AL-2021/2041 Operation-Manual GB - Sharp

More documents

Recommendations

Info

7 SPECIAL FUNCTIONS This chapter describes the special functions of this unit. Use these functions as needed. DESCRIPTION OF SPECIAL FUNCTIONS Toner save mode Reduces toner consumption by approximately 10%. Power save modes The unit has two power save modes of operation: preheat mode and auto power shut-off mode. Preheat mode When the unit enters the preheat mode, the power save ( ) indicator will light up and other indicators will remain on or off as before. In this condition, the fuser in the unit is maintained at a lower heat level, thereby saving power. To copy from the preheat mode, make desired copier selections and press the start ( ) key using the normal copying procedure. Auto power shut-off mode When the unit enters the auto power shut-off mode, the power save ( ) indicator will light up and other indicators will go out. The auto power shut-off mode saves more power than the preheat mode but requires a longer time before starting copying. To copy from the auto power shut-off mode, press the start ( ) key. Then make desired copier selections and press the start ( ) key using the normal copying procedure. Auto clear The unit returns to the initial settings a preset amount of time after the end of job. This preset amount of time (auto clear time) can be changed. Resolution of AUTO & MANUAL mode You can set the copy resolution used for AUTO and MANUAL ( ) exposure mode. Prevention of OC copies when the original cover/SPF is up function When enabled, this function may help prevent wasteful use of toner that occurs when the original cover/SPF is not completely closed. If the start ( ) key is pressed when the original cover/SPF is not completely closed, " " will appear in the display and copying may not take place. If copying does not take place, copying can be performed by pressing the start ( ) key again, however, the scan size set in "Copy effective paper width setting function" (program numbers 25, 26) will be used. If the original cover/SPF is completely closed after " " appears, copying will take place at the normal size. 7 64
TONER SAVE MODE 1 Press the exposure mode selector key to select the MANUAL ( ) mode. 2 3 4 Press and hold down the exposure mode selector key for approximately 5 seconds. The MANUAL ( ) indicator will go out and the PHOTO ( ) indicator will begin to blink. The light and dark indicator marked "5" will light up, indicating the standard toner mode is active. To enter the toner save mode, press the light ( ) key. The light and dark indicator marked "1" will light up, indicating the toner save mode is selected. Press the exposure mode selector key. The PHOTO ( ) indicator will stop blinking and light up steadily. The light and dark indicator marked "3" will light up. The toner save mode is now active. To return to the standard mode, repeat the procedure but use the dark ( ) key to select exposure level "5" in step 3. 7 65
Page 1 and 2:
MODEL AL-2021 AL-2041 DIGITAL MULTI
Page 3 and 4:
1 This chapter provides basic infor
Page 5 and 6:
OPERATION PANEL 1 1 2 3 4 5 6 7 Two
Page 7 and 8:
POWER ON Turn the power switch on t
Page 9 and 10:
2 Follow the steps below to load pa
Page 11 and 12:
4 Gently push the paper tray back i
Page 13 and 14: 2 Set the paper guides to the paper
Page 15 and 16: HARDWARE AND SOFTWARE REQUIREMENTS
Page 17 and 18: 8 Click the "MFP Driver" button. Cl
Page 19 and 20: 14 Follow the instructions in the p
Page 21 and 22: 5 Select the printer name (configur
Page 23 and 24: SETTING UP BUTTON MANAGER Button Ma
Page 25 and 26: 4 COPIER FUNCTIONS This chapter exp
Page 27 and 28: Setting a large original (AL-2021)
Page 29 and 30: Automatic exposure adjustment This
Page 31 and 32: TWO SIDED COPYING (AL-2041 only) Tw
Page 33 and 34: SORT COPY Copies of multiple origin
Page 35 and 36: If the memory becomes full • If t
Page 37 and 38: 5 PRINTER FUNCTIONS This chapter ex
Page 39 and 40: Opening the printer driver from the
Page 41 and 42: SETTING ADVANCED PRINT FUNCTIONS Th
Page 43 and 44: 4 Select the actual size of paper t
Page 45 and 46: Printing faint text and lines in bl
Page 47 and 48: Adding a watermark to printed pages
Page 49 and 50: SAVING FREQUENTLY USED PRINT SETTIN
Page 51 and 52: PRINTER DRIVER FEATURES Main Paper
Page 53 and 54: SCANNING USING THE KEYS ON THE MACH
Page 55 and 56: Button Manager settings Once instal
Page 57 and 58: SCANNING FROM YOUR COMPUTER The mac
Page 59 and 60: Scanner driver settings The scanner
Page 61 and 62: Scanning from a WIA-compliant appli
Page 63: 6 7 When scanning ends, the followi
Page 67 and 68: Program No. 25 26 28 29 32 Mode Cop
Page 69 and 70: 8 MAINTENANCE This chapter describe
Page 71 and 72: 4 5 Gently install the TD cartridge
Page 73 and 74: MOVING AND STORING THE UNIT Moving
Page 75 and 76: Problem Possible cause Solution Pag
Page 77 and 78: Problem Cause and solution Page Pri
Page 79 and 80: Problem Cause and solution Page Una
Page 81 and 82: MFP driver cannot be installed (Win
Page 83 and 84: MISFEED REMOVAL When the misfeed (
Page 85 and 86: B: Misfeed in the fusing area 1 Low
Page 87 and 88: D: Misfeed in the SPF (AL-2041) An
Page 89 and 90: A. Information on Disposal for User
Page 91: OPERATION GUIDE EN1 EX1
show all

AL-2021/2041 Operation-Manual GB - Sharp

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?