PM-Menu-76 Doors - Security Help Desk

More documents

Recommendations

Info

[MENU 7-6] p 2 MODEL 3000 / ACCESS 4000 Programmer’s Manual - Doors. Rev 4.50 D001 Acc.Group-> CARD USER This screen allows the User to assign an Access Group to this Door. The Access Group programming will determine how access works at this Door. D001 Access Group: AG002 D001 Lock Aux: R01:X01 This screen allows an Auxiliary output to be specified that will operate the Door lock associated with this Door. If a Control Module Auxiliary is chosen to operate a Door Lock, the Auxiliary timer units must be set to seconds. For all other Module types the Auxiliary timer is completely independent from the lock open time. (See next screen). Lock Auxiliaries It is recommended that the following Auxiliaries be used as Lock Auxiliaries: Single Door & 2 Door Access Modules: 1st Door Rxx:X01 2nd Door Rxx:X04 LCD Terminal Txx:X01 Intelligent 4 Door Access Module: (Lock Auxiliaries shown must be used) 1st Door Ixx:X01 2nd Door Ixx:X02 3rd Door Ixx:X03 4th Door Ixx:X04 D001 Lock Open Time: 005 S/0.1S This screen determines the time for which this Door will be un-locked during a normal access event. This value is programmable from 0 to 255 Seconds. IMPORTANT NOTES: 1) A value of “000” causes the Door to un-lock indefinitely. The Door must then be re-locked by another operation. (e.g. MENU.9.2, TimeZone, etc.) 2) The Lock Open Timer is independent of the “Auxiliary Timer” for the Lock Auxiliary. Normally, the “Lock Open Time” is the only timer that needs to be programmed for the Lock Auxiliary. However, if any other operation is to be used to momentarily unlock the Door, the Auxiliary Timer [MENU 5,5] for the Lock Auxiliary should also be programmed. (Unless the actual operation already includes a timer). Fast Lock Open Time option. (Only available in Intelligent 4 Door Access Module firmware V1.08 or later.) The “Lock Open Time” defined in Door programming is normally specified in Seconds. e.g. A Lock Open Time of “5”, will activate the Lock Auxiliary for 5 Seconds. In some installations, the Lock Open Time needs to be shorter than 1 second. e.g. When providing a short pulse output to trigger a special access device such as a turnstile system. An option is available to allow an Intelligent 4 Door Access Module to process the “Lock Open Time” as 100 milli-Second increments instead of 1 Second increments. Copyright exists on this manual. Unauthorised copying of this document is prohibited.
MODEL 3000 / ACCESS 4000 Programmer’s Manual - Doors. Rev 4.50 [MENU 7-6] p 3 e.g. -Lock Open Time of “5”, will activate the Lock Aux. for 500 mS. ( 5 x 100mS) -Lock Open Time of “50”, will activate the Lock Aux. for 5 Sec. ( 50 x 100mS) This is done by setting Switch 8 on DIPswitch 2 to the ON position. When set, the Lock Open Time will then be processed as 100 milli-Second increments for all 4 Doors on that particular Module. See the Intelligent 4 Door Access Module installation manual for location of DIPswitch. Only Modules with the DIPswitch set to ON will process the Lock Open Time in this way. Any other Modules with the DIPswitch left in the OFF position, will process the Lock Open Time in the normal manner as 1 second increments. D001 Max. Open Time: 030 sec This screen determines the maximum time this Door may be left open before creating a “Door Open Too Long” (Door Held Open) alarm. The “Door Open Too Long” alarm is a System Input generated from the LCD Terminal or Reader Module associated with the Door. This time is programmable from 1 to 255 seconds. Note: In earlier 2 Door Reader Modules (Part no: 993012) configured for “2” Door mode, the “Maximum Door Open Time” set for the 1st Door on the Module was utilized as the Max. Door Open Time for both Doors. All current Access Modules allow the Max. Door Open time to be defined and operate separately for each Door. i.e. 995012-2 Door Access Modules and Intelligent 4 Door Access Modules. D001 E....... Opts -> nnnnnnnn This screen allows the Installer to programme various Door options. E Extra Area Counting This option allows the User count in the User’s “Extra Area” to be incremented/ decremented when the User is granted access through this door. If the reader is on the “Outside”, the User count is incremented in the User’s Extra Area. 6. Doors If the reader is on the “Inside”, the User count is decremented in the User’s Extra Area. No “count” or “Arm on count = 0” will occur on the Door Areas when this option is enabled. . Spare Spare for future use. This option must be set to “n”. Copyright exists on this manual. Unauthorised copying of this document is prohibited.
Page 1: MODEL 3000 / ACCESS 4000 Programmer
Page 5 and 6: MODEL 3000 / ACCESS 4000 Programmer

PM-Menu-76 Doors - Security Help Desk

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?