common - Sanyo Denki America, Inc.

More documents

Recommendations

Info

Safety Precautions <strong>common</strong> Prohibited Storage 1. Do not store the device where it could be exposed to rain, water, toxic gases or other liquids. Damage to the device could otherwise result. Operation 2. The built-in brake is intended to secure the motor; do not use it for regular control. Damage to the brake could otherwise result. Maintenance 3. Do not disassembly or repair the system. Doing so may result in fire or electric shock. General 4. Do not remove the nameplate cover attached to the device. Storage Mandatory 1. Store the system in a place which is not exposed to direct sunlight and in the determined temperature/humidity range (−20°C to +65°C, 90% RH or less without condensation). 2. When the system is to be stored for a long time (more than 3 years as a reference period), consult us. The capacity of the electrolytic capacitors decreases during long-term storage, and could cause damage to the device. Operation 3. Install an external emergency stop circuit that can stop the device and cut off the power instantaneously. Install an external protective circuit to the amplifier to cut off the power from the main circuit in the case of an alarm. Motor interruption, injury, burnout, fire and secondary damage could otherwise result. 4. Operate within the specified temperature and humidity range {Amplifier: Temperature 0 to 55, Humidity below 90% RH (non-condensing); Motor: Temperature 0 to 40Humidity below 90% RHnon-condensing) Transportation 5. Follow the directions written on the outside box. Excess stacking could result in collapse. 16
2. Model Number Specifications (<strong>common</strong>) 2. 1 Verifying Package Contents Verify the following items when the product arrives. If any discrepancies are noticed, contact our office. Verify that the model number is the same as ordered (model number is located on the main name plate). Verify that there are no defects, such as damage to the exterior of the device. 2.2 Model number Specifications 2.2.1 Set Number Specification The PB system has a set number based on the combination of amplifier and motor. Motor Option With holding brake No symbolwithout holding brake Motor Option Gear Ratiofor geared models No symbolNo gear Motor Option Gear (for geared models No symbolNo gear Motor Length Motor mounting surface edge dimension (mm) Amplifier I/F SpecificationMulti interface Power SpecificationDC input (24 / 48V System Series NamePB System 2.2.2 Set Product Packing List Product Quality Model Number Drawing Reference (page number) Amplifier (Note) 1 PB3D003M200 6-3 Motor 1 PBMF20 6-4 Power cable 1 PBC6P0010A1m 7-2 I/O cable (with shield) 1 PBC5S0010C1m 7-2 Note) Set product amplifier has the combination motor model number set in advance. To change the combination motor, transmitting is necessary to reset the new motor model number. As the need to reset will arise, please purchase the communication unit (refer to chapter 7: Options). For the set up method details, please refer to PC I/F Specifications M0007856 and Trial Operation (Sections 4.6 and 5.7) 21
Page 1 and 2: M0007846 SANMOTION CLOSED LOOP STEP
Page 3 and 4: Contents 1. Safety Pre
Page 5 and 6: Safety Precautions common 1.1 Int
Page 7 and 8: Safety Precautions common 1.3 Safet
Page 9: Safety Precautions common Operati
Page 13 and 14: 2. Model Number Specifications (com
Page 15 and 16: D5 6 7 8 9 A B C 3. Installation /
Page 17 and 18: 3. Installation / Wiring (common)
Page 23 and 24: Pulse Train Input Interface
Page 33 and 34: 4. Pulse Train Input Interface
Page 61 and 62:
Pulse Train Input Interface
Page 63 and 64:
Pulse Train Input Interface
Page 65 and 66:
5. Type R Interface
Page 67 and 68:
5. Type R Interface
Page 69 and 70:
5. Type R Interface
Page 71 and 72:
5. Type R Interface
Page 73 and 74:
5. Type R Interface
Page 75 and 76:
5. Type R Interface
Page 77 and 78:
5. Type R Interface
Page 79 and 80:
5. Type R Interface
Page 81 and 82:
5. Type R Interface
Page 83 and 84:
5. Type R Interface
Page 85 and 86:
5. Type R Interface
Page 87 and 88:
5. Type R Interface
Page 89 and 90:
5. Type R Interface
Page 91 and 92:
5. Type R Interface
Page 93 and 94:
5. Type R Interface
Page 95 and 96:
5. Type R Interface
Page 97 and 98:
5. Type R Interface
Page 99 and 100:
5. Type R Interface
Page 101 and 102:
5. Type R Interface
Page 103 and 104:
5. Type R Interface
Page 105 and 106:
5. Type R Interface
Page 107 and 108:
5. Type R Interface
Page 109 and 110:
5. Type R Interface
Page 111 and 112:
5. Type R Interface
Page 113 and 114:
5. Type R Interface
Page 115 and 116:
5. Type R Interface
Page 117 and 118:
5. Type R Interface
Page 119 and 120:
5. Type R Interface
Page 121 and 122:
5. Type R Interface
Page 123 and 124:
5. Type R Interface
Page 125 and 126:
5. Type R interface
Page 127 and 128:
5. Type R interface
Page 129 and 130:
5. Type R Interface
Page 131 and 132:
5. Type R Interface
Page 133 and 134:
5. Type R Interface
Page 135 and 136:
5. Type R Interface 5.8 Comm
Page 137 and 138:
5. Type R Interface 2 Status
Page 139 and 140:
5. Type R Interface 2Communi
Page 141 and 142:
5. Type R Interface 5.8.7 Co
Page 143 and 144:
6Specifications (common)
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
6. Basic Specificationscommon
Page 151 and 152:
5 6 7 8 9 A BCD E F 0 1 2 3 4 6. Ba
Page 153 and 154:
6. Basic Specificationscommon
Page 155 and 156:
7. Options 7. O
Page 157 and 158:
7. Options 7.2.3
Page 159 and 160:
7. Options 7.3 O
Page 161 and 162:
8. International Standards Conformi
show all

common - Sanyo Denki America, Inc.

Create successful ePaper yourself

Delete template?

Save as template?