- Page 1: SWAN USER MANUAL SWAN Cycle III ver
- Page 5 and 6: Contents 1 Introduction 1 2 General
- Page 7: TABLE . . . . . . . . . . . . . . .
- Page 11 and 12: Chapter 2 General definitions and r
- Page 13 and 14: General definitions and remarks 5 r
- Page 15 and 16: General definitions and remarks 7 I
- Page 17 and 18: which SWAN performs the computation
- Page 19 and 20: General definitions and remarks 11
- Page 21 and 22: General definitions and remarks 13
- Page 23 and 24: General definitions and remarks 15
- Page 25 and 26: General definitions and remarks 17
- Page 27 and 28: Chapter 3 Input and output files 3.
- Page 29 and 30: Chapter 4 Description of commands 4
- Page 31 and 32: (h) Commands to write or plot outpu
- Page 33 and 34: Description of commands 25 ’name
- Page 35 and 36: Description of commands 27 Default:
- Page 37 and 38: Description of commands 29 mesh. Th
- Page 39 and 40: ⎛ ∆f = ⎝−1 + Description of
- Page 41 and 42: Description of commands 33 • Easy
- Page 43 and 44: Description of commands 35 grids ca
- Page 45 and 46: Description of commands 37 y ′
- Page 47 and 48: Description of commands 39 [fac]
- Page 49 and 50: Description of commands 41 ’(10X,
- Page 51 and 52: Description of commands 43 | | East
- Page 53 and 54: Description of commands 45 CONSTANT
- Page 55 and 56: Description of commands 47 points o
- Page 57 and 58: Description of commands 49 CRAY WKS
- Page 59 and 60:
Description of commands 51 This com
- Page 61 and 62:
Description of commands 53 | JANSse
- Page 63 and 64:
Description of commands 55 [Csh3] c
- Page 65 and 66:
Description of commands 57 [ursell]
- Page 67 and 68:
Description of commands 59 [slope]
- Page 69 and 70:
Description of commands 61 [cgmod]
- Page 71 and 72:
Description of commands 63 < > [lim
- Page 73 and 74:
Description of commands 65 SIGIMPL
- Page 75 and 76:
Description of commands 67 ’sname
- Page 77 and 78:
Description of commands 69 (see bel
- Page 79 and 80:
Description of commands 71 [alpn] d
- Page 81 and 82:
Description of commands 73 ‘long
- Page 83 and 84:
| HSign | | | | HSWEll | | | | DIR
- Page 85 and 86:
Description of commands 77 | WLENgt
- Page 87 and 88:
Description of commands 79 QP DEPTH
- Page 89 and 90:
Description of commands 81 [tbegblk
- Page 91 and 92:
Description of commands 83 OUTput [
- Page 93 and 94:
Description of commands 85 If SWAN
- Page 95 and 96:
Description of commands 87 ACCUR MX
- Page 97 and 98:
Appendix A Definitions of variables
- Page 99 and 100:
Definitions of variables 91 RPER co
- Page 101 and 102:
Definitions of variables 93 WLEN Th
- Page 103 and 104:
Appendix B Command syntax B.1 Comma
- Page 105 and 106:
Repetitions of keywords and/or othe
- Page 107 and 108:
Required data and optional data Com
- Page 109 and 110:
Appendix C File swan.edt Below the
- Page 111 and 112:
File swan.edt 103 ! | -> DEFault !
- Page 113 and 114:
File swan.edt 105 ! FRAME ’sname
- Page 115 and 116:
Appendix D Spectrum files, input an
- Page 117 and 118:
0.3892E-03 192.0 15.2 0.8007E-03 24
- Page 119 and 120:
Spectrum files, input and output 11
- Page 121 and 122:
Spectrum files, input and output 11
- Page 123 and 124:
Bibliography [1] SWAN - Implementat
- Page 125:
117 longitude, 8, 27, 49, 50, 85, 1