AGFA d-lab.3 Digital Compact Lab
AGFA d-lab.3 Digital Compact Lab AGFA d-lab.3 Digital Compact Lab
Repair Printer TU_GS01 (Transport Unit Control) Functional Description Particularity: The primary logic and the power electronic are electrically separated. − Control of the TU assembly group − Communication with the Printer Mainboard PF_GS01 Position: Behind the front cover of the TU dlabr068 Layout dlabr206 AGFA d-lab.3 2001-01-02 /PN 9009 6.3.35
Printer Repair Voltages + 5V Logic supply + 36V Power voltage supply Jumper ST3 not plugged in Only for Service: plugged in Activation of the display LEDs, operating conditions can be checked LED Display D2 LED green Lights when logic voltage +5V is applied on the microcontroller (is in Hardware Reset) switching part D51 LED red Lights when logic voltage +5V is applied on the microcontroller (is in Hardware Reset) switching part Connectors ST1 ST5 ST24 ST27 assigned assigned assigned assigned 6.3.36 2001-01-02 /PN 9009 AGFA d-lab.3
- Page 235 and 236: Printer Repair ST 3: SPI - Interfac
- Page 237 and 238: Printer Repair ST 7: SPI - Interfac
- Page 239 and 240: Printer Repair ST 26: CAN - Interfa
- Page 241 and 242: Printer Repair Printer Mainboard, C
- Page 243 and 244: Printer Repair ST17 Trailing cable
- Page 245 and 246: Printer Repair PE_GS01, Connector A
- Page 247 and 248: Printer Repair ST11 DC motor supply
- Page 249: Printer Repair ST29 Pin connector s
- Page 253 and 254: Printer Repair Paper Transport and
- Page 255 and 256: Printer Repair Behaviour upon Print
- Page 257 and 258: Printer Repair Sheet Rotation / She
- Page 259 and 260: Printer Repair Roller Exit, Part 1
- Page 261 and 262: Printer Repair Flowcharts, Lane Dis
- Page 263 and 264: Printer Repair Sheet Distribution -
- Page 265 and 266: Printer Repair Sheet Transfer to Pa
- Page 267 and 268: Printer Repair Functional Descripti
- Page 269 and 270: Printer Repair 4. Begin Off Line (B
- Page 271 and 272: Printer Repair The following modes
- Page 273 and 274: Printer Repair 17. Calculation The
- Page 275 and 276: Printer Repair PF_GS01 - Technical
- Page 277 and 278: Printer Repair Magazine Drive MD ML
- Page 279 and 280: Printer Repair − The paper transp
- Page 281 and 282: Printer Repair ML_GS02 / MR_GS02 an
- Page 283 and 284: Printer Repair Layout dlabr205 Volt
- Page 285: Printer Repair Transport Unit TU Fu
- Page 289 and 290: Printer Repair Laser Module Warning
- Page 291 and 292: Printer Repair Connection of the po
- Page 293 and 294: Printer Repair PE_GS01, Layout dlab
- Page 295 and 296: Printer Repair Circuit Diagram dlab
- Page 297 and 298: Printer Repair Laser Remote After t
- Page 299 and 300: Printer Repair Test Points MP1 +5 +
- Page 301 and 302: Printer Repair LA_GS05 - Red Laser
- Page 303 and 304: Printer Repair Lane Distributor LD
- Page 305 and 306: Printer Repair LD_GS01 - Lane Distr
- Page 307 and 308: Printer Repair RD_GS01 - Back Print
- Page 309 and 310: Printer Repair Laser Module (LA) Th
- Page 311 and 312: Printer Repair Laser Sources Laser
- Page 313 and 314: Printer Repair There are 2 methods
- Page 315 and 316: Printer Repair − Enter new values
- Page 317: Printer Repair − Define the pixel
- Page 321 and 322: Printer Repair Mainboard Replacemen
- Page 323 and 324: Printer Repair − Determine the op
- Page 325 and 326: Printer Repair Download XILINKS (pr
- Page 327 and 328: Printer Repair Loading setup values
- Page 329 and 330: Printer Repair − Print a test pri
- Page 331 and 332: Printer Repair Hexagon socket screw
- Page 333 and 334: Printer Repair Replacing the Magazi
- Page 335 and 336: Printer Repair Replacing the Cutter
Repair<br />
Printer<br />
TU_GS01 (Transport Unit Control)<br />
Functional Description<br />
Particularity:<br />
The primary logic and the power electronic are<br />
electrically separated.<br />
− Control of the TU assembly group<br />
− Communication with the Printer Mainboard<br />
PF_GS01<br />
Position: Behind the front cover of the TU<br />
dlabr068<br />
Layout<br />
dlabr206<br />
<strong>AGFA</strong> d-<strong>lab.3</strong> 2001-01-02 /PN 9009 6.3.35