IntelliTouch Expansion Center Installation Guide - Pentair
IntelliTouch Expansion Center Installation Guide - Pentair
IntelliTouch Expansion Center Installation Guide - Pentair
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
2<br />
<strong>Installation</strong> Steps Summary<br />
Note: Use the following instructions to install and connect additional expansion center enclosures to<br />
existing Load <strong>Center</strong> or Power <strong>Center</strong>. For Load <strong>Center</strong> or Power <strong>Center</strong> installation instructions,<br />
refer to the Load <strong>Center</strong> or Power <strong>Center</strong> <strong>Installation</strong> <strong>Guide</strong> (P/N 520100).<br />
The recommended installation steps for the <strong>Expansion</strong> Kit are as follows:<br />
1<br />
2<br />
3<br />
4<br />
5<br />
Install the Outdoor Control Panel (page 4): Remove the high voltage panel from the<br />
<strong>Expansion</strong> <strong>Center</strong> enclosure and install the Outdoor Control Panel.<br />
Connect Pre-installed Relays (page 5): Connect the relay plugs to the Personality board.<br />
The four relays are pre-installed in the Power/Load <strong>Center</strong>.<br />
Installing Auxiliary Relays (page 6): Install and connect the relay(s). For models i5x and i10x.<br />
Connecting the <strong>Expansion</strong> <strong>Center</strong> to the Load/Power <strong>Center</strong> (page 7): Connect the 4-wire<br />
cable from the Load <strong>Center</strong> or Power <strong>Center</strong> to the COM port on the Personality board in the<br />
<strong>Expansion</strong> <strong>Center</strong> enclosure.<br />
Connecting the <strong>Expansion</strong> <strong>Center</strong> transformer (page 9): Connect the transformer harness<br />
to the Personality board.<br />
6<br />
Affixing the System Wiring Diagram Label (page 9): Affix the wiring diagram on the inside of<br />
the front door of the <strong>Expansion</strong> enclosure (for models i5S, i9+3S, i10+3D only).<br />
<strong>Expansion</strong> <strong>Center</strong> Enclosure Location<br />
All pool equipment including the <strong>Expansion</strong> <strong>Center</strong> enclosure, with the exception of the Spa-Side<br />
remote, must be located at least 10 ft. from the water’s edge.<br />
<strong>Expansion</strong> <strong>Center</strong> Setup Options<br />
An <strong>Expansion</strong> <strong>Center</strong> enclosure can be a Load <strong>Center</strong> or Power <strong>Center</strong> enclosure. Install the<br />
<strong>Expansion</strong> <strong>Center</strong> enclosure’s near to the main Load <strong>Center</strong> or Power <strong>Center</strong>. The <strong>Expansion</strong> <strong>Center</strong><br />
can support all of the same high voltage connections as the main load to the Load <strong>Center</strong> or Power<br />
<strong>Center</strong>. For more information, refer to the Load <strong>Center</strong> and Power <strong>Center</strong> <strong>Installation</strong> <strong>Guide</strong> (P/N<br />
520100). The <strong>Expansion</strong> <strong>Center</strong> enclosure includes COM port connections, and two actuators as<br />
does the Load <strong>Center</strong> or Power <strong>Center</strong>. The <strong>Expansion</strong> <strong>Center</strong> enclosure can be expanded to<br />
include up to five actuators (with valve module P/N 520285).<br />
Main Load <strong>Center</strong><br />
(i9+3, i9+3S, i10+3D)<br />
<strong>Expansion</strong> <strong>Center</strong><br />
(i5x or i10x)<br />
Additional<br />
<strong>Expansion</strong><br />
<strong>Center</strong><br />
Additional<br />
<strong>Expansion</strong> <strong>Center</strong><br />
(3 maximum)<br />
<strong>IntelliTouch</strong> <strong>Expansion</strong> <strong>Center</strong> Kit <strong>Installation</strong> <strong>Guide</strong>
Change language