Peterbilt Model 320 Operator's Manual after 8-07 - Peterbilt Motors ...
Peterbilt Model 320 Operator's Manual after 8-07 - Peterbilt Motors ... Peterbilt Model 320 Operator's Manual after 8-07 - Peterbilt Motors ...
Preventive Maintenance Schedule PART 8: MAINTENANCE AND SERVICE SYSTEM COMPONENT MAINTENANCE TASK Recommended PM Interval I A B C D E Front Axle (Dana) Total Vehicle Alignment Check and adjust as required. X X Kingpin bushings, thrust bearings, & tie rod ball ends (ON HIGHWAY) Check and adjust as required. X Kingpin bushings, thrust bearings, & tie rod ball ends (OFF HIGHWAY AND VOCATIONAL) Lubricate with approved grease. X Steering knuckle spindles, thrust bearings, kingpins, drawkeys, tie rod ends, steering stops, & bushings (ON HIGHWAY) Inspect for wear and damage and for endplay. Shim or replace as required. X Steering knuckle spindles, thrust bearings, kingpins, drawkeys, tie rod ends, steering stops, & bushings (OFF HIGHWAY AND VOCATIONAL) Inspect for wear and damage and for endplay. Shim or replace as required. X – 114 – Y53-6015 R(08/07)
PART 8: MAINTENANCE AND SERVICE Preventive Maintenance Schedule SYSTEM COMPONENT MAINTENANCE TASK Recommended PM Interval I A B C D E Front Suspension Front Spring Inspect for cracked leaves, worn bushings, & excessive corrosion. X Spring Pins & Shackles Inspect for worn parts and excessive joint clearance. Shim or replace as required. X Shock Absorbers Inspect for leaking, body damage, and damaged or worn bushings. Replace as required. Check the shock mounting stud torque. X Check for proper function. X U-bolts (ON HIGHWAY) Check the general condition and the tightness of the nuts. Tighten the nuts to the specified torque value as required (see "U-Bolt Tension for Front and Rear Axles"). X X U-bolts (OFF HIGHWAY) Check the general condition and the tightness of the nuts. Tighten the nuts to the specified torque value as required (see "U-Bolt Tension for Front and Rear Axles"). X R(08/07) Y53-6015 – 115 –
- Page 68 and 69: Tether Belts PART 5: SEAT AND RESTR
- Page 70 and 71: Inspection of the Restraint System
- Page 72 and 73: Inspection of the Restraint System
- Page 74 and 75: Checking Under the Hood or Cab PART
- Page 76 and 77: After Engine Warmup 17.Check spring
- Page 78 and 79: Engine Warmup If the engine still w
- Page 80 and 81: Transmission Warmup CAUTION: The us
- Page 82 and 83: Shifting Gears in a New Vehicle CAU
- Page 84 and 85: Operating the Clutch service depart
- Page 86 and 87: Dual Range (Two Speed) Axles WARNIN
- Page 88 and 89: Automatic and Automated Transmissio
- Page 90 and 91: If Your Vehicle Must Be Towed PART
- Page 92 and 93: Anti-Lock Braking System Operating
- Page 94 and 95: ABS Warning Lamps PART 7: STARTING
- Page 96 and 97: Overheated Brakes PART 7: STARTING
- Page 98 and 99: Parking Brakes and Their Use PART 7
- Page 100 and 101: Manually Releasing Spring Brakes PA
- Page 102 and 103: Before Stopping The Engine PART 7:
- Page 104 and 105: Setting Ride Height PART 7: STARTIN
- Page 106 and 107: Setting Ride Height PART 7: STARTIN
- Page 108 and 109: Driving Tips And Techniques WARNING
- Page 110 and 111: Dual Steer Vehicle Operation NOTE:
- Page 112 and 113: Dual Steer Vehicle Operation PART 7
- Page 114 and 115: Preventive Maintenance Schedule PAR
- Page 116 and 117: Preventive Maintenance Schedule PAR
- Page 120 and 121: Preventive Maintenance Schedule PAR
- Page 122 and 123: Preventive Maintenance Schedule PAR
- Page 124 and 125: Preventive Maintenance Schedule PAR
- Page 126 and 127: Preventive Maintenance Schedule PAR
- Page 128 and 129: Preventive Maintenance Schedule PAR
- Page 130 and 131: Preventive Maintenance Schedule PAR
- Page 132 and 133: Preventive Maintenance Schedule PAR
- Page 134 and 135: Preventive Maintenance Schedule PAR
- Page 136 and 137: Preventive Maintenance Schedule PAR
- Page 138 and 139: Preventive Maintenance Schedule PAR
- Page 140 and 141: Master Lubrication Index WARNING! E
- Page 142 and 143: Fuller Transmission Lubrication PAR
- Page 144 and 145: Spicer Transmission Lubrication Rec
- Page 146 and 147: Meritor Axle Lubrication PART 8: MA
- Page 148 and 149: Wheel Bearing Lubrication PART 8: M
- Page 150 and 151: Brake Adjustment PART 8: MAINTENANC
- Page 152 and 153: Brake Adjustment PART 8: MAINTENANC
- Page 154 and 155: Tires Checking Inflation Pressure G
- Page 156 and 157: Tires PART 8: MAINTENANCE AND SERVI
- Page 158 and 159: Tires PART 8: MAINTENANCE AND SERVI
- Page 160 and 161: Tires PART 8: MAINTENANCE AND SERVI
- Page 162 and 163: Wheels And Rims Wheels And Rims PAR
- Page 164 and 165: Wheels And Rims PART 8: MAINTENANCE
- Page 166 and 167: Vehicle Loading PART 8: MAINTENANCE
PART 8: MAINTENANCE AND SERVICE<br />
Preventive Maintenance Schedule<br />
SYSTEM COMPONENT MAINTENANCE TASK<br />
Recommended PM Interval<br />
I A B C D E<br />
Front<br />
Suspension<br />
Front Spring Inspect for cracked leaves, worn bushings, & excessive corrosion. X<br />
Spring Pins & Shackles<br />
Inspect for worn parts and excessive joint clearance. Shim or<br />
replace as required.<br />
X<br />
Shock Absorbers<br />
Inspect for leaking, body damage, and damaged or worn bushings.<br />
Replace as required. Check the shock mounting stud torque.<br />
X<br />
Check for proper function.<br />
X<br />
U-bolts (ON HIGHWAY)<br />
Check the general condition and the tightness of the nuts. Tighten<br />
the nuts to the specified torque value as required (see "U-Bolt<br />
Tension for Front and Rear Axles").<br />
X<br />
X<br />
U-bolts (OFF HIGHWAY)<br />
Check the general condition and the tightness of the nuts. Tighten<br />
the nuts to the specified torque value as required (see "U-Bolt<br />
Tension for Front and Rear Axles").<br />
X<br />
R(08/<strong>07</strong>) Y53-6015 – 115 –