Peterbilt Model 320 Operator's Manual after 8-07 - Peterbilt Motors ...
Peterbilt Model 320 Operator's Manual after 8-07 - Peterbilt Motors ... Peterbilt Model 320 Operator's Manual after 8-07 - Peterbilt Motors ...
Preventive Maintenance Schedule PART 8: MAINTENANCE AND SERVICE SYSTEM COMPONENT MAINTENANCE TASK Recommended PM Interval I A B C D E Disc Brakes (Bendix) Brake pads Inspect; replace as required. X Brake disc/rotor Inspect for visible cracks, heat checking, galling, or scoring of surface. Check thickness minimum of 1.46” (37 mm). X Caliper sliding function Caliper function Ensure caliper slides freely with no obstructions or excessive play (see manufacturer’s service literature for “Checking Running Clearance”). Inspect bearings, seals, tappet and boots of the guide pins for damage or cracking. X X Adjuster Check operation; inspect as per manufacturer’s service literature. X – 120 – Y53-6015 R(08/07)
PART 8: MAINTENANCE AND SERVICE Preventive Maintenance Schedule SYSTEM COMPONENT MAINTENANCE TASK Recommended PM Interval I A B C D E Hub, Drum, & Hubcap Hubs (non-LMS) Meritor Unitized Wheel End Check the bearing endplay and adjust as required (see "Wheel Bearing Adjustment"). X Hubs (non-LMS) with outrunner seals Clean the components and check for excessive wear or damage. Change the oil and seal (see "Wheel Bearing Lubrication"). X Hubs (non-LMS) with standard seals Clean the components and check for excessive wear or damage. Change the oil and seal (see "Wheel Bearing Lubrication"). X Hub seals (all) Check for leaks; replace as required. X LMS Hubs (Dana) LMS Hubs (Dana) with Synthetic Lubricant LMS Hubs (Dana) with Mineral Lubricant Brake drums Hubcaps Check the bearing endplay and adjust as required (see "Wheel Bearing Adjustment"). Clean the components and check for excessive wear or damage. Change the oil and seal (see "Wheel Bearing Adjustment"). Clean the components and check for excessive wear or damage. Change the oil and seal (see "Wheel Bearing Adjustment"). Inspect for visible cracks, heat checking, galling or scoring of the braking surface, and for severe corrosion on the outside surface. Check for out-of-round or oversize condition [0.080 in. (2 mm) more than the original diameter]. Replace as required. Clean the sight window. Check the center plug, mounting flange, and fill plug for leaks and for proper installation. Replace broken or damaged parts. Check the lubricant level and add as required. X 500,000 miles/ 800,000 km 350,000 miles/ 560,000 km X X R(08/07) Y53-6015 – 121 –
- Page 74 and 75: Checking Under the Hood or Cab PART
- Page 76 and 77: After Engine Warmup 17.Check spring
- Page 78 and 79: Engine Warmup If the engine still w
- Page 80 and 81: Transmission Warmup CAUTION: The us
- Page 82 and 83: Shifting Gears in a New Vehicle CAU
- Page 84 and 85: Operating the Clutch service depart
- Page 86 and 87: Dual Range (Two Speed) Axles WARNIN
- Page 88 and 89: Automatic and Automated Transmissio
- Page 90 and 91: If Your Vehicle Must Be Towed PART
- Page 92 and 93: Anti-Lock Braking System Operating
- Page 94 and 95: ABS Warning Lamps PART 7: STARTING
- Page 96 and 97: Overheated Brakes PART 7: STARTING
- Page 98 and 99: Parking Brakes and Their Use PART 7
- Page 100 and 101: Manually Releasing Spring Brakes PA
- Page 102 and 103: Before Stopping The Engine PART 7:
- Page 104 and 105: Setting Ride Height PART 7: STARTIN
- Page 106 and 107: Setting Ride Height PART 7: STARTIN
- Page 108 and 109: Driving Tips And Techniques WARNING
- Page 110 and 111: Dual Steer Vehicle Operation NOTE:
- Page 112 and 113: Dual Steer Vehicle Operation PART 7
- Page 114 and 115: Preventive Maintenance Schedule PAR
- Page 116 and 117: Preventive Maintenance Schedule PAR
- Page 118 and 119: Preventive Maintenance Schedule PAR
- Page 120 and 121: Preventive Maintenance Schedule PAR
- Page 122 and 123: Preventive Maintenance Schedule PAR
- Page 126 and 127: Preventive Maintenance Schedule PAR
- Page 128 and 129: Preventive Maintenance Schedule PAR
- Page 130 and 131: Preventive Maintenance Schedule PAR
- Page 132 and 133: Preventive Maintenance Schedule PAR
- Page 134 and 135: Preventive Maintenance Schedule PAR
- Page 136 and 137: Preventive Maintenance Schedule PAR
- Page 138 and 139: Preventive Maintenance Schedule PAR
- Page 140 and 141: Master Lubrication Index WARNING! E
- Page 142 and 143: Fuller Transmission Lubrication PAR
- Page 144 and 145: Spicer Transmission Lubrication Rec
- Page 146 and 147: Meritor Axle Lubrication PART 8: MA
- Page 148 and 149: Wheel Bearing Lubrication PART 8: M
- Page 150 and 151: Brake Adjustment PART 8: MAINTENANC
- Page 152 and 153: Brake Adjustment PART 8: MAINTENANC
- Page 154 and 155: Tires Checking Inflation Pressure G
- Page 156 and 157: Tires PART 8: MAINTENANCE AND SERVI
- Page 158 and 159: Tires PART 8: MAINTENANCE AND SERVI
- Page 160 and 161: Tires PART 8: MAINTENANCE AND SERVI
- Page 162 and 163: Wheels And Rims Wheels And Rims PAR
- Page 164 and 165: Wheels And Rims PART 8: MAINTENANCE
- Page 166 and 167: Vehicle Loading PART 8: MAINTENANCE
- Page 168 and 169: Air Dryer then goes to the reservoi
- Page 170 and 171: Engine Cooling System Engine Coolin
- Page 172 and 173: Engine Cooling System ELC Extender
Preventive Maintenance Schedule<br />
PART 8: MAINTENANCE AND SERVICE<br />
SYSTEM COMPONENT MAINTENANCE TASK<br />
Recommended PM Interval<br />
I A B C D E<br />
Disc Brakes<br />
(Bendix)<br />
Brake pads Inspect; replace as required. X<br />
Brake disc/rotor<br />
Inspect for visible cracks, heat checking, galling, or scoring of<br />
surface. Check thickness minimum of 1.46” (37 mm).<br />
X<br />
Caliper sliding function<br />
Caliper function<br />
Ensure caliper slides freely with no obstructions or excessive<br />
play (see manufacturer’s service literature for “Checking Running<br />
Clearance”).<br />
Inspect bearings, seals, tappet and boots of the guide pins for<br />
damage or cracking.<br />
X<br />
X<br />
Adjuster Check operation; inspect as per manufacturer’s service literature. X<br />
– 120 – Y53-6015 R(08/<strong>07</strong>)