XG-PH80W-N/X-N Operation-Manual GB

More documents

Recommendations

Info

Maintenance Indicators ■ ■ The warning lights (POWER indicator, TEMP. (temperature warning)/STATUS indicator and LAMP indicator) on the projector indicate problems inside the projector. If a problem occurs, either the TEMP. (temperature warning)/STATUS indicator or the LAMP indicator will illuminate red, and the projector will enter Standby mode. After the projector has entered Standby mode, follow the procedures given below. Top View LAMP (1, 2) indicators TEMP. (temperature warning)/STATUS indicator POWER indicator About the TEMP. (temperature warning)/STATUS indicator If the temperature inside the projector increases, due to blockage of the air vents, or the setting location, the lamp will turn off, the cooling fan will run and then the projector will enter Standby mode, and then the TEMP. (temperature warning)/STATUS indicator will blink. When you fi nd the TEMP. (temperature warning)/STATUS indicator blinking, be sure to perform the measures described on page 65. About the LAMP indicator ■ When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp.(LAMP1/2)” will be displayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp will automatically turn off and then the projector will automatically enter Standby mode. At this time, the lamp indicator will illuminate in red. ■ If you try to turn on the projector a fourth time without replacing the lamp, the projector will not turn on. 64 Indicators on the Projector POWER indicator Red on Normal (Standby) Green on Normal (Power on) Orange blinks Normal (Cooling) Green blinks Normal (Warming up) LAMP indicator Green on Normal (“Eco + Quiet” is “Off”.) Orange on Normal (“Eco + Quiet” is “On”.) Green blinks The lamp is warming up. (“Eco + Quiet” is “Off”.) Orange blinks The lamp is warming up. (“Eco + Quiet” is “On”.) Red on/Red blinks The lamp is shut down abnormally or requires to be changed. (See page 65.) TEMP. Off Normal (temperature Red/Orange Abnormal. (See page 65.) warning)/STATUS blinks indicator
TEMP. (temperature warning)/ STATUS indicator LAMP indicator Maintenance indicator Normal Off Green on (Green blinks when the lamp is warming up.)/ Orange on (Eco) Orange blinks (When the lamp is cooling.) Abnormal Red blinks The TEMP. (temperature warning)/STATUS indicator blinks in red when the projector is on. Red blinks 2 times (Repeatedly) Orange blinks Red blinks Red blinks 2 times (Repeatedly) Red on Problem Cause Possible Solution The internal temperature is abnormally high. The lamp does not illuminate. Time to change the lamp. The lamp does not illuminate. Time to change the lamp. • The lamp unit cover • If the TEMP. (temperature is open. warning)/STATUS indicator blinks in red even when the lamp unit cover are securely installed, contact your nearest Sharp Authorized Projector Dealer or Service Center (see page 76) for advice. • Temperatures • Use the projector in an around the projector area with a temperature of are high. lower than 104°F (+40ºC). • Blocked air intake • Internal circuit failure. • Cooling fan breakdown • Internal circuit failure • Clogged air intake • Relocate the projector to an area with proper ventilation. (See page 8.) • Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center (see page 76) for repair. • No lamp • Install the lamp unit. • Remaining lamp life • Disconnect the power cord becomes 5% or less. from the AC outlet, and then connect it again. • The lamp is shut • Carefully replace the lamp. down abnormally. (See page 66.) • Burnt-out lamp • Lamp circuit failure • The lamp life is over. • Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center (see page 76) for repair. • Please exercise care when replacing the lamp. • Securely install the cover. * For information about other types of blinking, contact your nearest Sharp Authorized Projector Dealer or Service Center (see page 76). Info • If the TEMP. (temperature warning)/STATUS indicator illuminates, and the projector enters Standby mode, follow the possible solutions above and then wait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 10 minutes.) • If the power is turned off for a brief moment due to power outage or some other cause while using the projector, and the power supply recovers immediately after that, the LAMP indicator will illuminate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again. • The cooling fan keeps the internal temperature of the projector constant and this function is controlled automatically. The sound of the cooling fan may change during operation because the fan speed may change and this is not a malfunction. Appendix 65
Page 1 and 2:
DATA PROJECTOR MODEL XG-PH80W-N XG-
Page 3 and 4:
SPECIAL NOTE FOR USERS IN THE U.K.
Page 5 and 6:
Before using the projector, please
Page 7 and 8:
How to Read this Operation Manual
Page 9 and 10:
Adjusting the Projector Function (
Page 11 and 12:
15. Overloading Do not overload wal
Page 13 and 14:
Caution regarding usage of the proj
Page 15 and 16:
Accessories Supplied accessories In
Page 17 and 18: Part Names and Functions Numbers in
Page 19 and 20: Numbers in Z refer to the main page
Page 21 and 22: Easy Start This section shows the b
Page 23 and 24: Setting Up the Projector Video Setu
Page 25 and 26: Connecting the Projector to Other E
Page 27 and 28: Equipment Video equipment, Camera,
Page 29 and 30: When connecting to the LAN terminal
Page 31 and 32: 5 Insert the replacement lens with
Page 33 and 34: Image Projection Shifting the Lens
Page 35 and 36: Adjusting the Focus Press FOCUS +/-
Page 37 and 38: INPUT button (ENTER) button P/R but
Page 39 and 40: Basic Operation RESIZE Output scree
Page 41 and 42: Using the Remote Control to Operate
Page 43 and 44: Useful Features “Signal adjustmen
Page 45 and 46: Using the Menu Screen Adjustment bu
Page 47 and 48: Picture Adjustment (“Picture” M
Page 49 and 50: Menu operation n Page 41 7 Adjustin
Page 51 and 52: Video Adjustment (“Video” Menu)
Page 53 and 54: Adjusting the Projected Image (“S
Page 55 and 56: Menu operation n Page 41 9 Security
Page 57 and 58: Menu operation n Page 41 5 Setting
Page 59 and 60: Useful Features Returning to the De
Page 61 and 62: Useful Features WARNING ■ The fol
Page 63 and 64: Using 3D Viewing Mode Use the follo
Page 65 and 66: Maintenance Cleaning the projector
Page 67: 2 Remove the filter covers. • Rem
Page 71 and 72: Removing and Installing the Lamp Un
Page 73 and 74: Replacing the Color Wheel The proje
Page 75 and 76: Compatibility Chart Computer • Mu
Page 77 and 78: Troubleshooting Problem Check Page
Page 79 and 80: Problem Check Page 3D images fl ick
Page 81 and 82: Specifications Model XG-PH80W-N XG-
Page 83: Index 4:3·············
show all

XG-PH80W-N/X-N Operation-Manual GB

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?