XG-PH80W-N/X-N Operation-Manual GB

More documents

Recommendations

Info

Cleaning and Replacing the Dust Filters When the message shown below is displayed, clean or replace the three dust filters and then reset the filter timer (see page 55). You must clean or replace all three dust filters at the same time to synchronize the filter timer. Clean The Filter. Cleaning the Dust Filters Use a vacuum cleaner to clean dust from the exhaust vent and the intake vent (bottom, side and rear). Info • The dust fi lters should be cleaned every 100 hours of use. Clean the fi lters more often when the projector is used in a dusty or smoky location. • If you want to clean the air vents during projector operation, ensure you press STANDBY/ON on the projector or on the remote control and put the projector into Standby mode. After the cooling fan has stopped, clean the vents. Replacing the Dust Filters STANDBY/ON button Info • If the fi lters become too dirty to clean effectively, purchase new ones (Front: 9NK3243073701, Side: 9NK3243073801, Rear: 9NK3243073601) from your nearest Sharp Authorized Projector Dealer or Service Center. 1 Press STANDBY/ON on the projector or on the remote control to put the projector into standby mode. • Switch the MAIN POWER switch on the projector to “OFF” after the cooling fan stops, and then disconnect the power cord and unplug the power cord from the AC socket. MAIN POWER switch AC socket 62
2 Remove the filter covers. • Remove the fi lter covers towards the direction of the arrow. Front Side Rear 3 Pick the dust filters up and lift them out of all the three filter covers as shown in the figures. 4 Place replacement dust filters and press them down firmly. 5 Replace the filter covers. • Insert the fi lter covers and push them gently as shown in the fi gure. Front Side Rear Appendix 63
Page 1 and 2:
DATA PROJECTOR MODEL XG-PH80W-N XG-
Page 3 and 4:
SPECIAL NOTE FOR USERS IN THE U.K.
Page 5 and 6:
Before using the projector, please
Page 7 and 8:
How to Read this Operation Manual
Page 9 and 10:
Adjusting the Projector Function (
Page 11 and 12:
15. Overloading Do not overload wal
Page 13 and 14:
Caution regarding usage of the proj
Page 15 and 16: Accessories Supplied accessories In
Page 17 and 18: Part Names and Functions Numbers in
Page 19 and 20: Numbers in Z refer to the main page
Page 21 and 22: Easy Start This section shows the b
Page 23 and 24: Setting Up the Projector Video Setu
Page 25 and 26: Connecting the Projector to Other E
Page 27 and 28: Equipment Video equipment, Camera,
Page 29 and 30: When connecting to the LAN terminal
Page 31 and 32: 5 Insert the replacement lens with
Page 33 and 34: Image Projection Shifting the Lens
Page 35 and 36: Adjusting the Focus Press FOCUS +/-
Page 37 and 38: INPUT button (ENTER) button P/R but
Page 39 and 40: Basic Operation RESIZE Output scree
Page 41 and 42: Using the Remote Control to Operate
Page 43 and 44: Useful Features “Signal adjustmen
Page 45 and 46: Using the Menu Screen Adjustment bu
Page 47 and 48: Picture Adjustment (“Picture” M
Page 49 and 50: Menu operation n Page 41 7 Adjustin
Page 51 and 52: Video Adjustment (“Video” Menu)
Page 53 and 54: Adjusting the Projected Image (“S
Page 55 and 56: Menu operation n Page 41 9 Security
Page 57 and 58: Menu operation n Page 41 5 Setting
Page 59 and 60: Useful Features Returning to the De
Page 61 and 62: Useful Features WARNING ■ The fol
Page 63 and 64: Using 3D Viewing Mode Use the follo
Page 65: Maintenance Cleaning the projector
Page 69 and 70: TEMP. (temperature warning)/ STATUS
Page 71 and 72: Removing and Installing the Lamp Un
Page 73 and 74: Replacing the Color Wheel The proje
Page 75 and 76: Compatibility Chart Computer • Mu
Page 77 and 78: Troubleshooting Problem Check Page
Page 79 and 80: Problem Check Page 3D images fl ick
Page 81 and 82: Specifications Model XG-PH80W-N XG-
Page 83: Index 4:3·············
show all

XG-PH80W-N/X-N Operation-Manual GB

Create successful ePaper yourself

Delete template?

Save as template?