AGFA d-lab.3 Digital Compact Lab
AGFA d-lab.3 Digital Compact Lab AGFA d-lab.3 Digital Compact Lab
Repair Printer Replacing the Pressure Rollers Screwdriver Removal: − Open the circlips and remove the assembly group Installation: − Observe the exact position of the torsion spring when installing the assembly group! − If necessary, compare it with the mounting position in the transport unit (TU). 1 Spring under the shaft 2 Shaft plugged through the spring turns 3 Spring rests on the shaft (behind circlip) dlabr209 Replacing the Sheet Turnaround Removal: − Hold the sheet turnaround on both rods (1) and pull it out − Remove the printed circuit: It is attached to the pins in the sheet bridge. dlaba111 Installation: − When mounting the sheet turnaround, push the belt back into the reference position dlaba112 AGFA d-lab.3 2001-01-02 /PN 9009 6.4.27
Printer Repair Transport Unit TU, replacing Parts − Open the locking (1) of the TU (red fastening screw) − Pull out the TU towards you − The transport unit has to be removed for some repair jobs: Remove 2 screws each (1) from the two telescopic rails dlaba009 dlabr110 6.4.28 2001-01-02 /PN 9009 AGFA d-lab.3
- Page 295 and 296: Printer Repair Circuit Diagram dlab
- Page 297 and 298: Printer Repair Laser Remote After t
- Page 299 and 300: Printer Repair Test Points MP1 +5 +
- Page 301 and 302: Printer Repair LA_GS05 - Red Laser
- Page 303 and 304: Printer Repair Lane Distributor LD
- Page 305 and 306: Printer Repair LD_GS01 - Lane Distr
- Page 307 and 308: Printer Repair RD_GS01 - Back Print
- Page 309 and 310: Printer Repair Laser Module (LA) Th
- Page 311 and 312: Printer Repair Laser Sources Laser
- Page 313 and 314: Printer Repair There are 2 methods
- Page 315 and 316: Printer Repair − Enter new values
- Page 317: Printer Repair − Define the pixel
- Page 321 and 322: Printer Repair Mainboard Replacemen
- Page 323 and 324: Printer Repair − Determine the op
- Page 325 and 326: Printer Repair Download XILINKS (pr
- Page 327 and 328: Printer Repair Loading setup values
- Page 329 and 330: Printer Repair − Print a test pri
- Page 331 and 332: Printer Repair Hexagon socket screw
- Page 333 and 334: Printer Repair Replacing the Magazi
- Page 335 and 336: Printer Repair Replacing the Cutter
- Page 337 and 338: Printer Repair Replacing the Switch
- Page 339 and 340: Printer Repair Replacing the Motor
- Page 341 and 342: Printer Repair Replacing the Pressu
- Page 343 and 344: Printer Repair Sheet Bridge SB, rep
- Page 345: Printer Repair Replacing the Sync D
- Page 349 and 350: Printer Repair Toothed Belt Adjust
- Page 351 and 352: Printer Repair Replacing the Turnta
- Page 353 and 354: Printer Repair Replacing the Motor
- Page 355 and 356: Printer Repair − Fastening of the
- Page 357 and 358: Printer Repair Replacing the Light
- Page 359 and 360: Printer Repair Replacing the Set of
- Page 361 and 362: Printer Repair Replacing the Set of
- Page 363 and 364: Printer Repair Replacing the comple
- Page 365 and 366: Printer Repair Replacing the Laser
- Page 367 and 368: Printer Repair Caution! Use only th
- Page 369 and 370: Printer Repair − The tip of the p
- Page 371 and 372: Printer Repair Replacing the AOM Am
- Page 373 and 374: Printer Repair Lane Distributor LD,
- Page 375 and 376: Printer Repair Replacing the LD_GS0
- Page 377 and 378: Printer Repair Replacing toothed Be
- Page 379 and 380: Printer Repair Readjust the print h
- Page 381 and 382: Printer Repair Sheet Transfer ST, r
- Page 383 and 384: Printer Repair ■ 6.4.64 2001-01-0
- Page 385: Paper Processor Repair ■ 7.ii 200
- Page 389 and 390: Repair Paper Processor Block Circui
- Page 393 and 394: Repair Paper Processor Signal Lists
- Page 395 and 396: Repair Paper Processor Paper Exit P
Repair<br />
Printer<br />
Replacing the Pressure Rollers<br />
Screwdriver<br />
Removal:<br />
− Open the circlips and remove the assembly group<br />
Installation:<br />
− Observe the exact position of the torsion spring<br />
when installing the assembly group!<br />
− If necessary, compare it with the mounting<br />
position in the transport unit (TU).<br />
1 Spring under the shaft<br />
2 Shaft plugged through the spring turns<br />
3 Spring rests on the shaft (behind circlip)<br />
dlabr209<br />
Replacing the Sheet Turnaround<br />
Removal:<br />
− Hold the sheet turnaround on both rods (1) and<br />
pull it out<br />
− Remove the printed circuit:<br />
It is attached to the pins in the sheet bridge.<br />
dlaba111<br />
Installation:<br />
− When mounting the sheet turnaround, push the<br />
belt back into the reference position<br />
dlaba112<br />
<strong>AGFA</strong> d-<strong>lab.3</strong> 2001-01-02 /PN 9009 6.4.27