5-PHASE STEPPING SYSTEMS - sanyo denki europe

More documents

Recommendations

Info

DC input Set modelMicro step DC input Set model Micro step Set Model Configuration P.36 SpecificationsCharacteristics P.38 to 52 Motor specifications P.53Driver specifications P.54 Motor dimensions P.97 to 104Driver dimensions P.105 Features The auto-micro function provides low vibration and smooth drive even with coarse resolution setting of one or two divisions (full-/ half-step), and supports micro steps of 250 divisions. High precision current detection reduces speed fluctuations by 50% compared with former model. Model No.: F5PAE140P100. Our conventional product Model No.: PMDPC1S3P01 Set model configuration items Driver Model numberF5PAE140P100Power supplyDC24V/48V Motor Motor size 28mm sq. (1.10inch sq.), 42mm sq. (1.65inch sq.), 60mm sq. (2.36inch sq.), 86mm. ( 3.39inch) Cables with connectors Power supply, Input/output signal, Motor (1m each) Instruction manuals can be downloaded from our website. System configuration Motor End cap side Electromagnetic brake Encoder (option) Host Devices PLC, etc. I/O signal cable (Set model configuration items) Flange side Spur gear Low-backlash gear Harmonic gear Brake power source DC24V Required for brakeequipped stepping motor models. Motor cable (Set model configuration items) Driver Pulse signal Regeneration resistor Model number FFE-01 (Optional Accessories) Connect the regenerative resistor when there is a risk that the supply voltage could exceed 60 V DC due to the motor's back emf. Power supply cable (Set model configuration items) AC power source Single phase 100V to 230V Molded case circuit breaker Electromagnetic contactor Noise filter Switching power supply DC power source 24V/48V Protects the power line. Cuts off circuit in the event of overcurrent. Switches driver power on/off. Use together with a surge protector. Filters out incoming noise from power line. Converts AC power to DC power. 34
Model number convention Example: The model number of the set with a DC input micro-step driver and motor model 103F7851-82CXA4 is composed as follows. This motor is specified as 60mm sq. (2.36inch sq.) and 92mm (3,62inch) long (motor + gear), single shaft, with low backlash gears. AC input Set model Micro step FA F 78 1 S - CX 3.6 Gear ratio 3.6 to 100 DC input Set model Micro step CXLow-backlash gear model GXSpur gear model HXHarmonic gear model XBElectromagnetic brake model DC input Set model Full / half step Stepping motor shaft spec SSingle shaftDDouble shaft Stepping motor total length (This is the standard model case. See the dimensions page for models with gears and electromagnetic brake.) Stepping Motor Code Motor size 28mm sq. (1.10inch sq.) 42mm sq. (1.65inch sq.) 60mm sq. (2.36inch sq.) 86mm ( 3.39inch ) Motor model Motor length : Motor model Motor length : Motor model Motor length : Motor model Motor length : number mminch number mminch number mminch number mminch 1 SH5281 32 (1.26) 103F5505 34 (1.34) 103F7851 46.5 (1.83) 103F8581 62.15 (2.45) 2 103F5508 40 (1.57) 103F7852 55 (2.17) 103F8582 92.2 (3.63) 3 103F7853 87.5 (3.44) 4 103F5510 49 (1.93) 5 SH5285 51.5 (2.03) Linear Actuator Stepping Motor Stepping motor size 5228mm sq. (1.10inch sq.)7860mm sq. (2.36inch sq.) 5542mm sq. (1.65inch sq.)85 86mm ( 3.39inch sq.) Stepping motor series name FFSH series motor Stepping motor for vacuum environment FADC input DC24V/48V microstep Dimensions 35
Page 1 and 2: 5-PHASE STEPPING SYSTEMS Ver.5
Page 3 and 4: Index Features P. 4 Line Up P. 5 Li
Page 5 and 6: Line up Motor/driver sets are conve
Page 7 and 8: Stepping MotorP.84 - Connection Met
Page 9 and 10: Model number convention Example: Th
Page 11 and 12: Connector Set - Housing/Contact Lis
Page 13 and 14: Motor size 60mm sq. (2.36inch sq.)
Page 15 and 16: CE / UL model AC input DriverModel
Page 17 and 18: Motor size 86mm ( 3.39inch) 106m
Page 21 and 22: Motor size Motor + gear length 127.
Page 23 and 24: Harmonic gear model AC input Driver
Page 25 and 26: Electromagnetic brake model AC inpu
Page 27 and 28: Motor size Motor + brake length 180
Page 29 and 30: Driver specifications General spec
Page 31 and 32: Connections and Signals External w
Page 33: Input circuit configuration of PD,
Page 37 and 38: Cables with connectorsIncluded in a
Page 41 and 42: Low-backlash gear model DC input Dr
Page 43 and 44: 60mm sq. (2.36inch sq.) Motor size
Page 47 and 48: 28mm sq. (1.10inch sq.) Motor size
Page 51 and 52: Electromagnetic brake model DC inpu
Page 53 and 54: Motor specifications General speci
Page 55 and 56: Driver Controls and Connectors 2 Fu
Page 57 and 58: Input circuit configuration of CW (
Page 59 and 60: Dimensions Stepping motor for vacuu
Page 61 and 62: Model number convention Example: Th
Page 63 and 64: Standard model DC input DriverModel
Page 65 and 66: Motor size 86mm ( 3.39inch) Motor
Page 71 and 72: Spur gear model DC input DriverMode
Page 73 and 74: Harmonic gear model DC input Driver
Page 79 and 80: Driver specifications General spec
Page 81 and 82: Connections and Signals External w
Page 83 and 84: Input circuit configuration of PD
Page 85 and 86:
60mm ( 2.36inch) AC input Set mode
Page 87 and 88:
42mm sq. (1.65inch sq.) 0.72/step M
Page 89 and 90:
60mm sq. (2.36inch sq.) 0.72/step M
Page 91 and 92:
86mm ( 3.39inch) 0.72/step Motor w
Page 93 and 94:
Allowable radial / thrust load Radi
Page 95 and 96:
Linear Actuator Stepping Motor Line
Page 97 and 98:
Dimensions Stepping motor dimension
Page 99 and 100:
Set model configuration motor (stan
Page 101 and 102:
Set model configuration motor (Low-
Page 103 and 104:
Set model configuration motor (Harm
Page 105 and 106:
Stepping motor dimensions[Unit : mm
Page 107 and 108:
Safety Consideration The drivers an
Page 109 and 110:
Inquiry Check Sheet For more inform
Page 111 and 112:
MEMO
show all

5-PHASE STEPPING SYSTEMS - sanyo denki europe

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?