USER MANUAL SWAN Cycle III version 40.72A

More documents

Recommendations

Info

114
Bibliography [1] SWAN – Implementation manual. Delft University of Technology, Environmental Fluid Mechanics Section, available from http://www.fluidmechanics.tudelft.nl/swan/index.htm (Version 40.72, May 2008). [2] SWAN – Programming rules. Delft University of Technology, Environmental Fluid Mechanics Section, available from http://www.fluidmechanics.tudelft.nl/swan/index.htm (Version 1.3, August 2006). [3] SWAN – System documentation. Delft University of Technology, Environmental Fluid Mechanics Section, to be available. [4] SWAN – Scientific and Technical documentation. Delft University of Technology, Environmental Fluid Mechanics Section, available from http://www.fluidmechanics.tudelft.nl/swan/index.htm (Version 40.72A, October 2008). 115
Page 1:
SWAN USER MANUAL SWAN Cycle III ver
Page 5 and 6:
Contents 1 Introduction 1 2 General
Page 7 and 8:
TABLE . . . . . . . . . . . . . . .
Page 9 and 10:
Chapter 1 Introduction The informat
Page 11 and 12:
Chapter 2 General definitions and r
Page 13 and 14:
General definitions and remarks 5 r
Page 15 and 16:
General definitions and remarks 7 I
Page 17 and 18:
which SWAN performs the computation
Page 19 and 20:
General definitions and remarks 11
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Chapter 3 Input and output files 3.
Page 29 and 30:
Chapter 4 Description of commands 4
Page 31 and 32:
(h) Commands to write or plot outpu
Page 33 and 34:
Description of commands 25 ’name
Page 35 and 36:
Description of commands 27 Default:
Page 37 and 38:
Description of commands 29 mesh. Th
Page 39 and 40:
⎛ ∆f = ⎝−1 + Description of
Page 41 and 42:
Description of commands 33 • Easy
Page 43 and 44:
Description of commands 35 grids ca
Page 45 and 46:
Description of commands 37 y ′
Page 47 and 48:
Description of commands 39 [fac]
Page 49 and 50:
Description of commands 41 ’(10X,
Page 51 and 52:
Description of commands 43 | | East
Page 53 and 54:
Description of commands 45 CONSTANT
Page 55 and 56:
Description of commands 47 points o
Page 57 and 58:
Description of commands 49 CRAY WKS
Page 59 and 60:
Description of commands 51 This com
Page 61 and 62:
Description of commands 53 | JANSse
Page 63 and 64:
Description of commands 55 [Csh3] c
Page 65 and 66:
Description of commands 57 [ursell]
Page 67 and 68:
Description of commands 59 [slope]
Page 69 and 70:
Description of commands 61 [cgmod]
Page 71 and 72: Description of commands 63 < > [lim
Page 73 and 74: Description of commands 65 SIGIMPL
Page 75 and 76: Description of commands 67 ’sname
Page 77 and 78: Description of commands 69 (see bel
Page 79 and 80: Description of commands 71 [alpn] d
Page 81 and 82: Description of commands 73 ‘long
Page 83 and 84: | HSign | | | | HSWEll | | | | DIR
Page 85 and 86: Description of commands 77 | WLENgt
Page 87 and 88: Description of commands 79 QP DEPTH
Page 89 and 90: Description of commands 81 [tbegblk
Page 91 and 92: Description of commands 83 OUTput [
Page 93 and 94: Description of commands 85 If SWAN
Page 95 and 96: Description of commands 87 ACCUR MX
Page 97 and 98: Appendix A Definitions of variables
Page 99 and 100: Definitions of variables 91 RPER co
Page 101 and 102: Definitions of variables 93 WLEN Th
Page 103 and 104: Appendix B Command syntax B.1 Comma
Page 105 and 106: Repetitions of keywords and/or othe
Page 107 and 108: Required data and optional data Com
Page 109 and 110: Appendix C File swan.edt Below the
Page 111 and 112: File swan.edt 103 ! | -> DEFault !
Page 113 and 114: File swan.edt 105 ! FRAME ’sname
Page 115 and 116: Appendix D Spectrum files, input an
Page 117 and 118: 0.3892E-03 192.0 15.2 0.8007E-03 24
Page 119 and 120: Spectrum files, input and output 11
Page 121: Spectrum files, input and output 11
Page 125: 117 longitude, 8, 27, 49, 50, 85, 1
show all

USER MANUAL SWAN Cycle III version 40.72A

Create successful ePaper yourself

Delete template?

Save as template?