AGFA d-lab.3 Digital Compact Lab
AGFA d-lab.3 Digital Compact Lab AGFA d-lab.3 Digital Compact Lab
Repair Printer Jumpers J1 not plugged in J2 not plugged in J3 plugged in Main clock for data pipeline (60,929170 MHz) J4 not plugged in J5 not plugged in The Jumper must not remain plugged in during normal operation! Only for the LEDs active, the operating conditions can be checked service: plugged in J6 plugged in CAN-termination resistor active LED Display D1 LED red Lights when the Reset line on the SPI Interface is active D2 LED red Initialisation FPGA (signal/INITX in the SP) D3 LED red Polygon facet not synchronous D4 LED red Picture error D33 LED yellow End of line (EOL), during Lineretrace D34 LED yellow Picture work, lights during the image output D35 LED yellow no significance D36 LED yellow FIFO empty latch lights when a communication error occurs with the LVDS interface D37 LED yellow FIFO almost full D38 LED yellow FIFO full latch, communication error with the LVDS interface Test Points MP3 +5V MP4 GND GND against +5V MP7 +5V (digital) MP8 +3,3V(digital) MP9 Video output voltage Red channel MP10 Video analogue GND MP11 Video output voltage Blue channel MP12 Video output voltage Green channel MP13 Measuring voltage laser energy Green channel MP14 DC-compensated amplified noise voltage Green channel (0...1,2...2,4V) MP15 Measuring voltage laser voltage Blue channel MP16 DC-compensated amplified noise voltage Blue channel (0...1,2...2,4V) MP23 Not used ST33 Test point for EOL signal ST34 Test point for Picture Work Connector Allocation see Printer Mainboard in register 6.2 AGFA d-lab.3 2001-01-02 /PN 9009 6.3.25
Printer Repair Magazine Drive MD ML_GS01_GS – LH Magazine Drive MR_GS01_GS - RH Magazine Drive Functional Description MD = Magazine Drive ML_GS01_GS – Magazine Drive 8.8060.2150. MR_GS01_GS - Magazine Drive 8.8060.2150. Drive of the Paper magazines: − Paper Magazine (ML) − Paper Magazine (MR) The central control unit SPI (Serial Peripheral Interface) comprises the following functional assembly groups: − DC/DC converter to supply the +5 V operating voltage − Voltage monitoring of the +36 V and +24 V power voltages − RS232 interface to output the test displays of the AVR module with the following settings: − Transfer rate = 19,2 kBaud − Data bits = 8 − Stop bits = 1 − Parity = None − Protocol = Xon / Xoff − RESET generator to link the various RESET sources. − Clock generator 8 MHz − The SPI interface drivers with a transfer rate of 1Mbit/s. 6.3.26 2001-01-02 /PN 9009 AGFA d-lab.3
- Page 225 and 226: Printer Repair Printer Mainboard PF
- Page 227 and 228: Printer Repair Paper Magazine RH MR
- Page 229 and 230: Printer Repair Transport Unit TU /
- Page 231 and 232: Printer Repair Laser Module LA Some
- Page 233 and 234: Printer Repair Sheet Transfer ST Pr
- Page 235 and 236: Printer Repair ST 3: SPI - Interfac
- Page 237 and 238: Printer Repair ST 7: SPI - Interfac
- Page 239 and 240: Printer Repair ST 26: CAN - Interfa
- Page 241 and 242: Printer Repair Printer Mainboard, C
- Page 243 and 244: Printer Repair ST17 Trailing cable
- Page 245 and 246: Printer Repair PE_GS01, Connector A
- Page 247 and 248: Printer Repair ST11 DC motor supply
- Page 249: Printer Repair ST29 Pin connector s
- Page 253 and 254: Printer Repair Paper Transport and
- Page 255 and 256: Printer Repair Behaviour upon Print
- Page 257 and 258: Printer Repair Sheet Rotation / She
- Page 259 and 260: Printer Repair Roller Exit, Part 1
- Page 261 and 262: Printer Repair Flowcharts, Lane Dis
- Page 263 and 264: Printer Repair Sheet Distribution -
- Page 265 and 266: Printer Repair Sheet Transfer to Pa
- Page 267 and 268: Printer Repair Functional Descripti
- Page 269 and 270: Printer Repair 4. Begin Off Line (B
- Page 271 and 272: Printer Repair The following modes
- Page 273 and 274: Printer Repair 17. Calculation The
- Page 275: Printer Repair PF_GS01 - Technical
- Page 279 and 280: Printer Repair − The paper transp
- Page 281 and 282: Printer Repair ML_GS02 / MR_GS02 an
- Page 283 and 284: Printer Repair Layout dlabr205 Volt
- Page 285 and 286: Printer Repair Transport Unit TU Fu
- Page 287 and 288: Printer Repair Voltages + 5V Logic
- Page 289 and 290: Printer Repair Laser Module Warning
- Page 291 and 292: Printer Repair Connection of the po
- Page 293 and 294: Printer Repair PE_GS01, Layout dlab
- Page 295 and 296: Printer Repair Circuit Diagram dlab
- Page 297 and 298: Printer Repair Laser Remote After t
- Page 299 and 300: Printer Repair Test Points MP1 +5 +
- Page 301 and 302: Printer Repair LA_GS05 - Red Laser
- Page 303 and 304: Printer Repair Lane Distributor LD
- Page 305 and 306: Printer Repair LD_GS01 - Lane Distr
- Page 307 and 308: Printer Repair RD_GS01 - Back Print
- Page 309 and 310: Printer Repair Laser Module (LA) Th
- Page 311 and 312: Printer Repair Laser Sources Laser
- Page 313 and 314: Printer Repair There are 2 methods
- Page 315 and 316: Printer Repair − Enter new values
- Page 317: Printer Repair − Define the pixel
- Page 321 and 322: Printer Repair Mainboard Replacemen
- Page 323 and 324: Printer Repair − Determine the op
- Page 325 and 326: Printer Repair Download XILINKS (pr
Repair<br />
Printer<br />
Jumpers<br />
J1 not plugged in<br />
J2 not plugged in<br />
J3 plugged in Main clock for data pipeline (60,929170 MHz)<br />
J4 not plugged in<br />
J5 not plugged in The Jumper must not remain plugged in during normal operation!<br />
Only for the LEDs active, the operating conditions can be checked<br />
service: plugged in<br />
J6 plugged in CAN-termination resistor active<br />
LED Display<br />
D1 LED red Lights when the Reset line on the SPI Interface is active<br />
D2 LED red Initialisation FPGA (signal/INITX in the SP)<br />
D3 LED red Polygon facet not synchronous<br />
D4 LED red Picture error<br />
D33 LED yellow End of line (EOL), during Lineretrace<br />
D34 LED yellow Picture work, lights during the image output<br />
D35 LED yellow no significance<br />
D36 LED yellow FIFO empty latch<br />
lights when a communication error occurs with the LVDS interface<br />
D37 LED yellow FIFO almost full<br />
D38 LED yellow FIFO full latch, communication error with the LVDS interface<br />
Test Points<br />
MP3 +5V<br />
MP4 GND GND against +5V<br />
MP7 +5V (digital)<br />
MP8 +3,3V(digital)<br />
MP9<br />
Video output voltage Red channel<br />
MP10<br />
Video analogue GND<br />
MP11<br />
Video output voltage Blue channel<br />
MP12<br />
Video output voltage Green channel<br />
MP13<br />
Measuring voltage laser energy Green channel<br />
MP14<br />
DC-compensated amplified noise voltage Green channel (0...1,2...2,4V)<br />
MP15<br />
Measuring voltage laser voltage Blue channel<br />
MP16<br />
DC-compensated amplified noise voltage Blue channel (0...1,2...2,4V)<br />
MP23<br />
Not used<br />
ST33<br />
Test point for EOL signal<br />
ST34<br />
Test point for Picture Work<br />
Connector Allocation<br />
see Printer Mainboard in register 6.2<br />
<strong>AGFA</strong> d-<strong>lab.3</strong> 2001-01-02 /PN 9009 6.3.25