AGFA d-lab.3 Digital Compact Lab
AGFA d-lab.3 Digital Compact Lab AGFA d-lab.3 Digital Compact Lab
Repair Printer Switching Gear SG SG_GS01 – Switching Gear Control Functional Description SG = Switching Gear Magazine drive: SG_GS01 sends the sensor signal for the measuring length (PSG, NSG) that defines the distance between two sensors for which a step number is found. It is needed for the calculation of the winding core. Position SG_GS01 is located on the fan assembly group below the assembly group SG (1). 1 The electrical connection is interrupted when the fan assembly group is removed. dlabr146 AGFA d-lab.3 2001-01-02 /PN 9009 6.3.31
Printer Repair Layout dlabr205 Voltages + 5V Logic supply + 24V Supply voltage + 36V Power voltage supply Jumper J1 not plugged in Only for service: plugged in Activation of the display LEDs, operating conditions can be checked LED Display D1 LED red Lights when SPI Controller is Reset D12 LED green Lights when +5V supply voltage is applied 6.3.32 2001-01-02 /PN 9009 AGFA d-lab.3
- Page 231 and 232: Printer Repair Laser Module LA Some
- Page 233 and 234: Printer Repair Sheet Transfer ST Pr
- Page 235 and 236: Printer Repair ST 3: SPI - Interfac
- Page 237 and 238: Printer Repair ST 7: SPI - Interfac
- Page 239 and 240: Printer Repair ST 26: CAN - Interfa
- Page 241 and 242: Printer Repair Printer Mainboard, C
- Page 243 and 244: Printer Repair ST17 Trailing cable
- Page 245 and 246: Printer Repair PE_GS01, Connector A
- Page 247 and 248: Printer Repair ST11 DC motor supply
- Page 249: Printer Repair ST29 Pin connector s
- Page 253 and 254: Printer Repair Paper Transport and
- Page 255 and 256: Printer Repair Behaviour upon Print
- Page 257 and 258: Printer Repair Sheet Rotation / She
- Page 259 and 260: Printer Repair Roller Exit, Part 1
- Page 261 and 262: Printer Repair Flowcharts, Lane Dis
- Page 263 and 264: Printer Repair Sheet Distribution -
- Page 265 and 266: Printer Repair Sheet Transfer to Pa
- Page 267 and 268: Printer Repair Functional Descripti
- Page 269 and 270: Printer Repair 4. Begin Off Line (B
- Page 271 and 272: Printer Repair The following modes
- Page 273 and 274: Printer Repair 17. Calculation The
- Page 275 and 276: Printer Repair PF_GS01 - Technical
- Page 277 and 278: Printer Repair Magazine Drive MD ML
- Page 279 and 280: Printer Repair − The paper transp
- Page 281: Printer Repair ML_GS02 / MR_GS02 an
- Page 285 and 286: Printer Repair Transport Unit TU Fu
- Page 287 and 288: Printer Repair Voltages + 5V Logic
- Page 289 and 290: Printer Repair Laser Module Warning
- Page 291 and 292: Printer Repair Connection of the po
- Page 293 and 294: Printer Repair PE_GS01, Layout dlab
- Page 295 and 296: Printer Repair Circuit Diagram dlab
- Page 297 and 298: Printer Repair Laser Remote After t
- Page 299 and 300: Printer Repair Test Points MP1 +5 +
- Page 301 and 302: Printer Repair LA_GS05 - Red Laser
- Page 303 and 304: Printer Repair Lane Distributor LD
- Page 305 and 306: Printer Repair LD_GS01 - Lane Distr
- Page 307 and 308: Printer Repair RD_GS01 - Back Print
- Page 309 and 310: Printer Repair Laser Module (LA) Th
- Page 311 and 312: Printer Repair Laser Sources Laser
- Page 313 and 314: Printer Repair There are 2 methods
- Page 315 and 316: Printer Repair − Enter new values
- Page 317: Printer Repair − Define the pixel
- Page 321 and 322: Printer Repair Mainboard Replacemen
- Page 323 and 324: Printer Repair − Determine the op
- Page 325 and 326: Printer Repair Download XILINKS (pr
- Page 327 and 328: Printer Repair Loading setup values
- Page 329 and 330: Printer Repair − Print a test pri
- Page 331 and 332: Printer Repair Hexagon socket screw
Printer<br />
Repair<br />
Layout<br />
dlabr205<br />
Voltages<br />
+ 5V Logic supply<br />
+ 24V Supply voltage<br />
+ 36V Power voltage supply<br />
Jumper<br />
J1<br />
not plugged in<br />
Only for service:<br />
plugged in<br />
Activation of the display LEDs, operating conditions can be checked<br />
LED Display<br />
D1 LED red Lights when SPI Controller is Reset<br />
D12 LED green Lights when +5V supply voltage is applied<br />
6.3.32 2001-01-02 /PN 9009 <strong>AGFA</strong> d-<strong>lab.3</strong>