AGFA d-lab.3 Digital Compact Lab
AGFA d-lab.3 Digital Compact Lab AGFA d-lab.3 Digital Compact Lab
Repair Printer Adjustment of the video voltages: − Adjustment of the video voltages must be made prior to the determination of AOM characteristic curves. − Execute script Scripts/scripts for service/ printer/laser/register_mode_on.txt (Answer the prompt – Switch OFF dynamic noise reduction of laser? – with YES) − Accept the suggested values (0,0,0,0,100,5000) − Connect the Multimeter at the respective point and the plug housing (GND) (Illustration lower circles) − Adjust the video voltages with the respective controls (Illustration upper circles) − Adjust the following values: red 390mV +/- 30mV green, blue 365mV +/- 30mV − Execute the script Scripts/scripts for service/ printer/laser/register_mode_on.txt. (Answer the prompt – Switch OFF dynamic noise reduction of laser? – with YES) Final check and tests Checking the software versions: − Check the firmware version in the Service GUI, compare as explained in the procedure above. Check the setup values: − Start the script Scripts/scripts for service/setup/ printer_setup_backup.txt. AGFA d-lab.3 2001-01-02 /PN 9009 6.4.9
Printer Repair − Print a test print. To do so execute Scripts/Scripts for service/ testprints/X-print.txt. Evaluate the parameter (BOL, pixel shift, center of laser line...) and correct if necessary. (In case of correction save the SETUP values again.) − Verify that jumper J5 of the Printer Mainboard is open (risk of light reflection). − For safety execute script scripts for service/initialisierung/ pr_board_selftest.txt again. − Run a communication test between the Printer Mainboard and the VIPS Board by executing the script: Script Files/scripts_Printer/ printer_general/test lvds short.txt Message at the end: Test ready /0 Error(s), LVDS-Interface o.K. − After end of this script the machine program must be started again with the ON button. − Statistics values laser: After replacement of the Printer Mainboard the runtime statistics of the laser must be started again. To do so execute the script: Scripts for service\printer\laser statistic_laser.txt Answer the questions with YES so the values for the gas laser are reset to zero. Counting of the number of ignitions and operating hours starts again. 6.4.10 2001-01-02 /PN 9009 AGFA d-lab.3
- Page 277 and 278: Printer Repair Magazine Drive MD ML
- Page 279 and 280: Printer Repair − The paper transp
- Page 281 and 282: Printer Repair ML_GS02 / MR_GS02 an
- Page 283 and 284: Printer Repair Layout dlabr205 Volt
- Page 285 and 286: Printer Repair Transport Unit TU Fu
- Page 287 and 288: Printer Repair Voltages + 5V Logic
- Page 289 and 290: Printer Repair Laser Module Warning
- Page 291 and 292: Printer Repair Connection of the po
- Page 293 and 294: Printer Repair PE_GS01, Layout dlab
- Page 295 and 296: Printer Repair Circuit Diagram dlab
- Page 297 and 298: Printer Repair Laser Remote After t
- Page 299 and 300: Printer Repair Test Points MP1 +5 +
- Page 301 and 302: Printer Repair LA_GS05 - Red Laser
- Page 303 and 304: Printer Repair Lane Distributor LD
- Page 305 and 306: Printer Repair LD_GS01 - Lane Distr
- Page 307 and 308: Printer Repair RD_GS01 - Back Print
- Page 309 and 310: Printer Repair Laser Module (LA) Th
- Page 311 and 312: Printer Repair Laser Sources Laser
- Page 313 and 314: Printer Repair There are 2 methods
- Page 315 and 316: Printer Repair − Enter new values
- Page 317: Printer Repair − Define the pixel
- Page 321 and 322: Printer Repair Mainboard Replacemen
- Page 323 and 324: Printer Repair − Determine the op
- Page 325 and 326: Printer Repair Download XILINKS (pr
- Page 327: Printer Repair Loading setup values
- Page 331 and 332: Printer Repair Hexagon socket screw
- Page 333 and 334: Printer Repair Replacing the Magazi
- Page 335 and 336: Printer Repair Replacing the Cutter
- Page 337 and 338: Printer Repair Replacing the Switch
- Page 339 and 340: Printer Repair Replacing the Motor
- Page 341 and 342: Printer Repair Replacing the Pressu
- Page 343 and 344: Printer Repair Sheet Bridge SB, rep
- Page 345 and 346: Printer Repair Replacing the Sync D
- Page 347 and 348: Printer Repair Transport Unit TU, r
- Page 349 and 350: Printer Repair Toothed Belt Adjust
- Page 351 and 352: Printer Repair Replacing the Turnta
- Page 353 and 354: Printer Repair Replacing the Motor
- Page 355 and 356: Printer Repair − Fastening of the
- Page 357 and 358: Printer Repair Replacing the Light
- Page 359 and 360: Printer Repair Replacing the Set of
- Page 361 and 362: Printer Repair Replacing the Set of
- Page 363 and 364: Printer Repair Replacing the comple
- Page 365 and 366: Printer Repair Replacing the Laser
- Page 367 and 368: Printer Repair Caution! Use only th
- Page 369 and 370: Printer Repair − The tip of the p
- Page 371 and 372: Printer Repair Replacing the AOM Am
- Page 373 and 374: Printer Repair Lane Distributor LD,
- Page 375 and 376: Printer Repair Replacing the LD_GS0
- Page 377 and 378: Printer Repair Replacing toothed Be
Printer<br />
Repair<br />
− Print a test print.<br />
To do so execute Scripts/Scripts for<br />
service/<br />
testprints/X-print.txt.<br />
Evaluate the parameter (BOL, pixel shift, center<br />
of laser line...) and correct if necessary. (In case<br />
of correction save the SETUP values again.)<br />
− Verify that jumper J5 of the Printer Mainboard is<br />
open (risk of light reflection).<br />
− For safety execute script scripts for<br />
service/initialisierung/<br />
pr_board_selftest.txt again.<br />
− Run a communication test between the Printer<br />
Mainboard and the VIPS Board by executing the<br />
script:<br />
Script Files/scripts_Printer/<br />
printer_general/test lvds short.txt<br />
Message at the end:<br />
Test ready /0 Error(s), LVDS-Interface o.K.<br />
− After end of this script the machine program must<br />
be started again with the ON button.<br />
− Statistics values laser:<br />
After replacement of the Printer Mainboard the<br />
runtime statistics of the laser must be started<br />
again. To do so execute the script:<br />
Scripts for service\printer\laser<br />
statistic_laser.txt<br />
Answer the questions with YES so the values for<br />
the gas laser are reset to zero. Counting of the<br />
number of ignitions and operating hours starts<br />
again.<br />
6.4.10 2001-01-02 /PN 9009 <strong>AGFA</strong> d-<strong>lab.3</strong>