- Page 50 and 51: 8. CARBURETOR 8-1 OPERATION AND CON
- Page 52 and 53: 8-2-4 MAIN SYSTEM (1) Remove the bo
- Page 54 and 55: (4) Remove the reel from the starte
- Page 56 and 57: (6) Test the operation of the recoi
- Page 58 and 59: 10-1-3 IGNlTfON SYSTEM Check the fo
- Page 60 and 61: 11. INSTALLATION Engine life, ease
- Page 62 and 63: ITEM T EH12 T EH17 Unit: mrn (in) S
- Page 64 and 65: ~~ ~~~ ~ Ring groove ITEM side clea
- Page 66 and 67: ITEM T STD EH12 Limit Unit: mrn (in
5.<br />
5-1 CAUTIONS<br />
1) Because some mating parts with wear surfaces were machined together when the engine was<br />
manifactured, or have established wear patterns during operation, the reassembly of engine parts, is<br />
critical to the performance and life expectancy of the engine. MARK AND SORT ALL PARTS SO<br />
THAT THEY WILL BE DISASSEMBLED AND INSTALLED IN THEIR ORIGINAL POSITIONS.<br />
2) Crankshaft and camshaft bearings should be cleaned and inspected, and removed only if they appear<br />
to be damaged or excessively worn. Remove bearings that are pitted, nicked, burred, discolored, or<br />
that rotate roughly or noisily.<br />
3) Keep clean and handle carefully the disassembled parts, Clean them thoroughly with washing oil<br />
before the reassembly.<br />
4) Use correct tools in the proper way<br />
The use of non-specified tools could cause permanent damage to the engine or components.<br />
5-2 SPECIAL TOOLS<br />
Tool No.<br />
Tool<br />
Use<br />
209 - 95004 - 07 Flywheel puller with bolt<br />
For pulling off the flywheel Eli1 7, <strong>EH25</strong><br />
Market parts<br />
Flywheel puller<br />
For pulling off the flywheel <strong>EH12</strong><br />
FLYWHEEL PULLER<br />
FLYWHEEL PULLER<br />
- 15 -
Change language