AGFA d-lab.3 Digital Compact Lab
AGFA d-lab.3 Digital Compact Lab AGFA d-lab.3 Digital Compact Lab
Repair Printer Replacing the Sync Disks 7.8060.TUBH. / outer Toothed Belt 7.0389.6121. Dynamometer Seeger circlip ring pliers 3 – 10 mm ∅ − Remove the Seeger circlip ring − Replace the sync disks (1) and (3): The collar of the sync disks must be alternately on the belts. Risk of confusion! − Adjust the belt tension (2) by shifting the tensioning plate: The screw heads (4) to fasten the tensioning plate must not be on the belt side! dlabr207 Measure the belt tension in position (2): 1 Sync disk, flange out 2 Test point of the belt tension 3 Sync disk, flange in 4 Screw head not on the belt side − Deflection of the toothed belt: 1,7 mm − Test load: 1,0 N AGFA d-lab.3 2001-01-02 /PN 9009 6.4.25
Printer Repair Replacing the Sync Disks 7.8060.TUBH. / inside Toothed Belt 7.0389.6119. Allan key 3,0 Dynamometer Seeger circlip ring pliers 3 – 10 mm ∅ − Remove the Seeger circlip ring − Replace the sync disks (1) and (2): The collar of the sync disks must be alternately on the belts. Risk of confusion! − Adjust the belt tension (3) by shifting the tensioning plate: The screw heads to fasten the tensioning plate must not be on the belt side! dlabr208 Measure the belt tension in position (3): 1 Sync disk, flange out 2 Sync disk, flange in 3 Test point of the belt tension 4 Seeger circlip ring − Deflection of the toothed belt: 1,2 mm − Test load: 1,0 N Replacing the Transport Rollers Allan key 3,0 Seeger circlip ring pliers Dynamometer − Remove the sync disk − Remove the circlip from the ball bearing − Remove the transport shaft and pull out the transport roller If necessary, replace also the freewheel and the ball bearings when replacing the transport roller. Measure the belt tension in the indicated position (longest side): − Deflection of the toothed belt: 1,2 mm − Test load: 1,0 N 6.4.26 2001-01-02 /PN 9009 AGFA d-lab.3
- Page 293 and 294: Printer Repair PE_GS01, Layout dlab
- Page 295 and 296: Printer Repair Circuit Diagram dlab
- Page 297 and 298: Printer Repair Laser Remote After t
- Page 299 and 300: Printer Repair Test Points MP1 +5 +
- Page 301 and 302: Printer Repair LA_GS05 - Red Laser
- Page 303 and 304: Printer Repair Lane Distributor LD
- Page 305 and 306: Printer Repair LD_GS01 - Lane Distr
- Page 307 and 308: Printer Repair RD_GS01 - Back Print
- Page 309 and 310: Printer Repair Laser Module (LA) Th
- Page 311 and 312: Printer Repair Laser Sources Laser
- Page 313 and 314: Printer Repair There are 2 methods
- Page 315 and 316: Printer Repair − Enter new values
- Page 317: Printer Repair − Define the pixel
- Page 321 and 322: Printer Repair Mainboard Replacemen
- Page 323 and 324: Printer Repair − Determine the op
- Page 325 and 326: Printer Repair Download XILINKS (pr
- Page 327 and 328: Printer Repair Loading setup values
- Page 329 and 330: Printer Repair − Print a test pri
- Page 331 and 332: Printer Repair Hexagon socket screw
- Page 333 and 334: Printer Repair Replacing the Magazi
- Page 335 and 336: Printer Repair Replacing the Cutter
- Page 337 and 338: Printer Repair Replacing the Switch
- Page 339 and 340: Printer Repair Replacing the Motor
- Page 341 and 342: Printer Repair Replacing the Pressu
- Page 343: Printer Repair Sheet Bridge SB, rep
- Page 347 and 348: Printer Repair Transport Unit TU, r
- Page 349 and 350: Printer Repair Toothed Belt Adjust
- Page 351 and 352: Printer Repair Replacing the Turnta
- Page 353 and 354: Printer Repair Replacing the Motor
- Page 355 and 356: Printer Repair − Fastening of the
- Page 357 and 358: Printer Repair Replacing the Light
- Page 359 and 360: Printer Repair Replacing the Set of
- Page 361 and 362: Printer Repair Replacing the Set of
- Page 363 and 364: Printer Repair Replacing the comple
- Page 365 and 366: Printer Repair Replacing the Laser
- Page 367 and 368: Printer Repair Caution! Use only th
- Page 369 and 370: Printer Repair − The tip of the p
- Page 371 and 372: Printer Repair Replacing the AOM Am
- Page 373 and 374: Printer Repair Lane Distributor LD,
- Page 375 and 376: Printer Repair Replacing the LD_GS0
- Page 377 and 378: Printer Repair Replacing toothed Be
- Page 379 and 380: Printer Repair Readjust the print h
- Page 381 and 382: Printer Repair Sheet Transfer ST, r
- Page 383 and 384: Printer Repair ■ 6.4.64 2001-01-0
- Page 385: Paper Processor Repair ■ 7.ii 200
- Page 389 and 390: Repair Paper Processor Block Circui
- Page 393 and 394: Repair Paper Processor Signal Lists
Printer<br />
Repair<br />
Replacing the Sync Disks 7.8060.TUBH. / inside Toothed Belt 7.0389.6119.<br />
Allan key 3,0<br />
Dynamometer<br />
Seeger circlip ring pliers 3 – 10 mm ∅<br />
− Remove the Seeger circlip ring<br />
− Replace the sync disks (1) and (2):<br />
The collar of the sync disks must be alternately<br />
on the belts. Risk of confusion!<br />
− Adjust the belt tension (3) by shifting the<br />
tensioning plate:<br />
The screw heads to fasten the tensioning plate<br />
must not be on the belt side!<br />
dlabr208<br />
Measure the belt tension in position (3):<br />
1 Sync disk, flange out<br />
2 Sync disk, flange in<br />
3 Test point of the belt tension<br />
4 Seeger circlip ring<br />
− Deflection of the toothed belt: 1,2 mm<br />
− Test load: 1,0 N<br />
Replacing the Transport Rollers<br />
Allan key 3,0<br />
Seeger circlip ring pliers<br />
Dynamometer<br />
− Remove the sync disk<br />
− Remove the circlip from the ball bearing<br />
− Remove the transport shaft and pull out the<br />
transport roller<br />
If necessary, replace also the freewheel and the ball<br />
bearings when replacing the transport roller.<br />
Measure the belt tension in the indicated position<br />
(longest side):<br />
− Deflection of the toothed belt: 1,2 mm<br />
− Test load: 1,0 N<br />
6.4.26 2001-01-02 /PN 9009 <strong>AGFA</strong> d-<strong>lab.3</strong>