USER MANUAL SWAN Cycle III version 40.72A
USER MANUAL SWAN Cycle III version 40.72A USER MANUAL SWAN Cycle III version 40.72A
76 Chapter 4 | | | WIND | | | | PROPAgat | | | | PROPXy | | | | PROPTheta | | | | PROPSigma | | | | GENErat | | -> Sec | < < > [unit] > (OUTput [tbegblk] [deltblk]) < MIn > | GENWind | | HR | | | | DAy | | REDIst | | | | REDQuad | | | | REDTriad | | | | DISSip | | | | DISBot | | | | DISSUrf | | | | DISWcap | | | | RADStr | | | | QB | | | | TRAnsp | | | | FORce | | | | UBOT | | | | URMS | | | | TMBOT | | |
Description of commands 77 | WLENgth | | | | STEEpness | | | | BFI | | | | DHSign | | | | DRTM01 | | | | LEAK | | | | TIME | | | | TSEC | | | | XP | | | | YP | | | | DIST | | | | SETUP | CANNOT BE USED IN 1D-MODE. With this optional command the user indicates that one or more spatial distributions should be written to a file. ’sname’ HEADER NOHEADER ’fname’ name of frame or group (see commands FRAME or GROUP) with this option the user indicates that the output should be written to a file with header lines. The text of the header indicates run identification (see command PROJECT), time, frame name or group name (’sname’), variable and unit. The number of header lines is 8. Note: the numerical values in the file are in the units indicated in the header. with this option the user indicates that the output should be written to a file without header lines. name of the data file where the output is to be written to. Default for option HEADER is the PRINT file. In case of NOHEADER the filename is required. Note that when the extension is ‘.mat’, a binary MATLAB file will be generated automatically. This file requires less space on your computer and can be loaded in MATLAB much faster than the ASCII-file. Binary MATLAB files are particularly useful for the computation with
- Page 33 and 34: Description of commands 25 ’name
- Page 35 and 36: Description of commands 27 Default:
- Page 37 and 38: Description of commands 29 mesh. Th
- Page 39 and 40: ⎛ ∆f = ⎝−1 + Description of
- Page 41 and 42: Description of commands 33 • Easy
- Page 43 and 44: Description of commands 35 grids ca
- Page 45 and 46: Description of commands 37 y ′
- Page 47 and 48: Description of commands 39 [fac]
- Page 49 and 50: Description of commands 41 ’(10X,
- Page 51 and 52: Description of commands 43 | | East
- Page 53 and 54: Description of commands 45 CONSTANT
- Page 55 and 56: Description of commands 47 points o
- Page 57 and 58: Description of commands 49 CRAY WKS
- Page 59 and 60: Description of commands 51 This com
- Page 61 and 62: Description of commands 53 | JANSse
- Page 63 and 64: Description of commands 55 [Csh3] c
- Page 65 and 66: Description of commands 57 [ursell]
- Page 67 and 68: Description of commands 59 [slope]
- Page 69 and 70: Description of commands 61 [cgmod]
- Page 71 and 72: Description of commands 63 < > [lim
- Page 73 and 74: Description of commands 65 SIGIMPL
- Page 75 and 76: Description of commands 67 ’sname
- Page 77 and 78: Description of commands 69 (see bel
- Page 79 and 80: Description of commands 71 [alpn] d
- Page 81 and 82: Description of commands 73 ‘long
- Page 83: | HSign | | | | HSWEll | | | | DIR
- Page 87 and 88: Description of commands 79 QP DEPTH
- Page 89 and 90: Description of commands 81 [tbegblk
- Page 91 and 92: Description of commands 83 OUTput [
- Page 93 and 94: Description of commands 85 If SWAN
- Page 95 and 96: Description of commands 87 ACCUR MX
- Page 97 and 98: Appendix A Definitions of variables
- Page 99 and 100: Definitions of variables 91 RPER co
- Page 101 and 102: Definitions of variables 93 WLEN Th
- Page 103 and 104: Appendix B Command syntax B.1 Comma
- Page 105 and 106: Repetitions of keywords and/or othe
- Page 107 and 108: Required data and optional data Com
- Page 109 and 110: Appendix C File swan.edt Below the
- Page 111 and 112: File swan.edt 103 ! | -> DEFault !
- Page 113 and 114: File swan.edt 105 ! FRAME ’sname
- Page 115 and 116: Appendix D Spectrum files, input an
- Page 117 and 118: 0.3892E-03 192.0 15.2 0.8007E-03 24
- Page 119 and 120: Spectrum files, input and output 11
- Page 121 and 122: Spectrum files, input and output 11
- Page 123 and 124: Bibliography [1] SWAN - Implementat
- Page 125: 117 longitude, 8, 27, 49, 50, 85, 1
76 Chapter 4<br />
| |<br />
| WIND |<br />
| |<br />
| PROPAgat |<br />
| |<br />
| PROPXy |<br />
| |<br />
| PROPTheta |<br />
| |<br />
| PROPSigma |<br />
| |<br />
| GENErat | | -> Sec |<br />
< < > [unit] > (OUTput [tbegblk] [deltblk]) < MIn ><br />
| GENWind | | HR |<br />
| | | DAy |<br />
| REDIst |<br />
| |<br />
| REDQuad |<br />
| |<br />
| REDTriad |<br />
| |<br />
| DISSip |<br />
| |<br />
| DISBot |<br />
| |<br />
| DISSUrf |<br />
| |<br />
| DISWcap |<br />
| |<br />
| RADStr |<br />
| |<br />
| QB |<br />
| |<br />
| TRAnsp |<br />
| |<br />
| FORce |<br />
| |<br />
| UBOT |<br />
| |<br />
| URMS |<br />
| |<br />
| TMBOT |<br />
| |