USER MANUAL SWAN Cycle III version 40.72A

More documents

Recommendations

Info

viii
Chapter 1 Introduction The information about the SWAN package is distributed over five different documents. This User Manual describes the complete input and usage of the SWAN package. The Implementation Manual explains the installation procedure of SWAN on a single- or multiprocessor machine with shared or distributed memory. The System documentation outlines the internals of the program and discusses program maintenance. The Programming rules is meant for programmers who want to develop SWAN. The Scientific/Technical documentation discusses the physical and mathematical details and the discretizations that are used in the SWAN program. The mapping of these numerical techniques in SWAN code is also discussed. In Chapter 2 some general definitions and remarks concerning the usage of SWAN, the treatment of grids, boundary conditions, etc. is given. It is advised to read these definitions and remarks before consulting the rest of the manual. Chapter 3 gives some remarks concerning the input and output files of SWAN. Chapter 4 describes the complete set of commands of the program SWAN. It is strongly advised that users who are not so experienced in the use of SWAN first read Chapters 2 and 3. This Manual also contains some appendices. In Appendix A definitions of several output parameters are given. Appendix B outlines the syntax of the command file (or input file). A complete set of all the commands use in SWAN can be found in Appendix C. Appendix D described the format of the files for spectral input and output by SWAN. 1
Page 1: SWAN USER MANUAL SWAN Cycle III ver
Page 5 and 6: Contents 1 Introduction 1 2 General
Page 7: TABLE . . . . . . . . . . . . . . .
Page 11 and 12: Chapter 2 General definitions and r
Page 13 and 14: General definitions and remarks 5 r
Page 15 and 16: General definitions and remarks 7 I
Page 17 and 18: which SWAN performs the computation
Page 19 and 20: General definitions and remarks 11
Page 27 and 28: Chapter 3 Input and output files 3.
Page 29 and 30: Chapter 4 Description of commands 4
Page 31 and 32: (h) Commands to write or plot outpu
Page 33 and 34: Description of commands 25 ’name
Page 35 and 36: Description of commands 27 Default:
Page 37 and 38: Description of commands 29 mesh. Th
Page 39 and 40: ⎛ ∆f = ⎝−1 + Description of
Page 41 and 42: Description of commands 33 • Easy
Page 43 and 44: Description of commands 35 grids ca
Page 45 and 46: Description of commands 37 y ′
Page 47 and 48: Description of commands 39 [fac]
Page 49 and 50: Description of commands 41 ’(10X,
Page 51 and 52: Description of commands 43 | | East
Page 53 and 54: Description of commands 45 CONSTANT
Page 55 and 56: Description of commands 47 points o
Page 57 and 58: Description of commands 49 CRAY WKS
Page 59 and 60:
Description of commands 51 This com
Page 61 and 62:
Description of commands 53 | JANSse
Page 63 and 64:
Description of commands 55 [Csh3] c
Page 65 and 66:
Description of commands 57 [ursell]
Page 67 and 68:
Description of commands 59 [slope]
Page 69 and 70:
Description of commands 61 [cgmod]
Page 71 and 72:
Description of commands 63 < > [lim
Page 73 and 74:
Description of commands 65 SIGIMPL
Page 75 and 76:
Description of commands 67 ’sname
Page 77 and 78:
Description of commands 69 (see bel
Page 79 and 80:
Description of commands 71 [alpn] d
Page 81 and 82:
Description of commands 73 ‘long
Page 83 and 84:
| HSign | | | | HSWEll | | | | DIR
Page 85 and 86:
Description of commands 77 | WLENgt
Page 87 and 88:
Description of commands 79 QP DEPTH
Page 89 and 90:
Description of commands 81 [tbegblk
Page 91 and 92:
Description of commands 83 OUTput [
Page 93 and 94:
Description of commands 85 If SWAN
Page 95 and 96:
Description of commands 87 ACCUR MX
Page 97 and 98:
Appendix A Definitions of variables
Page 99 and 100:
Definitions of variables 91 RPER co
Page 101 and 102:
Definitions of variables 93 WLEN Th
Page 103 and 104:
Appendix B Command syntax B.1 Comma
Page 105 and 106:
Repetitions of keywords and/or othe
Page 107 and 108:
Required data and optional data Com
Page 109 and 110:
Appendix C File swan.edt Below the
Page 111 and 112:
File swan.edt 103 ! | -> DEFault !
Page 113 and 114:
File swan.edt 105 ! FRAME ’sname
Page 115 and 116:
Appendix D Spectrum files, input an
Page 117 and 118:
0.3892E-03 192.0 15.2 0.8007E-03 24
Page 119 and 120:
Spectrum files, input and output 11
Page 121 and 122:
Spectrum files, input and output 11
Page 123 and 124:
Bibliography [1] SWAN - Implementat
Page 125:
117 longitude, 8, 27, 49, 50, 85, 1
show all

USER MANUAL SWAN Cycle III version 40.72A

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?