Download - R&M Materials Handling equipment
Download - R&M Materials Handling equipment Download - R&M Materials Handling equipment
R&M Materials Handling, Inc. 4501 Gateway Boulevard Springfield, Ohio 45502 P.: (937) 328-5100 FAX: (937) 325-5319 STOP Stop button Stops the motor if keypad is the active control place ! WARNING! Changing parameter settings during running may cause a hazardous situation. Parameter settings must not be changed during running. ! WARNING! Driving via display may cause a hazardous situation. Panel control must not be used. 4.1.1 Navigation on the control keypad M8. STOP READY Fault History H1$Hxx $ H8.1. STOP READY 57 Thermistor F T1$T13 $ T8.1.1. I/O term I/O term I/O term STOP READY Operation days 0 M7. STOP READY I/O term Active Faults F0 M6. STOP READY I/O term System Menu S1$S9 $ S6.1. STOP READY I/O term Application Crane G5. STOP READY I/O term Panel Control B1$R2 $ B5.1. STOP READY I/O term Panel Control Off G4. STOP READY I/O term Monitoring G1$V19 $ V4.19. STOP READY I/O term Output Frequency 0.00 Hz G2. STOP READY Parameters G1$G3 $ G2.2. STOP READY Motor Parameters P1$P20 $ P2.2.1. I/O term I/O term I/O term STOP READY Motor Nom Volt 400 V 4.1.2 Value line editing P2.2.1. STOP READY I/O term Motor Nom Volt 400 V Mode change Edit value Accept value enter ! WARNING! Changing parameter settings during running may cause a hazardous situation. Parameter settings must not be changed during running. 28/79 This document and the information contained herein, is the exclusive property of R&M Materials Handling Inc. and represents a non-public, confidential and proprietary trade secret that may not be reproduced, disclosed to third parties, altered or otherwise employed in any manner whatsoever without the express written consent of R&M Materials Handling Inc. Copyright © (2005) R&M Materials Handling Inc. All rights reserved.
R&M Materials Handling, Inc. 4501 Gateway Boulevard Springfield, Ohio 45502 P.: (937) 328-5100 FAX: (937) 325-5319 4.2 Storing and restoring parameters 4.2.1 User parameters - File “User parameters” is stored in inverter’s control unit. - User parameters are recommended to save after final set up. - The whole parameterset can be stored to User parameters with parameter B 4.1.2. “Save User Par / Enter ”, press “->” “All param.” blinks on display, confirm with enter. - After restoring always check the motor parameters. 4.2.4 Factory settings - Factory settings are not used. 29/79 This document and the information contained herein, is the exclusive property of R&M Materials Handling Inc. and represents a non-public, confidential and proprietary trade secret that may not be reproduced, disclosed to third parties, altered or otherwise employed in any manner whatsoever without the express written consent of R&M Materials Handling Inc. Copyright © (2005) R&M Materials Handling Inc. All rights reserved.
- Page 1 and 2: English 2.11.2006 SERVICE MANUAL FO
- Page 3 and 4: R&M Materials Handling, Inc. 4501 G
- Page 5 and 6: R&M Materials Handling, Inc. 4501 G
- Page 7 and 8: Example layout R&M Materials Handli
- Page 9 and 10: R&M Materials Handling, Inc. 4501 G
- Page 11 and 12: R&M Materials Handling, Inc. 4501 G
- Page 13 and 14: R&M Materials Handling, Inc. 4501 G
- Page 15 and 16: R&M Materials Handling, Inc. 4501 G
- Page 17 and 18: R&M Materials Handling, Inc. 4501 G
- Page 19 and 20: R&M Materials Handling, Inc. 4501 G
- Page 21 and 22: R&M Materials Handling, Inc. 4501 G
- Page 23 and 24: R&M Materials Handling, Inc. 4501 G
- Page 25 and 26: R&M Materials Handling, Inc. 4501 G
- Page 27: R&M Materials Handling, Inc. 4501 G
- Page 31 and 32: R&M Materials Handling, Inc. 4501 G
- Page 33 and 34: R&M Materials Handling, Inc. 4501 G
- Page 35 and 36: R&M Materials Handling, Inc. 4501 G
- Page 37 and 38: R&M Materials Handling, Inc. 4501 G
- Page 39 and 40: R&M Materials Handling, Inc. 4501 G
- Page 41 and 42: R&M Materials Handling, Inc. 4501 G
- Page 43 and 44: R&M Materials Handling, Inc. 4501 G
- Page 45 and 46: R&M Materials Handling, Inc. 4501 G
- Page 47 and 48: R&M Materials Handling, Inc. 4501 G
- Page 49 and 50: R&M Materials Handling, Inc. 4501 G
- Page 51 and 52: R&M Materials Handling, Inc. 4501 G
- Page 53 and 54: R&M Materials Handling, Inc. 4501 G
- Page 55 and 56: 10.3.2 Fault Counter R&M Materials
- Page 57 and 58: R&M Materials Handling, Inc. 4501 G
- Page 59 and 60: R&M Materials Handling, Inc. 4501 G
- Page 61 and 62: R&M Materials Handling, Inc. 4501 G
- Page 63 and 64: R&M Materials Handling, Inc. 4501 G
- Page 65 and 66: R&M Materials Handling, Inc. 4501 G
- Page 67 and 68: R&M Materials Handling, Inc. 4501 G
- Page 69 and 70: R&M Materials Handling, Inc. 4501 G
- Page 71 and 72: R&M Materials Handling, Inc. 4501 G
- Page 73 and 74: R&M Materials Handling, Inc. 4501 G
- Page 75 and 76: R&M Materials Handling, Inc. 4501 G
- Page 77 and 78: R&M Materials Handling, Inc. 4501 G
R&M <strong>Materials</strong> <strong>Handling</strong>, Inc.<br />
4501 Gateway Boulevard<br />
Springfield, Ohio 45502<br />
P.: (937) 328-5100<br />
FAX: (937) 325-5319<br />
4.2 Storing and restoring parameters<br />
4.2.1 User parameters<br />
- File “User parameters” is stored in inverter’s control unit.<br />
- User parameters are recommended to save after final set up.<br />
- The whole parameterset can be stored to User parameters with parameter B 4.1.2.<br />
“Save User Par / Enter ”, press “->”<br />
“All param.” blinks on display, confirm with enter.<br />
- After restoring always check the motor parameters.<br />
4.2.4 Factory settings<br />
- Factory settings are not used.<br />
29/79<br />
This document and the information contained herein, is the exclusive property of R&M <strong>Materials</strong> <strong>Handling</strong> Inc. and represents a non-public, confidential and proprietary<br />
trade secret that may not be reproduced, disclosed to third parties, altered or otherwise employed in any manner whatsoever without the express written consent of R&M<br />
<strong>Materials</strong> <strong>Handling</strong> Inc. Copyright © (2005) R&M <strong>Materials</strong> <strong>Handling</strong> Inc. All rights reserved.
Change language