AGFA d-lab.3 Digital Compact Lab
AGFA d-lab.3 Digital Compact Lab AGFA d-lab.3 Digital Compact Lab
Scanner Repair Negative Carrier Removing the Negative Carrier Some parts, e.g. the film drive and rocker motors, are only accessible after removal of the negative carrier. Screwdriver Caution! Do not unscrew the red lacquer-sealed banjo bolts. − Unscrew the marked screws (arrows) − Lift off the negative carrier #negcar01 1 Banjo bolt: Do not touch! 2 Active film exit 4.4.14 2001-01-02 /PN 9009 AGFA d-lab.3
Repair Scanner Changing the Lifting Magnet, toothed Belt and auxiliary Drive Shaft Allen key Screwdriver Lifting magnet: − Unscrew the marked screws (grub screws) − Pull off the magnet Belt: − Pull off the additional gear incl. the armature plate − Change the belt Auxiliary drive shaft: − Unscrew the holder (3 screws) − Pull out the shaft; the bearings can be removed after the lock washer has been removed − Mind the correct position of the holder when mounting it again (see Figure) dlabr247 1 Magnet 2 Armature plate 3 Gear 4 Holder 5 Auxiliary drive shaft 6 Lock washer AGFA d-lab.3 2001-01-02 /PN 9009 4.4.15
- Page 123 and 124: Repair Scanner Functional Descripti
- Page 125 and 126: Repair Scanner Scanner Optic dlab14
- Page 127 and 128: Repair Scanner Main Scan Cycle Filt
- Page 129 and 130: Repair Scanner Filter Wheel LH_MO01
- Page 131 and 132: Repair Scanner The motor is energis
- Page 133 and 134: Repair Scanner Auxiliary Shutter (D
- Page 135 and 136: Repair Scanner Position Auxiliary D
- Page 137 and 138: Repair Scanner Amplifiers, function
- Page 139 and 140: Repair Scanner Lenses − Fixed foc
- Page 141 and 142: Repair Scanner Functions and Proper
- Page 143 and 144: Repair Scanner Film Drive NC_MO01 T
- Page 145 and 146: Repair Scanner Control The Motherbo
- Page 147 and 148: Repair Scanner FD/SD Output Stage (
- Page 149 and 150: Repair Scanner Functions: − Contr
- Page 151 and 152: Repair Scanner The TFS is not perfo
- Page 153 and 154: Repair Scanner CG Controller (CCD G
- Page 155 and 156: Repair Scanner Driver Sensor Board
- Page 157 and 158: Repair Scanner I 2 C Bus The 2-Bit
- Page 161 and 162: Repair Scanner Repair / Adjustments
- Page 163 and 164: Repair Scanner Shutter Toothed belt
- Page 165 and 166: Repair Scanner − Check the belt d
- Page 167 and 168: Repair Scanner 2-Film Feeder Dismou
- Page 169 and 170: Repair Scanner Installing the Feede
- Page 171 and 172: Repair Scanner Feeder rocker Feeler
- Page 173: Repair Scanner − Light sensor act
- Page 177 and 178: Repair Scanner 1a Cover plate A 1b
- Page 179 and 180: Repair Scanner Changing the Light S
- Page 181 and 182: Repair Scanner Replacing the Zoom /
- Page 183 and 184: Repair Scanner Precanner Adjustment
- Page 185 and 186: Repair Scanner Remove the following
- Page 187 and 188: Repair Scanner Scanner Calibration
- Page 189 and 190: Repair Scanner White Balance A whit
- Page 191 and 192: Repair Scanner Moment of Execution
- Page 193 and 194: Repair Main-PC Contents Overview ..
- Page 197 and 198: Repair Main-PC Overview Main-PC dla
- Page 199 and 200: Repair Main-PC Drives Drives (drive
- Page 201 and 202: Repair Main-PC PC Mainboard Connect
- Page 203 and 204: Repair Main-PC BIOS Settings AWARD
- Page 205 and 206: Repair Main-PC Operating System Win
- Page 207 and 208: Repair Main-PC Repair Removal of th
- Page 209 and 210: Repair Printer Contents General Ove
- Page 211 and 212: Repair Printer Removal, Installatio
- Page 215 and 216: Repair General Overview Sensors and
- Page 217 and 218: Printer Repair Electrical Structure
- Page 219 and 220: Printer Repair Voltages on the d-la
- Page 221: Printer Repair ■ 6.1.8 2001-01-02
Repair<br />
Scanner<br />
Changing the Lifting Magnet, toothed Belt and auxiliary Drive Shaft<br />
Allen key<br />
Screwdriver<br />
Lifting magnet:<br />
− Unscrew the marked screws (grub screws)<br />
− Pull off the magnet<br />
Belt:<br />
− Pull off the additional gear incl. the armature<br />
plate<br />
− Change the belt<br />
Auxiliary drive shaft:<br />
− Unscrew the holder (3 screws)<br />
− Pull out the shaft; the bearings can be removed<br />
after the lock washer has been removed<br />
− Mind the correct position of the holder when<br />
mounting it again (see Figure)<br />
dlabr247<br />
1 Magnet<br />
2 Armature plate<br />
3 Gear<br />
4 Holder<br />
5 Auxiliary drive shaft<br />
6 Lock washer<br />
<strong>AGFA</strong> d-<strong>lab.3</strong> 2001-01-02 /PN 9009 4.4.15