AGFA d-lab.3 Digital Compact Lab
AGFA d-lab.3 Digital Compact Lab AGFA d-lab.3 Digital Compact Lab
Repair Printer Functional Check after the Replacement of Parts If parts are replaced on an assembly group which also influence the paper transport, a functional test with paper should be performed in the Service program. For this, the assembly group has to be pulled out and operated via the service cables. There are other Scripts available, besides the indicated ones: Scripts/scripts_printer/data_ld/allgemein/4x6slow.txt Scripts/scripts_printer/data_ld/allgemein/dplfast.txt Scripts/scripts_printer/data_ld/allgemein/ldls_prf.txt Scripts/scripts_printer/data_ld/allgemein/LD_vers.txt Scripts/scripts_printer/data_ld/allgemein/kontrollstreifen /cfast_go.txt Scripts/scripts_printer/data_ld/allgemein/kontrollstreifen /cslow_go.txt Scripts/scripts_printer/data_ld/motore/MO04kupl.txt Size 4x6 slow, without pressure, roller adjustment Size 4x6 with pressure by LD Light sensor test Version check LD and RSD Control strip test, quick Control strip test, slow Test magnetic clutch AGFA d-lab.3 2001-01-02 /PN 9009 6.4.61
Printer Repair Sheet Transfer ST, replacing Parts − Slacken 1 screw (1) − Pull ST to the front dlabr062 Replacing the Motor ST_MO01 Replacement required: Motor defective Allan key 1,5 Removal: − Dismount the hand wheel (1): 2 Allan screws on the shaft − Unscrew the metal bracket with handle (2) − Disconnect the connector (3) − Detach the motor from the clutch / the sync disk (4): 2 Allan screws − Slacken the belt by unscrewing the motor plate: 2 tensioning screw, 1 screw inside − Remove the motor plate − Unscrew the motor from the motor plate Installation: In reverse order − Tension the belt by shifting the motor plate − Install the assembly group and check the motor function in the Service program: Scripts/scripts_printer/data_ld/ST sheet Transfer dlabr293 6.4.62 2001-01-02 /PN 9009 AGFA d-lab.3
- Page 329 and 330: Printer Repair − Print a test pri
- Page 331 and 332: Printer Repair Hexagon socket screw
- Page 333 and 334: Printer Repair Replacing the Magazi
- Page 335 and 336: Printer Repair Replacing the Cutter
- Page 337 and 338: Printer Repair Replacing the Switch
- Page 339 and 340: Printer Repair Replacing the Motor
- Page 341 and 342: Printer Repair Replacing the Pressu
- Page 343 and 344: Printer Repair Sheet Bridge SB, rep
- Page 345 and 346: Printer Repair Replacing the Sync D
- Page 347 and 348: Printer Repair Transport Unit TU, r
- Page 349 and 350: Printer Repair Toothed Belt Adjust
- Page 351 and 352: Printer Repair Replacing the Turnta
- Page 353 and 354: Printer Repair Replacing the Motor
- Page 355 and 356: Printer Repair − Fastening of the
- Page 357 and 358: Printer Repair Replacing the Light
- Page 359 and 360: Printer Repair Replacing the Set of
- Page 361 and 362: Printer Repair Replacing the Set of
- Page 363 and 364: Printer Repair Replacing the comple
- Page 365 and 366: Printer Repair Replacing the Laser
- Page 367 and 368: Printer Repair Caution! Use only th
- Page 369 and 370: Printer Repair − The tip of the p
- Page 371 and 372: Printer Repair Replacing the AOM Am
- Page 373 and 374: Printer Repair Lane Distributor LD,
- Page 375 and 376: Printer Repair Replacing the LD_GS0
- Page 377 and 378: Printer Repair Replacing toothed Be
- Page 379: Printer Repair Readjust the print h
- Page 383 and 384: Printer Repair ■ 6.4.64 2001-01-0
- Page 385: Paper Processor Repair ■ 7.ii 200
- Page 389 and 390: Repair Paper Processor Block Circui
- Page 393 and 394: Repair Paper Processor Signal Lists
- Page 395 and 396: Repair Paper Processor Paper Exit P
- Page 397 and 398: Repair Paper Processor Connections
- Page 401 and 402: Repair Paper Processor Functional D
- Page 403 and 404: Repair Paper Processor Electrical S
- Page 405 and 406: Repair Paper Processor Paper Proces
- Page 407 and 408: Repair Paper Processor AC/DC Power
- Page 409 and 410: Repair Paper Processor AC Power Sup
- Page 411 and 412: Repair Paper Processor Densitometer
- Page 415 and 416: Repair Paper Processor Repair Repla
- Page 417 and 418: Repair Paper Processor Replacing Pr
- Page 419 and 420: Repair Paper Processor Temperature
- Page 421 and 422: Repair Software Contents Software S
- Page 425 and 426: Repair Software Software Structure
- Page 427 and 428: Repair Software Software Structure
- Page 429 and 430: Repair Maintenance Contents Mainten
Printer<br />
Repair<br />
Sheet Transfer ST, replacing Parts<br />
− Slacken 1 screw (1)<br />
− Pull ST to the front<br />
dlabr062<br />
Replacing the Motor ST_MO01<br />
Replacement required:<br />
Motor defective<br />
Allan key 1,5<br />
Removal:<br />
− Dismount the hand wheel (1):<br />
2 Allan screws on the shaft<br />
− Unscrew the metal bracket with handle (2)<br />
− Disconnect the connector (3)<br />
− Detach the motor from the clutch / the sync disk<br />
(4):<br />
2 Allan screws<br />
− Slacken the belt by unscrewing the motor plate:<br />
2 tensioning screw, 1 screw inside<br />
− Remove the motor plate<br />
− Unscrew the motor from the motor plate<br />
Installation:<br />
In reverse order<br />
− Tension the belt by shifting the motor plate<br />
− Install the assembly group and check the motor<br />
function in the Service program:<br />
Scripts/scripts_printer/data_ld/ST sheet<br />
Transfer<br />
dlabr293<br />
6.4.62 2001-01-02 /PN 9009 <strong>AGFA</strong> d-<strong>lab.3</strong>