Quickview 300 Product Manual PATA - Seagate

More documents

Recommendations

Info

Installation Center Key Slot Pin 1 J1 IDE (40-Pin)/DC (4-Pin) Combination Connector 40-Pin IDE (J1 Section C) Pin 1 4-Pin DC Power (J1 Section A) 4 3 2 1 Pin 40 Pin 42 Pin 44 Figure 3-5 J1 DC Power and PATA Bus Combination Connector 3-10 Quickview 300 80/100/120/160/200/250/300GB PATA
Installation 3.4.1 DC Power (J1, Section A) The recommended mating connectors for the +5 VDC and +12 VDC input power are listed in Table 3-3. Table 3-3 J1 Power Connector, Section A PIN NUMBER VOLTAGE LEVEL MATING CONNECTOR TYPE AND PART NUMBER (OR EQUIVALENT) J1 Section A (4-Pin): 1 +12 VDC 4-Pin Connector: 2 Ground Return for +12 VDC 3 Ground Return for +5 VDC 4 +5 VDC AMP P/N 1-480424-0 Loose piece contacts: AMP P/N VS 60619-4 Strip contacts: AMP P/N VS 61117-4 Note: Labels indicate the pin numbers on the connector. Pins 2 and 3 of section A are the +5 and +12 volt returns and are connected together on the drive. 3.4.2 External Drive Activity LED An external drive activity LED may be connected to the DASP-I/O pin 39 on J1. For more details, see the pin description in Table 5-1. 3.4.3 PATA Bus Interface Connector (J1, Section C) On the Quickview 300 80/100/120/160/200/250/300GB PATA hard disk drives, the PATA bus interface cable connector (J1, section C) is a 40-pin Universal Header, as shown in Figure 3-5. To prevent the possibility of incorrect installation, the connector has been keyed by removing Pin 20. This ensures that a connector cannot be installed upside down. See Chapter 5, “PATA Bus Interface and PATA Commands,” for more detailed information about the required signals. Refer to Table 5-1 for the pin assignments of the PATA bus connector (J1, section C). Quickview 300 80/100/120/160/200/250/300GB PATA 3-11
Page 1 and 2: Maxtor ® Quickview 300 80/100/120/
Page 3 and 4: Maxtor reserves the right to make c
Page 5 and 6: Table of Content Chapter 1 Introduc
Page 7 and 8: Table of Contents Appendix A BREAKI
Page 9 and 10: List of Tables Table 3-1 AT Jumper
Page 11 and 12: Introduction 1.3 MANUAL ORGANIZATIO
Page 13 and 14: Introduction Naming Conventions: 1.
Page 15 and 16: General Description •Emulation of
Page 17 and 18: Chapter 3 INSTALLATION This chapter
Page 19 and 20: Installation Figure 3-2 Quickview 3
Page 21 and 22: Installation The configuration of t
Page 23 and 24: Installation 3.3.1.4 Power On Stand
Page 25: Installation 3.3.2 PATA BUS ADAPTER
Page 29 and 30: Installation Figure 3-7 Mounting Sc
Page 31 and 32: Installation 3.6.1.1 Connecting the
Page 33 and 34: Chapter 4 PRODUCT SPECIFICATIONS 4.
Page 35 and 36: Product Specifications MODELS 80GB
Page 37 and 38: Product Specifications 4.6 Power Mo
Page 39 and 40: Product Specifications Baseplate Te
Page 41 and 42: Product Specifications 4.10 Reliabi
Page 43 and 44: Chapter 5 ATA BUS INTERFACE AND ATA
Page 45 and 46: ATA Bus Interface and ATA Commands
Page 59 and 60: Chapter 6 SERVICE AND SUPPORT 6.1 P
Page 61 and 62: Breaking the 137GB Storage Barrier
Page 63 and 64: Breaking the 137GB Storage Barrier
Page 65 and 66: GLOSSARY A ACCESS - (v) Read, write
Page 67 and 68: Glossary DISK CONTROLLER - A plug-i
Page 69 and 70: Glossary K KILOBYTE (Kb) - A unit o
Page 71 and 72: Glossary REMOVABLE DISK - Generally
Page 73: INDEX A abbreviations 1-1 adapter b

Quickview 300 Product Manual PATA - Seagate

Create successful ePaper yourself

Delete template?

Save as template?