AGFA d-lab.3 Digital Compact Lab
AGFA d-lab.3 Digital Compact Lab AGFA d-lab.3 Digital Compact Lab
Repair Printer LA_GS01 – Distributor Board Functional Description LA_GS01: L8.8060.2090. − Distributor board with voltage generation − Distributes the colour signals coming from the Printer control board PF_GS01. These signals are used to modulate the AOMs. dlabrf48 Layout dlabr169 AGFA d-lab.3 2001-01-02 /PN 9009 6.3.49
Printer Repair LA_GS05 – Red Laser Diode Functional Description − Generates the red laser beam − Ensures a constant temperature for the laser diode (temperature compensation generated on the board) dlabrg48 LA_GS07 - Polygonal Drive Functional Description LA_GS07 controls/monitors the polygonal rotation. The rotation speed must be constant so that the prints are exposed without distortion. dlabrc48 6.3.50 2001-01-02 /PN 9009 AGFA d-lab.3
- Page 249: Printer Repair ST29 Pin connector s
- Page 253 and 254: Printer Repair Paper Transport and
- Page 255 and 256: Printer Repair Behaviour upon Print
- Page 257 and 258: Printer Repair Sheet Rotation / She
- Page 259 and 260: Printer Repair Roller Exit, Part 1
- Page 261 and 262: Printer Repair Flowcharts, Lane Dis
- Page 263 and 264: Printer Repair Sheet Distribution -
- Page 265 and 266: Printer Repair Sheet Transfer to Pa
- Page 267 and 268: Printer Repair Functional Descripti
- Page 269 and 270: Printer Repair 4. Begin Off Line (B
- Page 271 and 272: Printer Repair The following modes
- Page 273 and 274: Printer Repair 17. Calculation The
- Page 275 and 276: Printer Repair PF_GS01 - Technical
- Page 277 and 278: Printer Repair Magazine Drive MD ML
- Page 279 and 280: Printer Repair − The paper transp
- Page 281 and 282: Printer Repair ML_GS02 / MR_GS02 an
- Page 283 and 284: Printer Repair Layout dlabr205 Volt
- Page 285 and 286: Printer Repair Transport Unit TU Fu
- Page 287 and 288: Printer Repair Voltages + 5V Logic
- Page 289 and 290: Printer Repair Laser Module Warning
- Page 291 and 292: Printer Repair Connection of the po
- Page 293 and 294: Printer Repair PE_GS01, Layout dlab
- Page 295 and 296: Printer Repair Circuit Diagram dlab
- Page 297 and 298: Printer Repair Laser Remote After t
- Page 299: Printer Repair Test Points MP1 +5 +
- Page 303 and 304: Printer Repair Lane Distributor LD
- Page 305 and 306: Printer Repair LD_GS01 - Lane Distr
- Page 307 and 308: Printer Repair RD_GS01 - Back Print
- Page 309 and 310: Printer Repair Laser Module (LA) Th
- Page 311 and 312: Printer Repair Laser Sources Laser
- Page 313 and 314: Printer Repair There are 2 methods
- Page 315 and 316: Printer Repair − Enter new values
- Page 317: Printer Repair − Define the pixel
- Page 321 and 322: Printer Repair Mainboard Replacemen
- Page 323 and 324: Printer Repair − Determine the op
- Page 325 and 326: Printer Repair Download XILINKS (pr
- Page 327 and 328: Printer Repair Loading setup values
- Page 329 and 330: Printer Repair − Print a test pri
- Page 331 and 332: Printer Repair Hexagon socket screw
- Page 333 and 334: Printer Repair Replacing the Magazi
- Page 335 and 336: Printer Repair Replacing the Cutter
- Page 337 and 338: Printer Repair Replacing the Switch
- Page 339 and 340: Printer Repair Replacing the Motor
- Page 341 and 342: Printer Repair Replacing the Pressu
- Page 343 and 344: Printer Repair Sheet Bridge SB, rep
- Page 345 and 346: Printer Repair Replacing the Sync D
- Page 347 and 348: Printer Repair Transport Unit TU, r
- Page 349 and 350: Printer Repair Toothed Belt Adjust
Printer<br />
Repair<br />
LA_GS05 – Red Laser Diode<br />
Functional Description<br />
− Generates the red laser beam<br />
− Ensures a constant temperature for the laser<br />
diode (temperature compensation generated on<br />
the board)<br />
dlabrg48<br />
LA_GS07 - Polygonal Drive<br />
Functional Description<br />
LA_GS07 controls/monitors the polygonal rotation.<br />
The rotation speed must be constant so that the<br />
prints are exposed without distortion.<br />
dlabrc48<br />
6.3.50 2001-01-02 /PN 9009 <strong>AGFA</strong> d-<strong>lab.3</strong>
Change language