Chemical Hygiene Plan - Queensborough Community College ...
Chemical Hygiene Plan - Queensborough Community College ... Chemical Hygiene Plan - Queensborough Community College ...
• When PPE must be worn. • What PPE is necessary to carry out a procedure or experiment. • How to properly don, doff, adjust, and wear PPE. • The proper cleaning, care, maintenance, useful life, limitations, and disposal of the PPE. As with any training sessions, PPE training must be documented, including a description of the information covered during the training session and a copy of the sign-in sheet. Training records must be kept of the names of the persons trained, the type of training provided, and the dates when training occurred. Your EHSO will maintain records of employees who attend training sessions. Information on the specific PPE required to carry out procedures within the laboratory using hazardous chemicals must also be included in the laboratory’s Standard Operating Procedures. Your EHS Office can provide information, training, and assistance with conducting hazard assessments and the selection and use of proper PPE. It is the responsibility of the P.I. or laboratory supervisor to ensure laboratory staff have received the appropriate training on the selection and use of proper PPE, that proper PPE is available and in good condition, and that laboratory personnel use proper PPE when working in laboratories under their supervision. 11.3 Eye Protection Eye protection is one of the most important and easiest forms of PPE to wear. Laboratory personnel should use eye protection for many of the chemical and physical hazards found in laboratories including flying particles, broken glass, molten metal, acids or caustic liquids, chemical liquids, chemical gases or vapors, or potentially injurious light radiation. P.I.s and laboratory supervisors are strongly encouraged to make use of eye protection a mandatory requirement for all laboratory personnel, including visitors, working in or entering laboratories under their control. All laboratory employees and visitors should wear protective eyewear while in laboratories where chemicals are being handled or stored, even when not working directly with chemicals. Additional information can be found on the OSHA Health and Safety Topics Page for eye and face protection. 11.4 Eye Protection Selection All protective eye and face devices must comply with ANSI Z87.1-2003, "American National Standard Practice for Occupational and Educational Eye and Face Protection" and be marked to identify the manufacturer. When choosing proper eye protection, be aware there are a number of different styles of eyewear that serve different functions. 79
Prescription Safety Eyewear OSHA regulations require that employees who wear prescription lenses while engaged in operations that involve eye hazards shall wear eye protection that incorporates the prescription in its design, or must wear eye protection that can be worn over the prescription lenses (goggles, face shields, etc.) without disturbing the proper position of the prescription lenses or the protective lenses. Any prescription eyewear purchase must comply with ANSI Z87.1-1989. Please Note: Contact lenses by themselves are not considered to be protective eyewear. Safety Glasses Safety glasses provide eye protection from moderate impact and particles associated with grinding, sawing, scaling, broken glass, and minor chemical splashes, etc. Side protectors are required when there is a hazard from flying objects. Safety glasses are available in prescription form for those persons needing corrective lenses. Safety glasses do not provide adequate protection for processes that involve heavy chemical use such as stirring, pouring, or mixing. In these instances, splash goggles should be used. Splash Goggles Splash goggles provide adequate eye protection from many hazards, including potential chemical splash hazards, use of concentrated corrosive material, and bulk chemical transfer. Goggles are available with clear or tinted lenses, fog proofing, and vented or non-vented frames. Be aware that goggles designed for woodworking are not appropriate for working with chemicals. These types of goggles can be identified by the numerous small holes throughout the facepiece. In the event of a splash, chemicals could enter into the small holes, and result in a chemical exposure to the face. Ensure that the goggles you choose are rated for use with chemicals. Welder’s/Chippers’ Goggles Welder’s goggles provide protection from sparking, scaling, or splashing metals and harmful light rays. Lenses are impact resistant and are available in graduated lens shades. Goggles used for chipping and grinding provide protection from flying particles. A dual protective eyecup houses impact resistant clear lenses with individual cover plates. Face Shields Face shields provide additional protection to the eyes and face when used in combination with safety glasses or splash goggles. Face shields consist of an adjustable headgear and face shield of tinted or clear lenses or a mesh wire screen. They should be used in operations when the entire face needs protection and should be worn to protect the eyes and face from flying particles, metal sparks, and chemical/biological splashes. Face shields with a mesh wire screen are not appropriate for use with chemicals. Face shields are not intended to be used alone and are not a substitute for appropriate eyewear. It is recommended that face shields always be worn in conjunction with a primary form of eye protection such as safety glasses or goggles. 80
- Page 29 and 30: 5.10 Toxic Effects Toxic effects ar
- Page 31 and 32: • All chemical containers MUST be
- Page 33 and 34: · Peroxidizable materials (aldehyd
- Page 35 and 36: 6.4 Transporting Chemicals When tra
- Page 37 and 38: liquids not in use should be kept i
- Page 39 and 40: 7. An inside storage room meeting a
- Page 41 and 42: VII. CHEMICAL HAZARDS Chemicals can
- Page 43 and 44: • Metal Picrate Salts • 2,4-Din
- Page 45 and 46: 7.5 Dangerous When Wet “Dangerous
- Page 47 and 48: ways to remove them if discovered.
- Page 49 and 50: 1(800) 222-1222. If possible, bring
- Page 51 and 52: • Prior approval - Before anyone
- Page 53 and 54: everyone in the laboratory is aware
- Page 55 and 56: particularly hazardous substances
- Page 57 and 58: 8.7 Reproductive Toxins The OSHA La
- Page 59 and 60: 9.1 Chemical Fume Hoods Fume hoods
- Page 61 and 62: inspected, and initials of the insp
- Page 63 and 64: 9.4 Biological Safety Cabinet Certi
- Page 65 and 66: • Plan and prepare for your work
- Page 67 and 68: The topic of glove boxes can be con
- Page 69 and 70: 10.1 Standard Operating Procedures
- Page 71 and 72: paper, boxes, plastics, etc.) withi
- Page 73 and 74: 10.6 Working Alone In Appendix A of
- Page 75 and 76: • The nature of the experiment in
- Page 77 and 78: Additionally, as with installation
- Page 79: • Record keeping requirements •
- Page 83 and 84: different glove types. Different ma
- Page 85 and 86: • Natural Rubber Latex*** - Resis
- Page 87 and 88: The use of all types of respiratory
- Page 89 and 90: your College’s Emergency Procedur
- Page 91 and 92: • Check all pressure, temperature
- Page 93 and 94: If you have been trained and it is
- Page 95 and 96: 4) Try to prevent spilled chemicals
- Page 97 and 98: their use. Colleges and departments
- Page 99 and 100: Once outside, notify emergency resp
- Page 101 and 102: 5) Keep flushing for at least 15 mi
- Page 103 and 104: 3. The New York City Rules and Regu
- Page 105 and 106: 6. Selection of Hazardous Waste Con
- Page 107 and 108: XV. PESTICIDES A pesticide is defin
- Page 109 and 110: 16.1 Institutional Biosafety Commit
- Page 111 and 112: the College’s IACUC must ensure t
- Page 113 and 114: • Materials derived from animals
- Page 115 and 116: the same regulations and laws; and
- Page 117 and 118: problems and compliance issues, and
- Page 119 and 120: from any given amperage, the table
- Page 121 and 122: extension cords, see the Consumer P
- Page 123 and 124: "reset" buttons. They are found on
- Page 125 and 126: properly replaced before use. Movin
- Page 127 and 128: 22.4.1 Handling Compressed Gas Cyli
- Page 129 and 130: materials for connections; toxic an
• When PPE must be worn.<br />
• What PPE is necessary to carry out a procedure or experiment.<br />
• How to properly don, doff, adjust, and wear PPE.<br />
• The proper cleaning, care, maintenance, useful life, limitations, and disposal of the<br />
PPE.<br />
As with any training sessions, PPE training must be documented, including a description of the<br />
information covered during the training session and a copy of the sign-in sheet. Training records<br />
must be kept of the names of the persons trained, the type of training provided, and the dates<br />
when training occurred. Your EHSO will maintain records of employees who attend training<br />
sessions. Information on the specific PPE required to carry out procedures within the laboratory<br />
using hazardous chemicals must also be included in the laboratory’s Standard Operating<br />
Procedures. Your EHS Office can provide information, training, and assistance with conducting<br />
hazard assessments and the selection and use of proper PPE.<br />
It is the responsibility of the P.I. or laboratory supervisor to ensure laboratory staff have<br />
received the appropriate training on the selection and use of proper PPE, that proper PPE is<br />
available and in good condition, and that laboratory personnel use proper PPE when working<br />
in laboratories under their supervision.<br />
11.3 Eye Protection<br />
Eye protection is one of the most important and easiest forms of PPE to wear. Laboratory<br />
personnel should use eye protection for many of the chemical and physical hazards found in<br />
laboratories including flying particles, broken glass, molten metal, acids or caustic liquids,<br />
chemical liquids, chemical gases or vapors, or potentially injurious light radiation.<br />
P.I.s and laboratory supervisors are strongly encouraged to make use of eye protection a<br />
mandatory requirement for all laboratory personnel, including visitors, working in or<br />
entering laboratories under their control.<br />
All laboratory employees and visitors should wear protective eyewear while in laboratories<br />
where chemicals are being handled or stored, even when not working directly with chemicals.<br />
Additional information can be found on the OSHA Health and Safety Topics Page for eye and<br />
face protection.<br />
11.4 Eye Protection Selection<br />
All protective eye and face devices must comply with ANSI Z87.1-2003, "American National<br />
Standard Practice for Occupational and Educational Eye and Face Protection" and be marked to<br />
identify the manufacturer. When choosing proper eye protection, be aware there are a number of<br />
different styles of eyewear that serve different functions.<br />
79