Stagemaker® SM2 Brochure - R&M Materials Handling equipment

®
SM2
Configuration A & B
High power packed into a compact model!
Stagemaker ® SM2 / Configuration A & B
Small But Powerful 1/4 Ton
» The Advantages of the SM5 in an SM1 body... In
the world of the scenic arts, theatre, concert halls,
exhibitions and trade shows you can now have the
advantages of:
• A motor that weighs 40% less*
• Compact dimension: down by 20%*
• 1/4 ton load that can be lifted from a single fall!
• 230V-3Ph-60Hz power supply
• Optional 208V-3Ph-60Hz power supply
* in comparison to SM5
www.stagemaker.com

SM2 — SMALL
BUT POWERFUL
LIGHT WEIGHT AND SMALL OVERALL DIMENSIONS*
* in comparison to SM5
Type
Capacity
Ton
Capacity
kg
Lifting Speed
ft/mn
(m/mn)
Falls Chain Motor
kW
Motor
hp
A
inch
(mm)
B
inch
(mm)
H
inch
(mm)
Weight
lb
(kg)
SM2 1/4 250 16 (4.8) 1 4x12 0.25 0.33 12.2 (310) 8.5 (216) 4.5 (112) 34 (17)
SM5 1/4 250 16 (4.8) 1 4.8x12.5 0.5 0.65 16.4 (417) 9.6 (247) 5.4 (137) 58 (263)
SM2 Configuration A:
Utilizes three-phase direct motor control best suited for
temporary or short-term set ups. Full line voltage controller
is furnished separately.
SM2 Configuration B:
Utilizes three-phase power and low voltage control. This
hoist can be used in temporary/short-term setups or
permanent installs when properly equipped.
Different models to suit any application
60 Hz 50 Hz Hoist Confi guration
Cap.
(Ton)
Cap.
(kg)
Frame
(Model)
Fall
Chain Size
(MM)
Motor
Power (HP)
Speed
(fpm)
Speed
(m/min)
Speed
(m/min)
A B C D E S V
1/16 60 SM1 1 3.1X9.3 0.33 32 9.6 8 • • •
1/16 60 SM1 1 3.1X9.3 0.33 64 19.2 16 • • •
1/8 125 SM1 1 3.1X9.3 0.16 16 4.8 4 •
1/8 125 SM1 1 3.1X9.3 0.33 32 9.6 8 • • •
1/4 250 SM2 1 4x12 0.33 16 4.8 4 • •
1/4 250 SM5 1 4.8X12.5 0.65 16 4.8 4 • • • •
1/4 250 SM5 1 4.8X12.5 1.3 32 9.6 8 • • •
1/4 250 SM5 1 4.8X12.5 1.3 64 19.2 16 • • •
1/4 250 SM10 1 6.8X17.8 2.8 64 19.2 16 •
1/2 500 SM5 1 4.8X12.5 0.65 16 4.8 4 • • • •
1/2 500 SM5 1 4.8X12.5 1.3 32 9.6 8 • • •
1/2 500 SM10 1 6.8X17.8 1.4 16 4.8 4 •
1/2 500 SM10 1 6.8X17.8 2.8 32 9.6 8 •
1/2 500 SM10 1 6.8X17.8 2.8 64 19.2 16 • • • •
1/2 500 SM10 1 6.8X17.8 2.8 4-64 1.2-19.2 1-16 •
1 1000 SM10 1 6.8X17.8 1.4 16 4.8 4 • • • •
1 1000 SM10 1 6.8X17.8 2.8 32 9.6 8 • • • •
1 1000 SM10 2 6.8X17.8 1.4 8 2.4 2 •
1 1000 SM10 2 6.8X17.8 2.8 16 4.8 4 •
1 1000 SM10 1 6.8X17.8 2.8 2-32 0.6-9.6 0.5-8 •
1.5 1600 SM16 1 9.0X27.0 5.6 32/8 9.6/2.4 8/2 †
2 2000 SM10 2 6.8X17.8 1.4 8 2.4 2 • • • •
2 2000 SM10 2 6.8X17.8 2.8 16 4.8 4 • • • •
2 2000 SM10 2 6.8X17.8 2.8 1-16 0.3-4.8 0.25-4 •
2 2000 SM20 1 9.0X27.0 5.6 32/8 9.6/2.4 8/2 †
2.5 2500 SM25 1 9.0X27.0 5.6 24/6 7.6/1.8 6.3-1.5 †
5 5000 SM25 2 9.0X27.0 5.6 12/3 3.8/0.9 3.2-0.75 †
• Configuration available in Normal position or Normal/
R&M Materials Handling, Inc. is a proud member of the following organizations:
Inverted position if specially equipped
† Configuration available in Normal position only
®
R&M Materials Handling, Inc.
4501 Gateway Boulevard
Springfi eld, Ohio 45502
PH: 937-328-5100
FAX: 937-325-5319
1-800-955-9967
To locate a distributor in your area,
please consult:
www.stagemaker.com
Stagemaker ® is a registered trademark of R&M Materials
Handling, Inc. R&M Materials Handling, Inc. may alter or
amend the technical specifications identified herein at
any time with or without notice.
© 2009, R&M Materials Handling, Inc. Bulletin# SM2/09