5-PHASE STEPPING SYSTEMS - sanyo denki europe

More documents

Recommendations

Info

AC input Set modelMicro step Motor specifications General specifications Model number 103F55 103F785 103F858 103F8958 103M55 103M785 103M858 103M8958 Specification type S1 (continuous operation) Ambient operation temperature 10 to 50 (0 to 40 for harmonic gear model) 10 to 40 Storage temperature 20 to 65 20 to 60 Ambient operation 20 to 90 RH (no condensation) humidity 95 RH Max.: Under 40, 57 RH Max.: Under 50, 35 RH Max.: Under 60 (no condensation) Storage humidity 5 to 95 RH (no condensation) Operation altitude 1000 m (3280 feet) MAX. above sea level 1000 m (3280 feet) MAX. above sea level Vibration resistance Vibration frequency 10 to 500 Hz, total amplitude 1.52 mm (10 to 70 Hz), vibration acceleration 147 m/s2 (70 to 500 Hz), sweep time 15 min/cycle, 12 sweeps in each X, Y and Z direction. Impact resistance 490m/s 2 of acceleration for 11 ms with half-sine wave applying three times for X, Y, and Z axes each, 18 times in total. Insulation class Class B ( 130 ) Class B ( 130 ) [UL class A ( 105 )] Withstand voltage At normal ambient temperature and humidity, no failure with 1500 V AC @50/60 Hz applied for one minute between motor winding and frame. Insulation resistance Protection grade Wiringtemperature increase Axial play (Note1) Radial play (Note2) At normal ambient temperature and humidity, 100 Mohm or more on megger with 500 V DC between motor winding and frame. IP40 80K MAX. (Based on Sanyo Denki standard) 0.075mm (0.002952inch) MAX., Load 4.4N (1lbs) 0.075mm (0.002952inch) MAX., Load 9N (2lbs) 0.025mm (0.00098inch) MAX., Load 4.4N (1lbs) 0.075mm (0.002952inch) MAX., Load 9N (2lbs) 80K MAX. (Based on Sanyo Denki standard) 0.075mm (0.002952inch) MAX., Load 9N (2lbs) 0.025mm (0.00098inch)MAX., Load 4.4N (1lbs) 0.075mm (0.002952inch) MAX., Load 9N (2lbs) 0.025mm (0.00098inch) MAX., Load 4.4N (1lbs) Shaft runout 0.025mm 0.025mm 0.05mm 0.025mm 0.05mm Inserted part concentricity 0.05mm against shaft 0.075mm 0.075mm 0.075mm 0.075mm Fitted surface angularity 0.1mm against shaft 0.1mm 0.1mm 0.1mm 0.1mm (Note1) Axial play: Shaft displacement under axial load. (Note2) Radial play: Shaft displacement under radial load applied 1/3rd of the length from the end of the shaft. Safety standardsType code103M55 /103M785 /103M858 /103M8958 (CE / UL model) CE Directives Standard part Low-voltage directives EN-60034-1, IEC34-5, (EN-60034-5) Acquired standards Standard part File No. UL UL UL for Canada (c-UL) UL1004, UL2111 E208878 Internal wire connection Connection Method: Pentagon Black Blue Red Yellow Orange Direction of motor rotate The direction of motor rotate is counterclockwise when viewed from the output shaft side at the direct current energization in the following order. This is an instance of the standard model, the electromagnetic brake model and the CE / UL model. As for some of the models with the gear, the direction of motor rotation is different, please make inquiries. 28 Color of leads Exciting order 1 2 3 4 5 6 7 8 9 10 Black Red Orange Yellow Blue
Driver specifications General specifications Basic specifications Functions Signal Model number Power supply Source current Protection class Environment Operation environment Ambient operation temperature Storage temperature Ambient operation humidity Storage humidity Operation altitude Vibration resistance Impact resistance Withstand voltage Insulation resistance Mass Protection functions FS1W075P00 Single phase AC100V to 230V 10 15%50/60Hz 4A Max. Class Installation category (over-voltage category) (CE)Pollution level2 0 to 50 20 to 70 35 to 85%RH (no condensation) 10 to 90%RH (no condensation) 1000 m (3280 feet) MAX. above sea level Tested under the following conditions ; 5m/s 2 , frequency range 10 to 55Hz, direction along X, Y and Z axes, for 2 hours each Not influenced at NDS-C-0110 standard section 3.2.2 divisionC. Not influenced when 1500V AC is applied between power input terminal and cabinet for one minute. 10M ohm MIN. when measured with 500V DC megohmmeter between input terminal and cabinet. 0.8kg Driver overheating, main circuit power supply error, and over-current Electric power monitor, phase origin monitor, pulse monitor, alarm indications (overcurrent, overheating LED indication protection, supply under- and overvoltage, hardware fault, motor disconnection or non-standard motor connection) Input signal Photo-coupler input system ; input resistance: 220 ; input-signalHlevel : 4.0 to 5.5V ; input-signalLlevel : 0 to 0.5V Output signal From the photo coupler by the open collector output Output specification : Vceo = 30V MAX., Ic = 5mA Safety standards CE (TÜV) UL Directives Category Standard part Name Low-voltage directives EN50178 EMC directives Acquired standards UL UL for Canada (c-UL) Emission Immunity EN55011-A EN55011-A Terminal disturbance voltage Electromagnetic radiation disturbance EN61000-4-2 ESD (Electrostatic discharge) EN61000-4-3 RS (Radio-frequency amplitude modulated electromagnetic field) EN61000-4-4 Fast transionts EN61000-4-6 Surges EN61000-4-5 CS (Radio-frequency common mode) EN61000-4-11 Voltage dips, Voltage interruptions Standard part File No. UL508C E179775 EMC characteristics may vary depending on the configuration of the users control panel, which contains the driver or stepping motor, or the arrangement and wiring of other electrical devices. Validation test of driver has been performed for low-voltage EMC directives at TUV (TUV SUD Japan) for self-declaration of CE marking. AC input Set model Micro step DC input Set model Micro step DC input Set model Full / half step Stepping Motor Linear Actuator Stepping Motor Stepping motor for vacuum environment Dimensions 29
Page 1 and 2: 5-PHASE STEPPING SYSTEMS Ver.5
Page 3 and 4: Index Features P. 4 Line Up P. 5 Li
Page 5 and 6: Line up Motor/driver sets are conve
Page 7 and 8: Stepping MotorP.84 - Connection Met
Page 9 and 10: Model number convention Example: Th
Page 11 and 12: Connector Set - Housing/Contact Lis
Page 13 and 14: Motor size 60mm sq. (2.36inch sq.)
Page 15 and 16: CE / UL model AC input DriverModel
Page 17 and 18: Motor size 86mm ( 3.39inch) 106m
Page 21 and 22: Motor size Motor + gear length 127.
Page 23 and 24: Harmonic gear model AC input Driver
Page 25 and 26: Electromagnetic brake model AC inpu
Page 27: Motor size Motor + brake length 180
Page 31 and 32: Connections and Signals External w
Page 33 and 34: Input circuit configuration of PD,
Page 37 and 38: Cables with connectorsIncluded in a
Page 41 and 42: Low-backlash gear model DC input Dr
Page 43 and 44: 60mm sq. (2.36inch sq.) Motor size
Page 47 and 48: 28mm sq. (1.10inch sq.) Motor size
Page 51 and 52: Electromagnetic brake model DC inpu
Page 53 and 54: Motor specifications General speci
Page 55 and 56: Driver Controls and Connectors 2 Fu
Page 57 and 58: Input circuit configuration of CW (
Page 59 and 60: Dimensions Stepping motor for vacuu
Page 63 and 64: Standard model DC input DriverModel
Page 65 and 66: Motor size 86mm ( 3.39inch) Motor
Page 71 and 72: Spur gear model DC input DriverMode
Page 73 and 74: Harmonic gear model DC input Driver
Page 79 and 80:
Driver specifications General spec
Page 81 and 82:
Connections and Signals External w
Page 83 and 84:
Input circuit configuration of PD
Page 85 and 86:
60mm ( 2.36inch) AC input Set mode
Page 87 and 88:
42mm sq. (1.65inch sq.) 0.72/step M
Page 89 and 90:
60mm sq. (2.36inch sq.) 0.72/step M
Page 91 and 92:
86mm ( 3.39inch) 0.72/step Motor w
Page 93 and 94:
Allowable radial / thrust load Radi
Page 95 and 96:
Linear Actuator Stepping Motor Line
Page 97 and 98:
Dimensions Stepping motor dimension
Page 99 and 100:
Set model configuration motor (stan
Page 101 and 102:
Set model configuration motor (Low-
Page 103 and 104:
Set model configuration motor (Harm
Page 105 and 106:
Stepping motor dimensions[Unit : mm
Page 107 and 108:
Safety Consideration The drivers an
Page 109 and 110:
Inquiry Check Sheet For more inform
Page 111 and 112:
MEMO
show all

5-PHASE STEPPING SYSTEMS - sanyo denki europe

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?