Resene Paints Masterspec Standard Specification

6711R 

RESENE PAINTING 

This specification has been written in good faith with information available at the time. It 

is assumed that the nominated applicator has the necessary experience and equipment 

to fulfil the requirements of this specification. If any substrate differs or is missing from 

this specification, please advise the writer of it. 

1. GENERAL 

Related work 

1.1 RELATED SECTIONS 

Refer to ~ for ~. 

Documents 

1.2 DOCUMENTS REFERRED TO 

Documents referred to in this section are: 

Health and Safety in Employment Act (Amended 1993) 

Occupational Health and Safety Service (OSH) publication: Guidelines to the provision of 

facilities and general safety in the construction industry. 

Occupational Health and Safety Service (OSH) publication: Guidelines for the management 

of lead-based paint. 

Report of the Asbestos Advisory Committee to the Minister of Labour – April 1999 

Documents listed above and cited in the clauses that follow are part of this specification. 

However, this specification takes precedence in the event of it being at variance with the 

cited document. 

1.3 MANUFACTURER’S DOCUMENTS 

Manufacturer’s and supplier’s documents relating to work in this section are: 

Resene One-Line Specifications and Product Data Manual 

Resene - Putting Your Safety First 

Copies of the above literature are available by phoning 0800 RESENE (0800 737 363) or 

visiting www.resene.co.nz. 

Requirements of the Contractor in the Completion of Defined Works 

1.4 CONTROL SAMPLES 

Prepare samples of the finished work, including the specified preparation if required by the 

architect or designer. Refer to 4. SCHEDULES. Obtain written approval from the 

Principal’s representative before proceeding. 

Use the Resene Architectural Sample Box as a basis of standard where appropriate. 

Control samples may, after written approval, be used for comparative testing of dry film 

thicknesses of the complete coating systems. 

1.5 SUPERVISED CONTROL SAMPLES 

Prepare samples of the finished work including the specified preparation. Refer to 4. 

SCHEDULES. Make arrangements for the full-time supervision of the application of each 

coat. Obtain written approval before proceeding. Control samples may, after written 

approval, be used for comparative testing of dry film thicknesses of the complete coating 

systems. 

1.6 QUALIFICATION 

Painters to be experienced competent workers, familiar with the materials and the 

techniques specified and with the Resene coating systems and be members of the 

Master Painters New Zealand Association Inc. 

6711R RESENE PAINTING Page 1

1.7 HEALTH AND SAFETY 

Comply with the requirements of the Health and Safety in Employment Act (Amended 

1993) and the Occupational Safety and Health Service (OSH) publication “Guidelines for 

the provision of facilities and general safety in the construction industry.” If the elimination 

or isolation of potential hazards is not possible, then minimise hazards in this work on site 

by using the proper equipment and techniques as required by the Painters Hazard 

handbook and Resene Putting Your Safety First handbook. The Contractor must supply 

protective clothing and equipment, inform the Principal’s representative as well as the 

employees and others on site of the hazards and put in place procedures for dealing with 

emergencies. 

Refer to the Occupational Safety and Health Service (OSH) publication “Guidelines for the 

management of lead-based paint” for the required procedures and precautions when: 

♦ 

Treating/removing lead-based paint; 

♦ 

Burning off lead-based paint; 

♦ 

Sanding off lead-based paint; 

♦ 

Using solventborne paint removers on lead-based paint. 

1.8 MATERIAL SAFETY DATA SHEETS 

Ensure all applicators have read the material safety data sheet for each product prior to use 

and comply with the required safety procedures. Material safety data sheets for all 

products can be obtained from Resene (ring 0800 RESENE, or access from 

www.resene.co.nz). Keep all sheets on site. 

Guarantees 

1.9 WARRANTY 

Warrant this work under normal conditions of use against failure. 

Warranty period - materials: According to 1(v) Durability of Paint Systems in the 

Resene One-Line Specifications and Product Data 

Manual 

Warranty period - execution: 3 years 

Refer to the PRELIMINARIES AND GENERAL section for the required form of warranty 

agreement and details of when completed warranty must be submitted. 

Performance 

1.10 RESENE INSPECTION 

Permit representatives of Resene to inspect the work in progress and to take samples of 

their products from site if requested. 

1.11 INSPECTION OF THE WORK 

Inspection of the whole of the work at each of the stages set out in 4. SCHEDULES may 

be made by the Principal’s representative. If inspection is required, agree on a programme 

that will facilitate such inspection, including notification when each part and stage of the 

work is ready for inspection prior to the work commencing. 

2. PRODUCTS 

Materials 

2.1 MATERIALS GENERALLY 

All coatings to be Resene products (which are guaranteed for consistency and 

performance under ISO 9001 and APAS) prepared, mixed and applied as directed in the 

Resene One-Line Specifications and Product Data Manual. 

Paint containers not in use are to have their lids or closures firmly affixed to prevent 

evaporation and contamination from foreign bodies. 


2.2 COLOURS 

Refer to AS/NZS 2311:2000 Guide to the painting of buildings, Section 1.9 Selection of 

Colour. 

Differently coloured paints will vary in price, opacity and durability. Colours need to be 

clearly identified before tendering to allow reasonable pricing that will consider both price 

and the number of coats needed to obtain opacity. Resene normally only specify two coats 

of colour but with certain colours, such as yellows and oranges, three coats may be 

needed. Your Resene representative will assist. 

Resene colours do vary in durability. Check with your local Resene representative if this is 

an important requirement of the job. Before any work commences painters should verify, 

with Architects or specifying authority, that their paint matches a previously supplied 

standard card or panel. The gloss level could also be checked at this stage. 

Large wall areas that require more than one container of paint per coat should have enough 

paint boxed together to complete the final coat. This will not apply if a single factory batch 

of paint, rather than shop tinted paint, is applied. 

Please ensure that the colour purchased is the same as selected. Resene accepts no 

responsibility for the application of incorrect colours. 

Darker colours over damp timber may result in faster than normal drying out and 

subsequent cracking. This may occur if timber is wet before painting or becomes wet for 

any reason at a later date. This should be taken into account when choosing colours. 

2.3 PAINT SYSTEMS 

EXTERIOR PAINT SYSTEMS 

Apply the listed Resene systems for the following substrates: 

Resene 

Spec. No. 

Prep Coat Resene products Finish 

EXTERIOR CEMENTITIOUS SURFACES 

1e 1.2 D83 TP Limelock D809 

1st SCS Concrete Primer D405 

P Sureseal D42 

2 nd Sonyx 101 D30 Waterborne semi-gloss 

Acrylic Undercoat D404 

Waterborne undercoat 

3 rd Sonyx 101 D30 Waterborne semi-gloss 

4 th Multishield + D54a (Optional) 

D83 1 st SP Sonyx 101 D30 




EXTERIOR TIMBERS 

2e 1.1 D82 1 st NRS Quick Dry D45 

TTS Wood Primer D40 

HO Sureseal D42 

2 nd Hi-Glo D31 Waterborne gloss 



3 rd Hi-Glo D31 Waterborne gloss 

EXTERIOR TIMBERS, STAINS AND CLEAR FINISHES 

2e 3.5 D82 1 st Waterborne Woodsman D57a Waterborne flat 

2 nd Waterborne Woodsman D57a Waterborne flat 

3 rd Waterborne Woodsman D57a (after 3 months) 

EXTERIOR TIMBER JOINERY 

3e 1.1 D82 & 1 st NRS Quick Dry D45 

TimberLock TTS Wood Primer D40 

D48 2 nd Enamacryl D309 Waterborne gloss 




3 rd Enamacryl D309 Waterborne gloss 

EXTERIOR TIMBER DECKS, PERGOLAS AND FENCES 

4e 1.3 D82 1 st NRS Lumbersider D34 

NSF Resitex Std D70 

2 nd Lumbersider D34 Waterborne satin 

3 rd Lumbersider D34 Waterborne satin 

5e EXTERIOR GALVANISED STEEL AND ZINCALUME 

5e 1.1 D89 1 st NW Galvo-Prime D402 

R Galvo One D41 



EXTERIOR FERROUS METALS 

6e 1.2 D801 1 st Rust Arrest RA30 

2 nd Rust Arrest RA30 

3 rd Lustacryl D310 Waterborne semi-gloss 

4 th Lustacryl D310 Waterborne semi-gloss 

EXTERIOR NON-FERROUS METALS 

7e 1.1 D89 1 st NRS Vinyl Etch RA31 

WNW Galvo-Prime D402 



EXTERIOR CEDAR 

8e 1.3 D82 & 1 st NC Quick Dry D45 

TimberLock WC Wood Primer D40 

D48 2 nd Lumbersider D34 Waterborne satin 




D82 & 1 st SP Lumbersider D34 Waterborne satin 

T/Lock 2 nd Lumbersider D34 Waterborne satin 

D48 3 rd Lumbersider D34 Waterborne satin 

EXTERIOR BITUMEN, BUTYL AND EPDM RUBBERS 

10e 1.1 D803 1 st Membrane Roofing Primer D49 



GLASS, GLAZED TILES, BAKED ENAMEL SYSTEMS 

11e 1.1 D802 or 1 st Smooth Surface Sealer D47 

D803 2 nd Hi-Glo D31 Waterborne gloss 




GLASS REINFORCED POLYESTER, EPOXY, PVC, ACRYLIC SHEETING, 

POLYSTYRENE, POLYCARBONATE 

12e 1.1 D803 1 st Hi-Glo D31 Waterborne gloss 




BRICK AND TERRACOTTA 

13e 1.3 D802 1 st SSP Lumbersider D34 Waterborne satin 




D802 1 st ES Sureseal D42 





EXTERIOR CANVAS AND AWNINGS 

16e 1.3 D803 1 st Lumbersider D34 Waterborne satin 



WATERPROOFING MEMBRANES 

17e 1.4 D83 TP: Limelock D809 

1 st SCS Concrete Primer D405 


SP X-200 D62 Waterborne low sheen 

2 nd X-200 D62 Waterborne low sheen 

3 rd X-200 D62 Waterborne low sheen 

4 th Multishield+ D54a (optional) 

HEAVY DUTY FLOOR COATINGS 

18e/i 2.1 U D83 1 st CS Armourcote 510 RA40* 

2 nd Uracryl 403 RA56 Solventborne gloss 

* Add Industrial SRG Grit to this coat for non-skid version. 

ANTI GRAFFITI SYSTEMS 

19e 2.1 CA D83 1 st Armourcote 510 RA47 

2 nd Uracryl 403 RA56 Pigmented 

3 rd Uracryl 403 RA56 Pigmented 

4 th Uracryl 403 RA56 Clear 

TEXTURED AND SPECIALIST COATINGS (Including Harditex) 

20e 1.3 RS D83 TP Limelock D809 



2 nd Lumbersider D34* 

3 rd Resitex D70 Waterborne textured 

4 th Multishield+ D54a (Optional) 

* For additional waterproofing, replace this coat with one coat of Resene X-200; for a higher DFT, 

replace this coat with one coat of Resene Resitex. 

PAINT EFFECTS 

21e/i 1.5 C 1 st IO Zylone Sheen x 2 D302 

E Lumbersider x 2 D34 

EWM X-200 x 2 D62 

TF Resitex x 2 D70 

3 rd Paint Effects Medium D307 Waterborne 

Flat - colourwashing 

EXTERIOR MILD STEELS, NEW FERROUS METALS 

(Medium and long-term protection) 

22e 2.1 EMT D801.1 1 st MT Zincilate 10 RA20 Inorganic zinc 

D801.8 

D801.7 

2 nd Armourcote 512 RA407 High build epoxy gloss 

EXTERIOR NEW HOT DIPPED GALVANISED MILD STEEL 


23e 2.1 ELT D89.1 1 st LT Vinyl Etch RA31 Etch primer 

D89.2 


EXTERIOR NEW METAL SPRAY COATINGS (METAL ARC OR ZINC SPRAY) 


24e 2.1 ULT * 1 st LT Armourcote 220 RA34 Epoxy primer 

2 nd Uracryl 403 RA56 Acrylic urethane 

3 rd Uracryl 403 RA56 Acrylic urethane 

4 th Uracryl 403 UVS Clear RA56 Acrylic urethane clear gloss 

* Refer to the Resene Engineered Coating Systems manual for preparation 

EXTERIOR METALLIC FINISHES 

Metallic finish on cementitious plaster 

25e 1.3/5 D83 1 st Quick Dry D45 

2 nd Lumbersider D34 

3 rd Enamacryl Metallic D309a Waterborne metallic 

4 th Enamacryl Metallic D309a Waterborne metallic 



INTERIOR PAINT SYSTEMS 

Apply the listed Resene systems for the following substrates: 


Spec. No. 


INTERIOR CEMENTITIOUS SURFACES 

1i 1.2 D83 TP Limelock D809 



2 nd Lustacryl D310 Waterborne semi-gloss 




D83 1 st SP Lustacryl D310 Waterborne semi-gloss 



INTERIOR TIMBER 

2i 1.1 D82 1 st NRS Quick Dry D45 



POV Smooth Surface Sealer D47 

2 nd Enamacryl D309 Waterborne gloss 




INTERIOR TIMBER, STAINS AND CLEAR FINISHES 

2i 4.1 D82 1 st SF Waterborne Colorwood D50a 

2 nd Polyflat D52* 

3 rd Polygloss D52 Solventborne gloss 

4 th Polygloss D52 Solventborne gloss 

* For particle and fibreboard, replace with one coat of Resene Aquaclear 

D82 1 st CF Waterborne Colorwood Reducing 

Base D50a (optional) 





D82 1 st HDF Polythane D53 

2 nd Polythane D53 

3 rd Polythane D53 Solventborne gloss 

4 th Polythane D53 Solventborne gloss 

* For particle and fibreboard, replace with one coat of Resene Particle Board Sealer. 

INTERIOR TIMBER JOINERY 

3i 1.1 D82 & 1 st NRS Quick Dry D45 


D48 POV Smooth Surface Sealer D47 





INTERIOR FERROUS METALS 

6i 1.1 D801 1 st Rust Arrest RA30 

2 nd Quick Dry D45 


4 th Enamacryl D309 Waterborne gloss 

INTERIOR NON-FERROUS METALS 

7i 1.1 D89 1 st NRS Vinyl Etch RA31 





INTERIOR GLASS, GLAZED TILES, FORMICA, POLYETHYLENE, POLYPROPYLENE 

AND BAKED ENAMEL SYSTEMS 

11i 1.1 D802 1 st Smooth Surface Sealer D47 

or D803 





INTERIOR GLASS REINFORCED POLYESTER, GLASS REINFORCED EPOXY, PVC, 

ACRYLIC SHEETING 

12i 1.1 D803 1 st Enamacryl D309 Waterborne gloss 




INTERIOR BRICK AND TERRACOTTA 

13i 1.2 D802 1 st SSP Lustacryl D310 Waterborne semi-gloss 




D802 1 st PCS Sureseal D42 





INTERIOR BRICK AND TERRACOTTA, CLEAR FINISHES 

13e/i 4.5 D802 1 st PS Aquapel D65 Solventborne flat 

2 nd Aquapel D65 Solventborne flat 

3 rd Aquapel D65 Solventborne flat 

INTERIOR PAPER FACED PLASTER/SOLID PLASTER/FIBROUS PLASTER 

15i 1.4 SCL4 D84, 1 st NRS Broadwall Acrylic Wallboard Sealer D403 

D85 

D87, D807 WSP Sureseal D42 

2 nd Zylone SpaceCote D311 Waterborne low sheen 



3 rd Zylone SpaceCote D311 Waterborne low sheen 

CANVAS, SCANDATEX AND HESSIAN 

16i 1.3 D803 1 st NRS Lumbersider D34 



D803 1 st SR Sureseal D42 





SPECIALIST FLOOR SYSTEMS 

18i 2.2 D83 1 st TS Wood Primer D40 

CS Sidewalk D38 

GCS Smooth Surface Sealer D47 

MPB Quick Dry D45 

2 nd Sidewalk D38* Solventborne semi-gloss 

3 rd Sidewalk D38 Solventborne semi-gloss 

* Add SRG Grit to this coat for non skid version 

ANTI GRAFFITI SYSTEMS 

19i 1.1 OA 1 st WBS Aquapoxy RA42 Pigmented 

2 nd Aquapoxy RA42 Pigmented 

3 rd Aquapoxy RA42 Pigmented 

TEXTURED COATINGS 

20e/i 1.5 D83/ TP Limelock D809 

D84 1 st SCS Concrete Primer D405 




3 rd Sandtex D71 Waterborne fine texture 

* For additional waterproofing replace this coat with one coat of Resene X-200; for a higher DFT, 

replace this coat with one coat of Resene Sandtex. 


D84 1 st SP Lumbersider D34 

2 nd Sandtex D71 Waterborne fine texture 


* For additional waterproofing replace this coat with one coat of Resene X-200; for a higher DFT, 


PAINT EFFECTS 



EWM X-200 x 2 D62 


3 rd Paint Effects Medium D307 Waterborne flat - 

colourwashing 

INTERIOR MILD STEELS 

22i 2.1 AF D801.1 1 st Armourcote 210 RA35 Alkyd primer 

D801.8 

D801.5 

or D801.7 

2 nd Armourcote 608 RA72 Alkyd gloss 

INTERIOR METALLIC FINISHES 

Waterborne metallic finish on Paperfaced Plasterboard 

25i 1.3/51 D84, 1 st Broadwall AWS D403 

D85 




5 th Aquaclear D59 (Optional) 

2.4 THINNERS/ADDITIVES 

Use only if and when expressly directed by Resene for their particular product in a 

particular application. 

Accessories 

2.5 ACCESSORIES 

Contact your local Resene ColorShop for a full range of accessories and usage advice. 

3. EXECUTION 

Conditions 

3.1 EXECUTION 

To conform with required trade practice, which shall be deemed to include those 

methods, practices and techniques contained in AS/NZS 2311:2000 Guide to the painting 

of buildings and the Occupational Safety and Health (OSH) publication: “Guidelines for 

the provision of facilities and general safety in the construction industry.” 

3.2 TREATED SURFACES 

Where surfaces have been treated with curing agents, preservatives, fire retardants, or 

similar, check with the treatment manufacturer that coating materials are compatible with 

the treatment and do not inhibit its performance. If they are not compatible, obtain 

instructions from the treatment manufacturer before proceeding. 

3.3 ANCILLARY SURFACES 

The descriptions of areas to be coated given in schedules and elsewhere are of necessity 

simplified. Coat all ancillary exposed surfaces to match similar or adjacent materials or 

areas, except where a fair-faced natural finish is required or items are completely 

prefinished. In cases of doubt obtain written instructions from the Principal’s 

representative before proceeding. 


The Contractor must complete any work obviously necessary for the proper and entire 

completion of the contract even if not specifically covered by this specification without 

extra cost to the Principal. 

3.4 HARDWARE 

Do not paint hinges or hardware that cannot be removed. Before commencing work 

carefully remove hardware, fixtures and fittings, set aside where they cannot be damaged 

or misplaced and replace on completion. Refer to 4. SCHEDULES for hardware, fixtures 

and fittings for removal. 

3.5 PROTECTION 

Supply, lay and fix all dropsheets, coverings and masking necessary to protect nonspecified 

surfaces, adjoining, fixtures, fittings and spaces from paint drops, spots, spray 

and damage. 

Application - preparatory work 

3.6 SURFACE PREPARATION 

Refer to the Resene One-Line Specifications and Product Data Manual for surface 

preparation sheets (or obtain them by calling 0800 RESENE, or from the Resene website 

www.resene.co.nz) listed in the materials systems schedule clauses. Carry out all the 

preparatory work required by them for each of the substrates. 

Use Resene Broadwall Surface Prep. as a surfacer to achieve a Level 5 finish on interior 

wallboards. 

3.7 LEAD-BASED PAINT, ASBESTOS 

If present, handle lead-based paint and asbestos as required by the Resene Putting Your 

Safety First booklet and the Occupational Safety and Health (OSH) publication: Guidelines 

for the management of lead-based paint. 

For further information read “Report of the Asbestos Advisory Committee to the Minister 

of Labour – April 1999” or contact Resene. Removal and/or disposal of asbestos 

containing materials may require special permission and a license. Contact your local 

Council office to determine your obligations under their bylaws. 

3.8 SHARP EDGES, CRACKS AND HOLES 

For timber refer to AS/NZS 2311:2000 Guide to the painting of buildings, Section 3.2.2 

Standard of Finish. 

Sand sharp edges on timber to a rounded profile to ensure adequate paint cover. Apply a 

stripe coat of each specified coating on steelwork sharp edges and welds, in addition to the 

specified coat, to achieve the correct film build and maximise the potential of the paint 

system. Sand, grind or file sharp edges on other substrates to a rounded profile where 

practicable. 

3.9 REMEDIAL WORK 

If any substrate or surface, that even with the preparation work called for in this section, 

cannot be brought up to a standard that will allow painting or clear finishing of the 

required standard then do not proceed until remedial work is carried out. 

3.10 GAP FILLING 

Refer to AS/NZS 2311:2000 Guide to the painting of buildings, Section 7.3.3 Gap Filling. 

Thoroughly clean and prepare cracks, holes, indented and damaged surfaces for filling. A 

special primer is needed with many substrates, while on others the filler can interfere with 

the coating. Check carefully and only use fillers in strict accordance with the manufacturer’s 

directions. Elastomeric sealants that can tolerate 30% movement should only be used 

where gaps exist between different substrates or for expansion joints. Do not use 

elastomeric sealants for general hole filling. Do not paint over elastomeric sealants 

because they are liable to bleed plasticiser and are much more flexible than the paint. 


Fillers such as Resene Jointflex or Resene Epox-O-Bond Epoxy Filler are recommended 

on exterior concrete and interior concrete in wet areas. 

Where sealants are required, check with the sealant manufacturer regarding correct 

priming and that overcoating materials are compatible with the sealant and do not inhibit 

its performance. If they are not compatible, obtain instructions from the sealant 

manufacturer before proceeding. 

3.11 OFF SITE WORK 

Carry out all this work, where possible under cover, in a suitable environment with suitable 

lighting. Store all items, both before and after coating, in a clean, dry area protected from 

the weather and mechanical damage, properly stacked and spaced to allow air circulation 

and to prevent sticking. 

3.12 PRIMING JOINERY 

Refer to AS/NZS 2311:2000 Guide to the painting of buildings, Section 3.2.8 Machine 

Priming of Timber and Section 3.2.10 Effect of Timber Species. 

Ensure L.O.S.P. treated joinery has dried sufficiently to lose all solvent odour. Pre-treat 

bare timber with Resene TimberLock (Data Sheet D48) to improve the durability of 

subsequent coats. Allow Resene TimberLock to dry for 24 hours then wipe off any still 

tacky material with a Turps wet rag. Liberally coat end grain, allow to soak in and then 

recoat. After Resene TimberLock has dried, prime with Resene Wood Primer or Resene 

Quick Dry Acrylic Primer Undercoat. 

3.13 CONCEALED JOINERY SURFACES 

Where off-site coatings are specified they must be applied to all surfaces especially 

including those concealed when incorporated into the building. 

3.14 CONCEALED METAL SURFACES 

Apply primer to all surfaces that will be concealed when incorporated into the building. 

3.15 EXTERNAL DOORS 

Prime or seal and paint all edges before hanging. 

3.16 BEAD GLAZING 

Joinery to be stained, varnished, or painted to have the first two coats, or the primer and 

one undercoat, applied to rebates and beads before glazing. This is especially important 

with clears. Resene TimberLock is strongly recommended, particularly if there is a risk of 

water ponding. 

3.17 PUTTY FRONTING 

According to the putty manufacturer's instructions allow putty to harden, then prime with 

Resene Wood Primer (Data Sheet D40) or Resene Quick Dry Acrylic Primer Undercoat 

(Data Sheet D45). Fully protect the putty by completing the Resene coating system as 

soon as it is sufficiently firm. 

Application - generally 

3.18 PAINTING GENERALLY 

Comply with the Resene One-Line Specifications and Product Data Sheets, product labels 

and the additional requirements of this work section. 

All paints must be brought onto the job by the Contractor in their original sealed containers 

and be made available for inspection prior to application. Any materials supplied by the 

Contractor that differ from the material specified in this contract must be immediately 

removed from the job by the Contractor upon the Contractor being requested to do so. 

No painting shall begin on any area until the approval of the Principal’s representative is 

given. 


3.19 MIXING 

All paints to be thoroughly mixed. Incorporate any settled pigment and ensure the paint 

is homogenous. 

3.20 ENVIRONMENT 

Refer to AS/NZS 2311:2000 Guide to the painting of buildings, Section 6.3 Climatic 

Conditions. 

Defer painting of exterior surfaces until weather conditions are favourable - warm dry 

days without frost or heavy dews are preferred. Avoid painting in direct sunlight any 

surfaces that absorb heat excessively. 

Do not apply paint if the surface is less than 5°C above dew point, the relative humidity 

exceeds 85% (unless special precautions are taken to ensure that the surface is at least 

5°C above the temperature of the surrounding air), there is moisture or ice visible on the 

substrate or if any of these conditions are likely to occur before the paint has dried. 

As far as possible, apply paint in the temperature range 15°C to 25°C. If temperatures 

fall outside the range of 10°C and 35°C do not paint unless paints with the necessary 

temperature tolerances have been specified. 

The Principal’s representative may order painting to cease if, despite all conditions being 

met, there is a likelihood of frost or dew. The Contractor may propose protective 

measures against frost and these measures will be subject to the approval of the 

Principal’s representative. 

3.21 SEQUENCE OF OPERATIONS 

Painting work to generally follow the following sequence: 

• Complete all surface preparation before commencing painting; 

• Apply primers, sealers, stains, undercoats, paints and clear coatings in the 

sequences laid down by Resene; 

• Allow the full drying time between coats laid down by Resene; 

• Do not expose primers, undercoats and intermediate coats beyond a few days 

before applying the next coat. Refer to appropriate data sheets for recommended 

recoat times; 

• Finish broad areas before painting trim; 

• Ensure batch numbers of tins are matched for whole areas; 

• Internally, paint ceilings before walls and walls before joinery, trim and other items. 

3.22 APPLICATION 

Refer to AS/NZS 2311:2000 Guide to the painting of buildings, Section 8.7 Methods of 

Application. 

Select brush, roller, pad or spray and apply coatings to the recommendations of Resene to 

obtain a coating of the specified thickness, uniform gloss, surface finish and colour. Refer 

to the appropriate product data sheet and can label for appropriate application methods. 

3.23 LIGHTLY SAND 

Lightly sand primers, sealers, undercoats and intermediate coats to remove dust pick-up, 

protruding fibres and coarse particles. Complete by removing dust immediately before 

applying the next coat. 

3.24 DEFECTIVE WORK 

Immediately correct at own cost any defective work and recoat as required, following 

precisely the Resene system being applied. 

3.25 LOSS OR DAMAGE 

The Contractor shall be responsible for any loss or damage that may be caused to the 

property of the Owner in the carrying out of this contract. The Contractor shall make good 

such loss or damage at he Contractor’s own expense, to the satisfaction of the Owner. 


3.26 EACH COAT 

Each coat of paint and the completed paint system to have the following qualities and 

properties: 

• Uniform finish, colour, texture, sheen and hiding power and the proper number of 

coats applied; 

• No blemishes such as runs, sags, crinkling, fat edges, entrained paint skins, hairs, 

dust, bare or starved patches, cracks, brush marks, ladder marks and blistering; 

• Proper covering of corners, crannies, thin edges, cracks, end grains and other 

difficult places of application. 

Completion 

3.27 CLEAN 

Clean all adjoining surfaces, glass and fittings of any paint contamination. Clean 

adjoining glass to a shining finish. 

3.28 LEAVE 

Leave the whole of this work uniform in gloss and colour, of correct thickness, free from 

all painting defects, clean and unmarked and to the standard required for all following 

trades. 

3.29 REMOVE 

Remove all dropsheets, coverings and masking to leave surrounding surfaces and areas 

clean, tidy and undamaged. Remove all debris, unused materials and elements from the 

site. 

3.30 REPLACE 

Replace all hardware without damage to it or the adjoining surface and leave hardware 

properly fitted and in working order. 

4. SCHEDULES 

Prepare surfaces and apply Resene paints in accordance with the attached paint system 

specifications. 

4.1 CONTROL SAMPLES 

Substrate 

Resene One-Line number 

~ ~ 

4.2 SUPERVISED CONTROL SAMPLES 

Substrate 

Resene One-Line number 

~ ~ 

4.3 INSPECTION OF THE WORK 

Coating System 

Inspection at completion of 

~ ~ 

4.4 HARDWARE 

Hardware for removal: ~ 

Paint system schedules 

4.5 EXTERIOR FINISHES 

Substrate Resene number Colour 

Weatherboards ~ 

Timber Joinery/Fascias/Barges 

Timber Deck 

Concrete Masonry 

4.6 INTERIOR FINISHES 

Room name Number Substrate Resene number Colour 

Living G02 Ceiling - Plasterboard ~ 

Exposed Rafters 

Walls - Plasterboard 


Trim - Timber 

Doors - Paint Finish 

Dining G03 Ceiling - Plasterboard 

Exposed Rafters 

Walls - Plasterboard 

Timber Panelling 

Trim - Timber 

Doors - Paint Finish 

1e EXTERIOR CEMENTITIOUS SURFACES 

Resene Prep Coat Resene products Finish 

Spec. No. 

















D83 TP Limelock D809 

1 st SP Sonyx 101 D30 Waterborne semi-gloss 












D83 TP Limelock D809 

1 st SP Lumbersider D34 Waterborne satin 







2 nd Acrylic Undercoat D404 

3 rd Super Gloss D32 Solventborne gloss 

2e EXTERIOR TIMBERS 


Spec. No. 
















Spec. No. 


















2e EXTERIOR TIMBERS, STAINS AND CLEAR FINISHES 


Spec. No. 




2e 4.5 D82 1 st Woodsman D57 Solventborne flat 

2 nd Woodsman D57 Solventborne flat 

3 rd Woodsman D57 (after 3 months) 

3e EXTERIOR TIMBER JOINERY 


Spec. No. 









D48 2 nd Lustacryl D310 Waterborne semi-gloss 






D48 2 nd Acrylic Undercoat D404 


4e EXTERIOR TIMBER DECKS, PERGOLAS AND FENCES 


Spec. No. 

4e 1.3 D82 1 st NRS Lumbersider D34 

NSF Resitex Std D70 



4e 3.5 D82 1 st SF Waterborne Woodsman D57a Waterborne flat 



4e 4.5 D82 1 st Woodsman D57 Solventborne flat 



4e 4.5 D D82 1 st Kwila Decking Stain D501 Solventborne flat 



Spec. No. 


2 nd Kwila Decking Stain D501 Solventborne flat 

5e EXTERIOR GALVANISED STEEL AND ZINCALUME 


Spec. No. 













5e 2.1 D89 1 st Galvo One D41 



6e EXTERIOR FERROUS METALS 


Spec. No. 









6e 2.1 D801 1 st NRS Rust Arrest RA30 


3 rd Acrylic Undercoat D404 

4 th Super Gloss D32 Solventborne gloss 

1 st HDS Alumastic RA402 


3 rd Uracryl 403 RA56 Solventborne gloss 

6e 2.2 D801 1 st HDS Alumastic RA402 

2 nd Uracryl 402 RA55 Solventborne semi-gloss 

3 rd Uracryl 402 RA55 Solventborne semi-gloss 

7e EXTERIOR NON-FERROUS METALS 


Spec. No. 



2 nd Hi-Glo D31* Waterborne gloss 

3 rd Hi-Glo D31* Waterborne gloss 

* For doors, windows and joinery, use Resene Enamacryl D309 in place of Resene Hi-Glo. 



2 nd Sonyx 101 D30* Waterborne semi-gloss 

3 rd Sonyx 101 D30* Waterborne semi-gloss 

* For doors, windows and joinery, use Resene Lustacryl D310 in place of Resene Sonyx 101. 





Spec. No. 







D89 1st HDF Vinyl Etch RA31 

2nd Uracryl 403 RA56 Solventborne gloss 

3rd Uracryl 403 RA56 Solventborne gloss 

7e 2.2 D89 1 st Vinyl Etch RA31 



7e 2.4 D89 1st Vinyl Etch RA31 

2nd Uracryl 404 RA59 Solventborne low sheen 

3rd Uracryl 404 RA59 Solventborne low sheen 

8e EXTERIOR CEDAR 


Spec. No. 









D48 2 nd Sonyx 101 D30 Waterborne semi-gloss 










D82 & 1 st SP Lumbersider D34 Waterborne satin 

T/Lock 2 nd Lumbersider D34 Waterborne satin 






8e 3.5 D82 1 st SF Waterborne Woodsman D57a Waterborne flat 



8e 4.5 D82 1 st SF Woodsman D57 Solventborne flat 



D82 1st KS Kwila Decking Stain D501 Solventborne flat 

2nd Kwila Decking Stain D501 Solventborne flat 

9e EXTERIOR TOTARA AND MATAI TIMBER ONLY 


Spec. No. 

9e 1.1 D82 1 st Quick Dry D45 

2 nd Hi-Glo D31* Waterborne gloss 



3 rd Hi-Glo D31* Waterborne gloss 



Spec. No. 



2 nd Sonyx 101 D30* Waterborne semi-gloss 



3 rd Sonyx 101 D30* Waterborne semi-gloss 






D82 1 st SP Lumbersider D34 Waterborne satin 






9e EXTERIOR TOTARA AND MATAI TIMBER, STAINS AND CLEAR FINISHES 


Spec. No. 




9e 4.5 D82 1 st Woodsman D57 Solventborne Flat 

2 nd Woodsman D57 Solventborne Flat 


10e EXTERIOR BITUMEN, BUTYL AND EPDM RUBBERS 


Spec. No. 







10e 1.3 D803 1 st NRS Membrane Roofing Primer D49 



D803 1 st NSF Membrane Roofing Primer D49 

2 nd Resitex (Std) D70 Waterborne texture 

3 rd Resitex (Std) D70 Waterborne texture 

11e GLASS, GLAZED TILES, BAKED ENAMEL SYSTEMS 


Spec. No. 







D803 2 nd Sonyx 101 D30 Waterborne semi-gloss 











Spec. No. 


D803 2 nd Acrylic Undercoat D404 Waterborne undercoat 


12e GLASS REINFORCED POLYESTER, EPOXY, PVC, ACRYLIC SHEETING, 

POLYSTYRENE, POLYCARBONATE 


Spec. No. 





12e 1.2 D803 1 st Sonyx 101 D30 Waterborne semi-gloss 








12e 2.1 D803 1 st Smooth Surface Sealer D47 

2 nd Acrylic Undercoat D404 Waterborne undercoat 


13e BRICK AND TERRACOTTA 


Spec. No. 

13e 1.1 D802 1 st SSP Hi-Glo D31 Waterborne gloss 









13e 1.2 D802 1 st SSP Sonyx 101 D30 Waterborne semi-gloss 









13e 1.3 D802 1 st SSP Lumbersider D34 Waterborne satin 









13e 2.1 D802 1 st SSP Quick Dry D45 

ES Sureseal D42 



13e/i 3.1 D802 1 st IO Aquaclear D59 Waterborne gloss 

2 nd Aquaclear D59 Waterborne gloss 

3 rd Aquaclear D59 Waterborne gloss 

D802 SE Aquapel D65 

1 st EI Multishield+ D54a Waterborne gloss 

2 nd Multishield+ D54a Waterborne gloss 

3 rd Multishield+ D54a Waterborne gloss 



Spec. No. 


13e/i 4.1 D802 SE Aquapel D65 

1 st NRS F.10 Glaze D56 Solventborne gloss 

2 nd F.10 Glaze D56 Solventborne gloss 

3 rd F.10 Glaze D56 Solventborne gloss 


1 st HDS Uracryl 403 RA56 Solventborne gloss 




1 st HDS Uracryl 402 RA55 Solventborne semi-gloss 






14e CLEAR FINISHES ON CLAY TILES, ABSORBENT TILES, STONE AND SLATE, 

DECORATIVE AGGREGATE FLOORING 


Spec. No. 


1 st LDF F.10 Glaze D56 Solventborne gloss 




1 st HDF Uracryl 403 RA56 Solventborne gloss 




1 st IMC Polythane D53 Solventborne gloss 

2 nd Polythane D53 Solventborne gloss 



1 st HDF Uracryl 402 RA56 Solventborne semi-gloss 



16e EXTERIOR CANVAS AND AWNINGS 


Spec. No. 



16e 1.2 D803 1 st Sonyx 101 D30 Waterborne semi-gloss 




16e 2.5 D803 1 st Aquapel D65 Solventborne flat 


17e WATERPROOFING MEMBRANES 


Spec. No. 

17e 1.2 T D83 TP Limelock D809 

1 st Concrete Primer D405 


SP Thixalon 5 D63 Waterborne semi-gloss 

2 nd Thixalon 5 D63 Waterborne semi-gloss 



Spec. No. 


3 rd Thixalon 5 D63 Waterborne semi-gloss 


17e 1.2 F D83 TP Limelock D809 



SP Flexicover E D64 Waterborne semi-gloss 

2 nd Flexicover E D64 Waterborne semi-gloss 

3 rd Flexicover E D64 Waterborne semi-gloss 

4 th Lumbersider D34 (optional) 




SP X-200 D62 Waterborne low sheen 

2 nd X-200 D62 Waterborne low sheen 

3 rd X-200 D62 Waterborne low sheen 


18e HEAVY DUTY FLOOR COATINGS 


Spec. No. 

18e 1.5 B D83 1 st BS Blacktop D304 Waterborne flat 

Blacktop D304 

(optional) 

18e 1.5 T D83 1 st BS Membrane Roof Primer D49 

CS Tennis Court Coating D303 


2 nd Tennis Court Coating D303 Waterborne flat 

3 rd Tennis Court Coating D303 Waterborne flat 

18e/i 2.1 U D83 1 st CS Armourcote 510 RA40* 


18e/I 2.2 D83 1 st CS Armourcote 510 RA40* 


18e 4.5 D83 1 st CS Concrete Stain D58 Solventborne flat 

2 nd Concrete Stain D58 Solventborne flat 

* Add Industrial SRG Grit to this coat for non-skid version. 

19e ANTI GRAFFITI SYSTEMS 


Spec. No. 

19e 2.1 CS D83 1 st Armourcote 510 RA40 

2 nd Imperite 413 RA57 Pigmented 

3 rd Imperite 390 RA57 Clear 

19e 4.1 CS D83 1 st Imperite 390 RA57 Clear 

2 nd Imperite 390 RA57 Clear 

3 rd Imperite 390 RA57 Clear 

19e 2.1 CA D83 1 st Armourcote 510 RA47 




19e 4.1 CA D83 1 st Uracryl 403 RA56 Clear 

2 nd Uracryl 403 RA56 Clear 

3 rd Uracryl 403 RA56 Clear 

19e 2.1 PA D83 1 st Quick Dry D45 



4 th Uracryl 403 RA56 Pigmented 




Spec. No. 

19e 2.1 OS D83 1 st Smooth Surface Sealer D47 

2 nd Imperite 413 RA57 Pigmented 

3 rd Imperite 413 RA57 Pigmented 

4 th Imperite 390 RA57 Clear 

19e 2.1 OA D83 1 st Smooth Surface Sealer D47 




19e 2.1 TA D83 1 st Quick Dry D45 



4 th Uracryl 403 RA56 Pigmented 


19e 4.1 SA D83 1 st Uracryl 403 RA56 Clear over pigmented 

19e 4.1 SA D83 1 st Imperite 390 RA57 Clear over pigmented 

20e TEXTURED AND SPECIALIST COATINGS (INCLUDING HARDITEX) 


Spec. No. 

20e 1.2 T D83 1 st TP Limelock D809 

SCS Concrete Primer D405 


SP Thixalon 5 D63 

2 nd Thixalon 5 D63 Waterborne semi-gloss 

3 rd Thixalon 5 D63 (Optional) 


20e 1.2 F D83 TP Limelock D809 



SP Flexicover E D64 

2 nd Flexicover E D64 Waterborne semi-gloss 

3 rd Flexicover E D64 (Optional) 

4 th Lumbersider D34 

or Multishield+ D54a 

(Optional pigmented) 

(Optional clear) 

20e 1.3 RCM D83 TP Limelock D809 








20e 1.3 RS D83 TP Limelock D809 








20e 1.3 H D806 1 st Galvo Prime D402 (Spot prime) 

2 nd X-200 D62 



20e/i 1.3 P D83 TP Limelock D809 



CB Refer Rockcote Systems 

2 nd Plastercote D72* Waterborne textured 



Spec. No. 

3 rd Plastercote D72 Waterborne textured 


* This coat of Resene Plastercote can be replaced with one coat of Resene Sandtex if desired. 

Some applicators may find Sandtex easier to apply 


1 st PC Aquapel D65 

SSP AquaShield D601 Waterborne textured 

2 nd AquaShield D601 Waterborne textured 

3 rd AquaShield D601 Waterborne textured 





3 rd Sandtex D71 Waterborne textured 





2 nd Sandtex D71 Waterborne textured 

3 rd Sandtex D71 Waterborne textured 

21e PAINT EFFECTS 


Spec. No. 



EWM X-200 x 2 D62 



Flat - colourwashing 

21eli 1.5 R 1st IO Zylone Sheen x 2 D302 


EWM X-200 x 2 D62 


3rd Paint Effects Medium D307 Waterborne Flat - ragging 

21eli 1.5 S 1 st IO Zylone Sheen x 2 D302 


EWM X-200 x 2 D62 


3 rd Paint Effects Medium D307 Waterborne Flat - sponging 

21eli 1.5 L 1 st IO Zylone Sheen x 2 D302 


EWM X-200 x 2 D62 



Flat - limewash effect 

22e EXTERIOR MILD STEELS, NEW FERROUS METALS 

(MEDIUM AND LONG-TERM PROTECTION) 


Spec. No. 

22e 2.1 EMT D801.1 1 st MT Zincilate 10 RA20 Inorganic zinc 

D801.8 

D801.7 


22e 2.2 EMT D801.1 

D801.8 

D801.7 

1 st MT Zincilate 10 RA20 Inorganic zinc 

2 nd Armourcote 510 RA40 High build epoxy semi-gloss 



Spec. No. 

22e 2.1 UMT D801.1 

D801.8 

D801.7 



2 nd Armourcote 510 RA40 High build epoxy 

3 rd Uracryl 403 RA56 Acrylic urethane gloss 

22e 2.1 ELT D801.1 

D801.8 

D801.7 

1 st LT Zincilate 10 RA20 Inorganic zinc 


22e 2.1 ULT D801.1 

D801.8 

D801.7 

22e 2.2 UMT D801.1 

D801.8 

D801.7 






3 rd Uracryl 402 RA55 Acrylic urethane semi-gloss 

22e 2.2 ELT D801.1 

D801.8 

D801.7 



22e 2.2 ULT D801.1 

D801.8 

D801.7 

22e 2.3 MFMT D801.1 

D801.8 

D801.7 

22e 2.3 MFLT D801.1 

D801.8 

D801.7 

22e 2.4 UMT D801.1 

D801.8 

D801.7 

22e 2.4 ULT D801.1 

D801.8 

D801.7 






3 rd Imperite IF 503 Metallic RA81 Acrylic epoxy satin metallic 






3 rd Uracryl 404 RA59 Acrylic urethane low sheen 




23e EXTERIOR NEW HOT DIPPED GALVANISED MILD STEEL 



Spec. No. 

23e 2.1 ELT D89.1 1 st LT Vinyl Etch RA31 Etch primer 

D89.2 


23e 2.1 ULT D89.1 

D89.2 

1 st LT Vinyl Etch RA31 Etch primer 



Spec. No. 



3rd Uracryl 403 RA56 Acrylic urethane gloss 

23e 2.2 ELT D89.1 

D89.2 

23e 2.2 ULT D89.1 

D89.2 

23e 2.3 MFLT D89.1 

D89.2 

23e 2.4 ULT D89.1 

D89.2 




2 nd Armourcote 510 RA40 High build epoxy acrylic 

urethane semi-gloss 

3 rd Uracryl 402 RA55 







24e EXTERIOR NEW METAL SPRAY COATINGS (METAL ARC OR ZINC SPRAY) 



Spec. No. 




4 th Uracryl 403 UVS Clear RA56 Acrylic urethane clear gloss 




4 th Uracryl 402 UVS Clear RA55 Acrylic urethane clear semigloss 




4 th Uracryl 404 UVS Clear RA59 Acrylic urethane clear low 

sheen 

* Refer to the Resene Engineered Coating Systems manual for preparation 

25e EXTERIOR METALLIC FINISHES 


Spec. No. 

Metallic finish on cementitious plaster 

25e 1.3/5 D83 1 st Quick Dry D45 





25e 1.3/5P D83 1 st Quick Dry D45 



4 th Pearl Shimmer D312 Waterborne pearlescent 


Metallic finish on concrete floor 

25e 2.3/5 D83 1 st Armourcote 510 RA40 

2 nd Imperite IF 503 RA81 Solventborne metallic 

3 rd Uracryl 400 Series Clear Acrylic urethane 

1i INTERIOR CEMENTITIOUS SURFACES 



Spec. No. 















D83 1 st SP Lustacryl D310 Waterborne semi-gloss 













1i 1.4 ZS D83 TP Limelock D809 



2 nd Zylone Sheen D302 Waterborne low sheen 



3 rd Zylone Sheen D302 Waterborne low sheen 

D83 1 st SP Zylone Sheen D302 Waterborne low sheen 



1i 1.4 SC D83 TP Limelock D809 







D83 1 st SP Zylone SpaceCote D311 Waterborne low sheen 






2 nd Zylone 20 D37 Waterborne flat 



3 rd Zylone 20 D37 Waterborne flat 

D83 1 st SP Zylone 20 D37 Waterborne flat 










Spec. No. 




2 nd Lusta-Glo D33 Solventborne semi-gloss 



3 rd Lusta-Glo D33 Solventborne semi-gloss 




2 nd Flatcote D306 Solventborne flat 



3 rd Flatcote D306 Solventborne flat 

2i INTERIOR TIMBER 


Spec. No. 




























2i 1.4ZS D82 1 st NRS Quick Dry D45 








D82 1 st SP Zylone Sheen D302 Waterborne low sheen 



2i 1.4SC D82 1 st NRS Quick Dry D45 








D82 1 st SP Zylone SpaceCote D311 Waterborne low sheen 





Spec. No. 










D82 1 st SP Zylone 20 D37 Waterborne flat 

























2i INTERIOR TIMBER, STAINS AND CLEAR FINISHES 


Spec. No. 




4 th Aquaclear D59 Waterborne gloss 


D82 1 st CF Waterborne Colorwood 

Reducing Base D50a 

(Optional) 






2 nd Aquaclear D59 Waterborne semi-gloss 

3 rd Aquaclear D59 Waterborne semi-gloss 

4 th Aquaclear D59 Waterborne semi-gloss 




(Optional) 






2 nd Aquaclear D59 Waterborne satin 

3 rd Aquaclear D59 Waterborne satin 



Spec. No. 


4 th Aquaclear D59 Waterborne satin 




(Optional) 












(Optional) 

2 nd Polyflat D52* Solventborne gloss 




D82 1 st HDF Polythane D53* Solventborne gloss 

2 nd Polythane Solventborne gloss 

3 rd Polythane Solventborne gloss 

4 th Polythane Solventborne gloss 

* For particle and fibreboard, replace with one coat of Resene Particle Board Sealer 



3 rd Polysatin D52 Solventborne satin 

4 th Polysatin D52 Solventborne satin 




(Optional) 


3 rd Polysatin Solventborne satin 

4 th Polysatin Solventborne satin 



2 nd Polyflat D52* Solventborne flat 

3 rd Polyflat D52 Solventborne flat 

4 th Polyflat D52 Solventborne flat 


D82 1st CF Waterborne Colorwood 


(Optional) 

2 nd Polyflat D52* Solventborne flat 




2i INTERIOR TIMBER FLOORS, STAINS AND CLEAR FINISHES 

DEDICATED SECTION FOR FLOORS 


Spec. No. 

2i 3.1 F D82 1 st SF Waterborne Colorwood D50a 





D82 1 st CF Aquaclear D59 Waterborne gloss 





Spec. No. 



2i 3.2 F D82 1 st SF Waterborne Colorwood D50 





1 st CF Aquaclear D59 Waterborne semi-gloss 




2i 3.3 F D82 1 st SF Waterborne Colorwood D50 





1 st CF Aquaclear D59 Waterborne satin 




2i 4.1 F D82 1 st HDF Polythane D53* Solventborne gloss 




* For particle and fibre board, replace with one coat of Resene Particle Board Sealer 

2i 4.3 F D82 1 st SF Waterborne Colorwood D50a 

2 nd HD Polysatin D52* Solventborne satin 

3 rd HD Polysatin D52 Solventborne satin 

4 th HD Polysatin D52 Solventborne satin 


* For particle and fibre board, replace with one coat of Resene Aquaclear 

1 st CF HD Polysatin D52* Solventborne satin 

2 nd HD Polysatin D52 Solventborne satin 

3 rd HD Polysatin D52 Solventborne satin 


* For particle and fibre board, replace with one coat of Resene Aquaclear 

3i INTERIOR TIMBER JOINERY 


Spec. No. 


















2 nd Zylone SpaceCote D311 Waterborne low-sheen 



3 Zylone SpaceCote D311 Waterborne low-sheen 




Spec. No. 


TimberLock POV Smooth Surface Sealer D47 





D48 2 nd Lusta-Glo D33 Solventborne semi-gloss 






D48 2 nd Flatcote D306 Solventborne flat 









D82 1 st CF Waterborne Colorwood D50 


(Optional) 












(Optional) 












(Optional) 






2 nd Polyflat D52 





(Optional) 




D82 1 st HDF Polythane D53* Solventborne gloss 




Spec. No. 



* For particle and fibre board, replace with one coat of Resene Particle Board Sealer 







(Optional) 




D82 1 st PBO Aquaclear D59 

2 nd Polysatin D52 Solventborne satin 




2 nd Polyflat D52 Solventborne flat 





(Optional) 




D82 1 st PBO Aquaclear D59 




6i INTERIOR FERROUS METALS 


Spec. No. 









6i 2.1 D801 1 st NRS Rust Arrest RA30 



4 th Super Gloss D32 (Optional) 

1 st HDS Vinyl Etch RA31 



6i 2.2 D801 1 st NRS Rust Arrest RA30 



4 th Lusta-Glo D33 (Optional) 

1 st HDS Vinyl Etch RA31 






Spec. No. 




4 th Flatcote D306 (Optional) 

7i INTERIOR NON-FERROUS METALS 


Spec. No. 









7i 2.1 D89 1 st Vinyl Etch RA31 

2 nd Enamel Undercoat D44 


4 th Super Gloss D32 (Optional) 




4 th Lusta-Glo D33 (Optional) 




4 th Flatcote D306 (Optional) 

9i INTERIOR TOTARA AND MATAI TIMBER ONLY 


Spec. No. 

9i 1.1 D82 & 1 st Quick Dry D45 

TimberLock2 nd Enamacryl D309 Waterborne gloss 

D48 Acrylic Undercoat D404 Waterborne undercoat 



TimberLock2 nd Lustacryl D310 Waterborne semi-gloss 




TimberLock2 nd Zylone SpaceCote D311 Waterborne low-sheen 


3 rd Zylone SpaceCote D311 Waterborne low-sheen 


TimberLock2 nd 


D48 3 rd Super Gloss D32 Solventborne gloss 


TimberLock2 nd Lusta-Glo D33 Solventborne semi-gloss 




TimberLock2 nd Flatcote D306 Solventborne flat 



9i 3.1 D82 1 st Aquaclear D59 Waterborne gloss 





Spec. No. 



9i 3.2 D82 1 st Aquaclear D59 Waterborne semi-gloss 




9i 3.3 D82 1 st Aquaclear D59 Waterborne satin 




9i 4.1 D82 1 st NRS Aquaclear D59 

2 nd Polygloss D52 Solventborne gloss 


4 th Polygloss D52 (Optional) 

1 st HDS Polythane D53 Solventborne gloss 



4 th Polythane D53 (Optional) 

9i 4.3 D82 1 st Aquaclear D59 

2 nd Polysatin D52 Solventborne satin 


4 th Polysatin D52 (Optional) 

9i 4.5 D82 1 st Aquaclear D59 




11i INTERIOR GLASS, GLAZED TILES, FORMICA, POLYETHYLENE, 

POLYPROPYLENE AND BAKED ENAMEL SYSTEMS 


Spec. No. 


or D8032 nd Enamacryl D309 Waterborne gloss 





or D8032 nd Lustacryl D310 Waterborne semi-gloss 





or D8032 nd Lumbersider D34 Waterborne satin 




11i 1.4 ZS D802 1 st Smooth Surface Sealer D47 

or D8032 nd Zylone Sheen D302 Waterborne low sheen 




11i 1.4 SC D802 1 st Smooth Surface Sealer D47 

or D8032 nd Zylone SpaceCote D311 Waterborne low sheen 





or D8032 nd Zylone 20 D37 Waterborne flat 





or D8032 nd 




Spec. No. 




or D8032 nd Lusta-Glo D33 Solventborne semi-gloss 





or D8032 nd Flatcote D306 Solventborne satin 



3 rd Flatcote D306 Solventborne satin 

12i INTERIOR GLASS REINFORCED POLYESTER, GLASS REINFORCED EPOXY, 

PVC, ACRYLIC SHEETING 


Spec. No. 

12i 1.1 D803 1 st Enamacryl D309 Waterborne gloss 




12i 1.2 D803 1 st Lustacryl D310 Waterborne semi-gloss 




12i 1.3 D803 1 st Lumbersider D34 Waterborne satin 




12i 1.4ZS D803 1 st Zylone Sheen D302 Waterborne low sheen 




12i 1.4SC D803 1 st Zylone SpaceCote D311 Waterborne low sheen 




12i 1.5 D803 1 st Zylone 20 D37 Waterborne flat 

















13i INTERIOR BRICK AND TERRACOTTA 


Spec. No. 

13i 1.1 D802 1 st SSP Enamacryl D309 Waterborne gloss 




1 st PCS Sureseal D42 





13i 1.2 D802 1 st SSP Lustacryl D310 Waterborne semi-gloss 



Spec. No. 










13i 1.3 D802 1 st SSP Lumbersider D34 Waterborne satin 









13i 1.4ZS D802 1 st SSP Zylone Sheen D302 Waterborne low sheen 









13i 1.4SC D802 1 st SSP Zylone SpaceCote D311 Waterborne low sheen 




D802 1 st PCS Sureseal D42 





13i 1.5 D802 1 st SSP Zylone 20 D37 Waterborne flat 









13i 2.1 D802 1 st SSP Acrylic Undercoat D404 Waterborne undercoat 

2 nd Super Gloss D32 Solventborne gloss 




13i 2.2 D802 1 st SSP Lusta-Glo D33 Solventborne semi-gloss 









13i 2.5 D802 1 st SSP Flatcote D306 Solventborne flat 










13i INTERIOR BRICK AND TERRACOTTA, CLEAR FINISHES 


Spec. No. 

13e/i 3.1 D802 1 st IO Aquaclear D59 Waterborne gloss 




1 st EI Multishield+ D54a Waterborne gloss 


3 rd Multishield+ D54a Waterborne gloss 

13i 3.2 D802 SE Aquapel D65 

1 st Aquaclear D59 Waterborne semi-gloss 




1 st Multishield+ D54a Waterborne satin 

2 nd Multishield+ D54a Waterborne satin 

3 rd Multishield+ D54a Waterborne satin 


1 st Aquaclear D59 Waterborne satin 



13i 3.5 D802 1 st Multishield+ D54a Waterborne flat 

2 nd Multishield+ D54a Waterborne flat 

3 rd Multishield+ D54a Waterborne flat 


1 st NRS F.10 Glaze D56 Solventborne gloss 




1 st HDS Uracryl 403 RA56 Solventborne gloss 




1 st HDS Uracryl 402 RA55 Solventborne semi-gloss 






14i INTERIOR CLEAR FINISHES ON CLAY TILES, ABSORBENT TILES, STONE AND 

SLATE, DECORATIVE AGGREGATE FLOORING 


Spec. No. 


1 st Aquaclear D59 Waterborne gloss 




1 st Aquaclear D59 Waterborne semi-gloss 




1 st Aquaclear D59 Waterborne satin 





Spec. No. 



1 st LDF F.10 Glaze D56 Solventborne gloss 




1 st HDF Uracryl 403 RA56 Solventborne gloss 




1 st IMC Polythane D53 Solventborne gloss 


3 rd Polythane D53 


1 st HDF Uracryl 402 RA55 Solventborne semi-gloss 



15i INTERIOR PAPER FACED PLASTER/SOLID PLASTER/FIBROUS PLASTER 


Spec. No. 

15i 1.1 L5 D84 1 st NRS Broadwall Acrylic Wallboard Sealer D403 

D85 WSP Sureseal D42 
































15i 1.4 ZS L5 D84 1 st NRS Broadwall Acrylic Wallboard Sealer D403 


D87 2 nd Zylone Sheen D302 Waterborne low sheen 



15i 1.4 ZS L4 D84 1 st NRS Broadwall Acrylic Wallboard Sealer D403 




Spec. No. 


D87 2 nd Zylone Sheen D302 Waterborne low sheen 




15i 1.4 SC L5 D84 1 st NRS Broadwall Acrylic Wallboard Sealer D403 


D87 2 nd Zylone SpaceCote D311 Waterborne low sheen 



15i 1.4 SC L4 D84 1 st NRS Broadwall Acrylic Wallboard Sealer D403 


D87 2 nd Zylone SpaceCote D311 Waterborne low sheen 






D87 2 nd Zylone 20 D37 Waterborne flat 



D84 1 st NRS Broadwall D403 (Ceilings only) 


D87 2 nd Ceiling Paint D305 Waterborne flat 


3 rd Ceiling Paint D305 Waterborne flat 



D87 2 nd Zylone 20 D37 Waterborne flat 




D84 1 st NRS Broadwall D403 (Ceilings only) 


D87 2 nd Ceiling Paint D305 Waterborne flat 



3 rd Ceiling Paint D305 Waterborne flat 

15i 1.5 TF D84 1 st NRS Broadwall Acrylic Wallboard Sealer D403 


D87 2 nd Lumbersider D34 

D807 3 rd Sandtex D71 Waterborne texture 

15i 2.1 L5 

D84 1 st Sureseal D42 

D85 



15i 2.1 L4 D84 1 st Sureseal D42 






D807 3 rd Lusta-Glo D33 Solventborne semi-gloss 








D807 3 rd Flatcote D306 Solventborne flat 



Spec. No. 


15i 2.5 L4 D84 1st Sureseal D42 




16i CANVAS, SCANDATEX AND HESSIAN 


Spec. No. 

16i 1.1 D803 1 st NRS Enamacryl D309 Waterborne gloss 








16i 1.2 D803 1 st NRS Lustacryl D310 Waterborne semi-gloss 








16i 1.3 D803 1 st NRS Lumbersider D34 Waterborne satin 








16i 1.4ZS D803 1 st NRS Zylone Sheen D302 Waterborne low sheen 








16i 1.4SC D803 1 st NRS Zylone SpaceCote D311 Waterborne low sheen 








16i 1.5 D803 1 st NRS Zylone 20 D37 Waterborne flat 








16i 3.1 D803 1 st NRS Aquaclear D59 Waterborne gloss 


1 st WS Multishield+ D54a Waterborne gloss 




Spec. No. 


16i 3.2 D803 1 st NRS Aquaclear D59 Waterborne semi-gloss 


16i 3.3 D84 1 st NRS Aquaclear D59 Waterborne satin 


D84 1 st WS Multishield+ D54a Waterborne satin 

2 nd Multishield+ D54a Waterborne satin 

16i 3.5 D84 1 st WS Multishield+ D54a Waterborne flat 

2 nd Multishield+ D54a Waterborne flat 

18i SPECIALIST FLOOR SYSTEMS 


Spec. No. 

18i 1.1 D83 1 st CS Aquapoxy RA43 Waterborne gloss 

2 nd Aquapoxy RA43* Waterborne gloss 

3 rd Aquapoxy RA43 Waterborne gloss 


18eli 2.1 U D83 1 st CS Armourcote 510 RA40* 



18eli 2.2 D83 1 st CS Armourcote 510 RA40* 



18i 2.2 D83 1 st TS Wood Primer D40 

CS Sidewalk D38 


MPS Quick Dry D45 

2 nd Sidewalk D38* Solventborne semi-gloss 

3 rd Sidewalk D38 Solventborne semi-gloss 


19i ANTI GRAFFITI SYSTEMS 


Spec. No. 

19i 2.1 CA D83 1 st Armourcote 510 RA47 




19i 4.1 CA D83 1 st Uracryl 403 RA56 Clear 

2 nd Uracryl 403 RA56 Clear 

3 rd Uracryl 403 RA56 Clear 

19i 1.1 CA D83 1 st WBS Aquapoxy RA42 Pigmented 



19i 2.1 OA 1 st Smooth Surface Sealer D47 Pigmented 




19i 1.1 OA 1 st WBS Aquapoxy RA42 Pigmented 



19i 1.1 AA 1 st WBS Aquapoxy RA42 Pigmented 



19i 4.1 SA 1 st Uracryl 403 RA56 System Upgrade - Clear 



Spec. No. 


19i 4.1 SS 1 st Imperite 390 RA57 System Upgrade - Clear 

20i TEXTURED COATINGS 


Spec. No. 

20e/i 1.3 P D83 TP Limelock D809 



CB Refer Rockcote Systems Waterborne mid texture 

2 nd Plastercote D72* Waterborne mid texture 

3 rd Plastercote D72 Waterborne mid texture 


* This coat of Resene Plastercote can be replaced by one coat of Resene Sandtex if desired. 

Some applicators may find it easier to apply. 






* For additional waterproofing replace this coat with one coat of Resene X-200; for a higher DFT , 


D83/ 1 st SP Lumbersider D34 

D84 2 nd Sandtex D71 Waterborne fine texture 


21i PAINT EFFECTS 


Spec. No. 



EWM X-200 x 2 D62 


3 rd Paint Effects Medium D307 Waterborne flat - 

colourwashing 

21eli 1.5 R 1 st IO Zylone Sheen x 2 D302 


EWM X-200 x 2 D62 


3 rd Paint Effects Medium D307 Waterborne flat - ragging 

21eli 1.5 S 1 st IO Zylone Sheen x 2 D302 


EWM X-200 x 2 D62 


3 rd Paint Effects Medium D307 Waterborne flat - sponging 

21eli 1.5 L 1 st IO Zylone Sheen x 2 D302 


EWM X-200 x 2 D62 


3 rd Paint Effects Medium D307 Waterborne flat - limewash 

effect 

21i 2.5 C 1 st Lusta-Glo D33 

2 nd Lusta-Glo D33 

3 rd Scumbling Glaze D308 Solventborne flat - 

colourwashing 

21i 2.5 R 1 st Lusta-Glo D33 


3 rd Scumbling Glaze D308 Solventborne flat - ragging 

21i 2.5 S 1 st Lusta-Glo D33 



Spec. No. 



3 rd Scumbling Glaze D308 Solventborne flat - sponging 

21i 2.5 L 1 st Lusta-Glo D33 


3 rd Scumbling Glaze D308 Solventborne flat - 

limewash effect 

22i INTERIOR MILD STEELS 


Spec. No. 

22i 2.1 AF D801.1 1 st Armourcote 210 RA35 Alkyd primer 

D801.8 

D801.5 

or 

D801.7 

2 nd Armourcote 608 RA72 Alkyd gloss 

22i 2.1 UF D801.1 

D801.8 

D801.5 

or 

D801.7 

22i 2.2 UF D801.1 

D801.8 

D801.5 

or 

D801.7 

22i 2.3 AEMF D801.1 

D801.8 

D801.5 

or 

D801.7 

22i 2.4 UF D801.1 

D801.8 

D801.5 

or 

D801.7 

22i 2.5 AMF D801.1 

D801.8 

D801.5 

or 

D801.7 

1 st Armourcote 220 RA34 Epoxy primer 

2 nd Uracryl 403 RA56 Acrylic urethane gloss 



2 nd Uracryl 402 RA55 Acrylic urethane semi-gloss 



2 nd Imperite IF 503 Metallic RA81 Acrylic epoxy satin metallic 

3 rd Imperite IF 502 Clear RA82 


2 nd Uracryl 404 RA59 Acrylic urethane low sheen 



2 nd Micabond RA71 Acrylic urethane metallic 

3 rd Micabond RA71 Acrylic urethane metallic 

25i INTERIOR METALLIC FINISHES 


Spec. No. 

Waterborne metallic finish on Anaglypta, Scandatex, etc 


D85 






Spec. No. 



Waterborne metallic finish on Paperfaced Plasterboard 


D85 





Waterborne metallic finish on MDF joinery/doors 

25i 1.3/52 D82 1 st Quick Dry D45 





Waterborne pearlescent finish on Interior surfaces 

25i 1.3/52P D82 1 st Quick Dry D45 

(MDF) 

D84/ 2 nd Lumbersider D34 Waterborne satin 


(Gib) 4 th Pearl Shimmer D312 Waterborne pearlescent 


Solventborne metallic finish on concrete floor 

25i 2.3/5 D83 1 st Armourcote 510 RA40 


3 rd Uracryl 400 Series Clear 

Solventborne metallic finish on MDF joinery/doors 

25i 2.3/51 D83 1 st Ultrafill 645 


3 rd Imperite IF 502 Clear RA82 

KEY 

ANS Air Dried Stopping and Non Staining Surfaces in Dry Areas 

BS Bituminous Surface 

CF Clear Finish 

CO Ceiling Only 

CS Cementitious Surface 

EI 

Exterior/Interior 

EO Exterior Only 

ES Eroded Surface 

EWM Exterior Waterproofing Membrane 

GCS Glossy Cementitious Surface 

HDS Heavy Duty System 

HO Hardboard Only 

IMC Interior Only Moisture Cure 

IO 

Interior Only 

KS Kwila Coloured Stain 

L4 Level 4 

L5 Level 5 

LDF Light Duty Finish 

MC Moisture Cure 

MPB Matai and Particle Board 

NC New Cedar 

NRS Normal Recommended System 

NSF Non Skid Finish 


NW 

P 

PBO 

PCS 

POV 

PS 

R 

RM 

RPL 

SCS 

SF 

SG 

SOA 

SP 

SS 

SSP 

ST 

TF 

TP 

TS 

TTS 

WBF 

WC 

WNW 

WSP 

New Work 

Powdery 

Particle Board Only 

Plaster Contaminated Surface 

Painting Over Varnish 

Penetrating System 

Repaint 

Risk of Mould 

Resene Paints Limited 

Sound Cementitious Surfaces 

Stained Finish 

Smooth/Glossy Surface 

State of the Art 

Self Primer 

Solvent System 

Sound Surface for Painting 

Solventborne Topcoat 

Textured Finish 

Thin Plaster 

Timber Surface 

Timber That Stains 

Water Based Finish 

Weathered Cedar 

Waterborne, New Work 

Wet, Stained, Porous or Powdery Areas

Resene Paints Masterspec Standard Specification

Create successful ePaper yourself

Delete template?

Save as template?