15.06.2014 Views

Operating Oil Drum Loader - Lionel

Operating Oil Drum Loader - Lionel

Operating Oil Drum Loader - Lionel

SHOW MORE
SHOW LESS

Create successful ePaper yourself

Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.

WIRING PROCEDURE<br />

If the wires are not already stripped, peel the insulation from the ends of the wires. (1/4” to 3/8” is sufficient, see Figure 4).<br />

Attach the ends of the wire to the spring clip, inserting the bare wire end, and releasing the tab (See Figure 5). Spring tension<br />

assures a tight wire contact.<br />

STRIPPING THE WIRE<br />

INSERTING WIRE INTO THE<br />

SPRING CLIP<br />

FIGURE 4 FIGURE 5<br />

Figure 6 and 7 demonstrate two methods of<br />

wiring the <strong>Oil</strong> <strong>Drum</strong> <strong>Loader</strong> to your layout. Use<br />

the one that best suits your needs.<br />

FOR LIGHTS AND MOTOR TO BE CONTROLLED BY THE SLIDE SWITCH<br />

Four wires and a slide switch are supplied with<br />

this set (although only three wires will be used<br />

in this operation) and should be attached as<br />

follows: First attach one wire to one of the<br />

clips on the lockon and attach the other end to<br />

one of the slide switch terminals. Attach a second<br />

wire to the other terminal on the slide<br />

switch and connect the other end of the wire to<br />

the No. 3 spring clip on the underside of the<br />

platform. Attach the third wire to the other clip<br />

on the lockon and attach the other end of the<br />

wire to the No. 2 spring clip on the underside<br />

of the platform. Now attach the two floodlight<br />

wires to the No. 2 and No. 3 spring clips as<br />

shown. Note: The two black wires on the<br />

underside of the platform have been factory<br />

assembled to terminals 2 and 3.<br />

UNDERSIDE OF THE OIL<br />

LOADER PLATFORM<br />

1<br />

2<br />

3<br />

OPEN<br />

Floodlight Tower<br />

Wires<br />

SLIDE SWITCH<br />

FIGURE 6<br />

FOR LIGHTS ON CONTINUOUSLY AND MOTOR ACTION CONTROLLED BY THE SLIDE SWITCH.<br />

Four wires will be used in this operation. First<br />

attach one wire to one of the clips on the lockon<br />

and attach the other end to one of the slide<br />

switch terminals. Attach a second wire to the<br />

other terminal on the slide switch and connect<br />

it to the No. 3 spring clip on the underside of<br />

the platform. Attach the third wire to the other<br />

clip on the lockon and connect the other end<br />

of the wire to the No. 2 spring clip on the<br />

underside of the platform. Attach the fourth<br />

wire to the lockon as shown and attach the<br />

other end of the wire to the No. one spring<br />

clip on the underside of the platform. Now<br />

attach the two floodlight wires to the No. 1 and<br />

No. 2 spring clips as shown. Note: The two<br />

black wires on the underside of the platform<br />

have been factory assembled to terminals 2<br />

and 3.<br />

3<br />

UNDERSIDE OF THE OIL<br />

LOADER PLATFORM<br />

1<br />

2<br />

3<br />

Floodlight Tower<br />

Wires<br />

SLIDE SWITCH<br />

FIGURE 7

Hooray! Your file is uploaded and ready to be published.

Saved successfully!

Ooh no, something went wrong!