AGFA d-lab.3 Digital Compact Lab
AGFA d-lab.3 Digital Compact Lab AGFA d-lab.3 Digital Compact Lab
Repair Printer Replacing the Printer Power Supply Unit Replacement required: − Power supply unit defective − Fuse defective If the fuse is defective, replace the complete power supply unit. dlabr103 The manufacturer warrants only full functionality on condition that the power supply unit has been revised in the manufacturer’s plant. 1 Label (see Fig. below) 2 PO_GS01 Sticker dlabr104 AGFA d-lab.3 2001-01-02 /PN 9009 6.4.11
Printer Repair Hexagon socket screwdriver 4,0 Open the bottom side cover: − Open the LH paper magazine door − Push the button (1) to open the side cover − Remove the power supply unit: 4 screws (1) dlabr029 dlabr215 6.4.12 2001-01-02 /PN 9009 AGFA d-lab.3
- Page 279 and 280: Printer Repair − The paper transp
- Page 281 and 282: Printer Repair ML_GS02 / MR_GS02 an
- Page 283 and 284: Printer Repair Layout dlabr205 Volt
- Page 285 and 286: Printer Repair Transport Unit TU Fu
- Page 287 and 288: Printer Repair Voltages + 5V Logic
- Page 289 and 290: Printer Repair Laser Module Warning
- Page 291 and 292: Printer Repair Connection of the po
- Page 293 and 294: Printer Repair PE_GS01, Layout dlab
- Page 295 and 296: Printer Repair Circuit Diagram dlab
- Page 297 and 298: Printer Repair Laser Remote After t
- Page 299 and 300: Printer Repair Test Points MP1 +5 +
- Page 301 and 302: Printer Repair LA_GS05 - Red Laser
- Page 303 and 304: Printer Repair Lane Distributor LD
- Page 305 and 306: Printer Repair LD_GS01 - Lane Distr
- Page 307 and 308: Printer Repair RD_GS01 - Back Print
- Page 309 and 310: Printer Repair Laser Module (LA) Th
- Page 311 and 312: Printer Repair Laser Sources Laser
- Page 313 and 314: Printer Repair There are 2 methods
- Page 315 and 316: Printer Repair − Enter new values
- Page 317: Printer Repair − Define the pixel
- Page 321 and 322: Printer Repair Mainboard Replacemen
- Page 323 and 324: Printer Repair − Determine the op
- Page 325 and 326: Printer Repair Download XILINKS (pr
- Page 327 and 328: Printer Repair Loading setup values
- Page 329: Printer Repair − Print a test pri
- Page 333 and 334: Printer Repair Replacing the Magazi
- Page 335 and 336: Printer Repair Replacing the Cutter
- Page 337 and 338: Printer Repair Replacing the Switch
- Page 339 and 340: Printer Repair Replacing the Motor
- Page 341 and 342: Printer Repair Replacing the Pressu
- Page 343 and 344: Printer Repair Sheet Bridge SB, rep
- Page 345 and 346: Printer Repair Replacing the Sync D
- Page 347 and 348: Printer Repair Transport Unit TU, r
- Page 349 and 350: Printer Repair Toothed Belt Adjust
- Page 351 and 352: Printer Repair Replacing the Turnta
- Page 353 and 354: Printer Repair Replacing the Motor
- Page 355 and 356: Printer Repair − Fastening of the
- Page 357 and 358: Printer Repair Replacing the Light
- Page 359 and 360: Printer Repair Replacing the Set of
- Page 361 and 362: Printer Repair Replacing the Set of
- Page 363 and 364: Printer Repair Replacing the comple
- Page 365 and 366: Printer Repair Replacing the Laser
- Page 367 and 368: Printer Repair Caution! Use only th
- Page 369 and 370: Printer Repair − The tip of the p
- Page 371 and 372: Printer Repair Replacing the AOM Am
- Page 373 and 374: Printer Repair Lane Distributor LD,
- Page 375 and 376: Printer Repair Replacing the LD_GS0
- Page 377 and 378: Printer Repair Replacing toothed Be
- Page 379 and 380: Printer Repair Readjust the print h
Repair<br />
Printer<br />
Replacing the Printer Power Supply Unit<br />
Replacement required:<br />
− Power supply unit defective<br />
− Fuse defective<br />
If the fuse is defective, replace the complete<br />
power supply unit.<br />
dlabr103<br />
The manufacturer warrants only full functionality on<br />
condition that the power supply unit has been<br />
revised in the manufacturer’s plant.<br />
1 <strong>Lab</strong>el (see Fig. below)<br />
2 PO_GS01<br />
Sticker<br />
dlabr104<br />
<strong>AGFA</strong> d-<strong>lab.3</strong> 2001-01-02 /PN 9009 6.4.11