AGFA d-lab.3 Digital Compact Lab
AGFA d-lab.3 Digital Compact Lab AGFA d-lab.3 Digital Compact Lab
Repair Printer Layout dlabr203 Voltages + 5V Logic supply + 6,5V Logic source voltage + 24V Supply voltage (required for the output stage of the magnetic coupling) + 36V Power voltage supply Jumpers J1 Not plugged in Only for Service: Activation of the display LEDs, operating conditions can be checked plugged in J3 Not plugged in (no function) LED Display D2 LED red Lights when the SPI Controller is Reset D54 LED green Lights when +5V supply voltage is applied Test Points MP1 GND MP2 PGND GND against 5V derived from the +36V supply voltage AGFA d-lab.3 2001-01-02 /PN 9009 6.3.55
Printer Repair RD_GS01 - Back Printer Control Position Lane Distributor, bottom dlabr119 6.3.56 2001-01-02 /PN 9009 AGFA d-lab.3
- Page 255 and 256: Printer Repair Behaviour upon Print
- Page 257 and 258: Printer Repair Sheet Rotation / She
- Page 259 and 260: Printer Repair Roller Exit, Part 1
- Page 261 and 262: Printer Repair Flowcharts, Lane Dis
- Page 263 and 264: Printer Repair Sheet Distribution -
- Page 265 and 266: Printer Repair Sheet Transfer to Pa
- Page 267 and 268: Printer Repair Functional Descripti
- Page 269 and 270: Printer Repair 4. Begin Off Line (B
- Page 271 and 272: Printer Repair The following modes
- Page 273 and 274: Printer Repair 17. Calculation The
- Page 275 and 276: Printer Repair PF_GS01 - Technical
- Page 277 and 278: Printer Repair Magazine Drive MD ML
- Page 279 and 280: Printer Repair − The paper transp
- Page 281 and 282: Printer Repair ML_GS02 / MR_GS02 an
- Page 283 and 284: Printer Repair Layout dlabr205 Volt
- Page 285 and 286: Printer Repair Transport Unit TU Fu
- Page 287 and 288: Printer Repair Voltages + 5V Logic
- Page 289 and 290: Printer Repair Laser Module Warning
- Page 291 and 292: Printer Repair Connection of the po
- Page 293 and 294: Printer Repair PE_GS01, Layout dlab
- Page 295 and 296: Printer Repair Circuit Diagram dlab
- Page 297 and 298: Printer Repair Laser Remote After t
- Page 299 and 300: Printer Repair Test Points MP1 +5 +
- Page 301 and 302: Printer Repair LA_GS05 - Red Laser
- Page 303 and 304: Printer Repair Lane Distributor LD
- Page 305: Printer Repair LD_GS01 - Lane Distr
- Page 309 and 310: Printer Repair Laser Module (LA) Th
- Page 311 and 312: Printer Repair Laser Sources Laser
- Page 313 and 314: Printer Repair There are 2 methods
- Page 315 and 316: Printer Repair − Enter new values
- Page 317: Printer Repair − Define the pixel
- Page 321 and 322: Printer Repair Mainboard Replacemen
- Page 323 and 324: Printer Repair − Determine the op
- Page 325 and 326: Printer Repair Download XILINKS (pr
- Page 327 and 328: Printer Repair Loading setup values
- Page 329 and 330: Printer Repair − Print a test pri
- Page 331 and 332: Printer Repair Hexagon socket screw
- Page 333 and 334: Printer Repair Replacing the Magazi
- Page 335 and 336: Printer Repair Replacing the Cutter
- Page 337 and 338: Printer Repair Replacing the Switch
- Page 339 and 340: Printer Repair Replacing the Motor
- Page 341 and 342: Printer Repair Replacing the Pressu
- Page 343 and 344: Printer Repair Sheet Bridge SB, rep
- Page 345 and 346: Printer Repair Replacing the Sync D
- Page 347 and 348: Printer Repair Transport Unit TU, r
- Page 349 and 350: Printer Repair Toothed Belt Adjust
- Page 351 and 352: Printer Repair Replacing the Turnta
- Page 353 and 354: Printer Repair Replacing the Motor
- Page 355 and 356: Printer Repair − Fastening of the
Repair<br />
Printer<br />
Layout<br />
dlabr203<br />
Voltages<br />
+ 5V Logic supply<br />
+ 6,5V Logic source voltage<br />
+ 24V Supply voltage (required for the output stage of the magnetic coupling)<br />
+ 36V Power voltage supply<br />
Jumpers<br />
J1<br />
Not plugged in<br />
Only for Service: Activation of the display LEDs, operating conditions can be checked<br />
plugged in<br />
J3 Not plugged in (no function)<br />
LED Display<br />
D2 LED red Lights when the SPI Controller is Reset<br />
D54 LED green Lights when +5V supply voltage is applied<br />
Test Points<br />
MP1<br />
GND<br />
MP2 PGND GND against 5V derived from the +36V supply voltage<br />
<strong>AGFA</strong> d-<strong>lab.3</strong> 2001-01-02 /PN 9009 6.3.55