Event V3 Operating Manual - Jands

More documents

Recommendations

Info

Getting Started 5.30 Labelling a Patch ☞ Diagram 5C + 5B The label field is used to name a Patch. An eight character label can be typed using the flash buttons for characters and the function keypad for numbers. 7 8 9 _ ___ P ch1 A 1 PRESET FLASH OR 7 8 9 MEMORY EDIT CHASE 4 5 6 PAGE ASSIGN FILE 1 2 3 BUILD CLEAR STACK 0 ASSIGN FLASH EXIT SETUP RECORD OR MEMORY 4 5 BUILD EXIT Press Exit If only entering a label 0 x x x x x x x x EDIT PAGE ASSIGN FILE 1 2 3 CLEAR SETUP 6 CHASE STACK RECORD ▼ 5C Labelling a Patch 22 Event V3 Manual
© Jands Electronics July 1995 6.00 Manual Controls 6.10 The Presets ☞ Diagram 6A The Preset faders are used to set up lighting levels during a show and while programming Memories and Chases. It is possible to run a show entirely on the presets but generally these controls are used for recording or to make impromptu changes to the stage lighting. 6.20 Preset Faders Diagram 6A, 6B, 6C ☞ ▼ 6A Preset faders ▼ 6B Preset master ▼ 6C Grand master There are two rows of Presets faders on the Event. The top row of faders is Preset 1 and the bottom row is Preset 2. These faders can be used to smoothly fade a light to the desired level. The output level produced by the Preset faders is dependent on the level of the P1 (or P2) Master and the Grand Master fader. Example: • Bring the Grand Master and P1 Master faders to 10 (100%). • Move the Channel 1 Preset fader to 100% and you should see the lights connected to that channel fade up to full level. • Now fade up Channel 2 to 5 (50%). Check that the lights connected to Channel 2 are at about 50% level. • Finally fade the P1 Master down and up to see how it scales the Channel Preset faders. 6.30 Flash Buttons Diagram 6D, 6E ☞ Flash buttons are located below each Channel and Assign master fader. They perform three functions: * Flash: The buttons are used to momentarily flash a channel to the level set by the Add/Solo Master fader. The type of operation of the Flash button depends on the setting of the Add / Solo Master switch. ▼ 6D Flash buttons ▼ 6E Add/Solo switch * Inhibit: To prevent a channel from appearing in any output, hold the Flash button down and press the DBO button. Repeat this procedure to cancel inhibit. When a channel is inhibited, the channel LED and DBO LED flash together. * Text: When a menu is opened and with the cursor in the Label field, the Flash buttons are used to type various characters as marked on the front panel. Event V3 Manual 23
Page 1 and 2: JANDS EVENT © Jands Electronics Ma
Page 3 and 4: Table of Contents © Jands Electron
Page 5 and 6: © Jands Electronics May 1995 - Cha
Page 7 and 8: © Jands Electronics May 1995 23.00
Page 9 and 10: © Jands Electronics July 1995 Gene
Page 11 and 12: © Jands Electronics July 1995 2.00
Page 13 and 14: © Jands Electronics July 1995 7 8
Page 15 and 16: © Jands Electronics July 1995 Gett
Page 19 and 20: © Jands Electronics July 1995 END
Page 21: © Jands Electronics July 1995 S ET
Page 25 and 26: © Jands Electronics July 1995 Crea
Page 27 and 28: © Jands Electronics July 1995 [STA
Page 37 and 38: © Jands Electronics July 1995 END
Page 55 and 56: © Jands Electronics July 1995 Mana
Page 57 and 58: Managing Memories & Chases © Jands
Page 73 and 74:
© Jands Electronics July 1995 [STA
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
© Jands Electronics July 1995 STAR
Page 85 and 86:
© Jands Electronics July 1995 Cont
Page 87 and 88:
© Jands Electronics July 1995 * So
Page 89 and 90:
© Jands Electronics July 1995 1S T
Page 91 and 92:
© Jands Electronics July 1995 2. T
Page 93 and 94:
Page 95 and 96:
© Jands Electronics July 1995 14.0
Page 97 and 98:
Page 99 and 100:
© Jands Electronics July 1995 14.4
Page 101 and 102:
© Jands Electronics May 1995 Advan
Page 103 and 104:
© Jands Electronics May 1995 15.20
Page 106 and 107:
Advanced Features 15.50 Edit Page 1
Page 108 and 109:
Advanced Features Example 1: When s
Page 110 and 111:
Advanced Features 16.00 Restricting
Page 112 and 113:
Advanced Features 17.10To Record a
Page 114 and 115:
Advanced Features 18.00 Advanced Ch
Page 116 and 117:
Advanced Features 18.20 Setting Cha
Page 118 and 119:
Advanced Features 18.30 Setting Cha
Page 120 and 121:
Advanced Features 19.00 Advanced De
Page 122 and 123:
Advanced Features 19.20 Changing th
Page 124 and 125:
Advanced Features 21.00 Clearing Me
Page 126 and 127:
Advanced Features 21.20 Clearing a
Page 128 and 129:
Advanced Features 21.40 Clearing a
Page 130 and 131:
Advanced Features 22.00 Copying Mem
Page 132 and 133:
Advanced Features 22.20 Copying a C
Page 134 and 135:
Advanced Features 22.30 Copying a P
Page 136 and 137:
Advanced Features 23.00 Resetting t
Page 138 and 139:
Advanced Features 24.00 Connecting
Page 140 and 141:
Advanced Features 26.00 Setting the
Page 142 and 143:
Advanced Features 28.00 Connecting
Page 144 and 145:
Advanced Features 30. 00 Floppy Dis
Page 146 and 147:
General 31.00 Maintenance With care
Page 148 and 149:
General 33.00 Battery Replacement T
Page 150 and 151:
Appendix A A EVENT Setup Menu Struc
Page 152 and 153:
Appendix B B Pin Assignments DMX Di
show all

Event V3 Operating Manual - Jands

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?