Quickview 300 Product Manual PATA - Seagate

More documents

Recommendations

Info

General Description Versatility • Quiet mode • Power saving modes • Downloadable firmware • Cable select feature • Ability to daisy-chain two drives on the interface 2.3 REGULATORY COMPLIANCE STANDARDS Maxtor Corporation’s disk drive products meet all domestic and international product safety regulatory compliance requirements. Maxtor’s disk drive products conform to the following specifically marked Product Safety Standards: • Underwriters Laboratories (UL) Standard 1950. This certificate is a category certification pertaining to all 3.5-inch series drives models. • Canadian Standards Association (CSA) Standard C.22.2 No. 1950. This certificate is a category certification pertaining to all 3.5-inch series drives models. • TUV Rheinland Standard EN60 950. This certificate is a category certification pertaining to all 3.5-inch series drives models. • This product meets the EC Directive on Waste Electrical and Electronic Equipment (WEEE) and the EC Directive on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS) Product EMI/EMS Qualifications: • CE Mark authorization is granted by TUV Rheinland in compliance with our qualifying under EN 55022:1994 and EN 50082-1:1997. • C-Tick Mark is an Australian authorization marked noted on Maxtor’s disk drive products. The mark proves conformity to the regulatory compliance document AS/NZS 3548: 1995 and BS EN 55022: 1995. • Maxtor’s disk drives are designed as a separate subassembly that conforms to the FCC Rules for Radiated and Conducted emissions, Part 15 Subpart J; Class B when installed in a given computer system. • Approval from Taiwan BSMI. Number: 3892A638 Quickview 300 80/100/120/160/200/250/300GB PATA 2-3
Chapter 3 INSTALLATION This chapter explains how to unpack, configure, mount, and connect the Maxtor Quickview 300 80/100/120/160/200/250/300GB PATA hard disk drive prior to operation. It also explains how to start up and operate the drive. 3.1 SPACE REQUIREMENTS The Quickview 300 hard disk drives are shipped without a faceplate. Figure 3-1 shows the external dimensions of the Quickview 300 PATA drives. Figure 3-1 Mechanical Dimensions of Quickview 300 Hard Disk Drive Quickview 300 80/100/120/160/200/250/300GB PATA 3-1
Page 1 and 2: Maxtor ® Quickview 300 80/100/120/
Page 3 and 4: Maxtor reserves the right to make c
Page 5 and 6: Table of Content Chapter 1 Introduc
Page 7 and 8: Table of Contents Appendix A BREAKI
Page 9 and 10: List of Tables Table 3-1 AT Jumper
Page 11 and 12: Introduction 1.3 MANUAL ORGANIZATIO
Page 13 and 14: Introduction Naming Conventions: 1.
Page 15: General Description •Emulation of
Page 19 and 20: Installation Figure 3-2 Quickview 3
Page 21 and 22: Installation The configuration of t
Page 23 and 24: Installation 3.3.1.4 Power On Stand
Page 25 and 26: Installation 3.3.2 PATA BUS ADAPTER
Page 27 and 28: Installation 3.4.1 DC Power (J1, Se
Page 29 and 30: Installation Figure 3-7 Mounting Sc
Page 31 and 32: Installation 3.6.1.1 Connecting the
Page 33 and 34: Chapter 4 PRODUCT SPECIFICATIONS 4.
Page 35 and 36: Product Specifications MODELS 80GB
Page 37 and 38: Product Specifications 4.6 Power Mo
Page 39 and 40: Product Specifications Baseplate Te
Page 41 and 42: Product Specifications 4.10 Reliabi
Page 43 and 44: Chapter 5 ATA BUS INTERFACE AND ATA
Page 45 and 46: ATA Bus Interface and ATA Commands
Page 59 and 60: Chapter 6 SERVICE AND SUPPORT 6.1 P
Page 61 and 62: Breaking the 137GB Storage Barrier
Page 63 and 64: Breaking the 137GB Storage Barrier
Page 65 and 66: GLOSSARY A ACCESS - (v) Read, write
Page 67 and 68:
Glossary DISK CONTROLLER - A plug-i
Page 69 and 70:
Glossary K KILOBYTE (Kb) - A unit o
Page 71 and 72:
Glossary REMOVABLE DISK - Generally
Page 73:
INDEX A abbreviations 1-1 adapter b
show all

Quickview 300 Product Manual PATA - Seagate

Create successful ePaper yourself

Delete template?

Save as template?