IntelliTouch Expansion Center Installation Guide - Pentair
IntelliTouch Expansion Center Installation Guide - Pentair
IntelliTouch Expansion Center Installation Guide - Pentair
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
pool/spa control system<br />
<strong>IntelliTouch</strong> ® <strong>Expansion</strong> <strong>Center</strong> Kit<br />
<strong>Installation</strong> <strong>Guide</strong><br />
IMPORTANT SAFETY INSTRUCTIONS<br />
READ AND FOLLOW ALL INSTRUCTIONS<br />
SAVE THESE INSTRUCTIONS
© 2005 <strong>Pentair</strong> Water Pool and Spa, Inc. All rights reserved<br />
This document is subject to change without notice<br />
1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000<br />
10951 West Los Angeles Ave., Moorpark, CA 93021 • (805) 523-2400<br />
Trademarks and disclaimers<br />
<strong>IntelliTouch</strong>, EasyTouch, IntelliChlor, IntelliFlo, QuickTouch, MobileTouch, SAm, SAL, and FIBERworks, and the<br />
<strong>Pentair</strong> Water Pool and Spa logo are trademarks of <strong>Pentair</strong> Water Pool and Spa, Inc. Other trademarks and trade<br />
names may be used in this document to refer to either the entities claiming the marks and names or their products.<br />
<strong>Pentair</strong> Water Pool and Spa, Inc. disclaims proprietary interest in marks and names of others.<br />
P/N 520471 - Rev A - 09/27/05
i<br />
Contents<br />
IMPORTANT SAFETY PRECAUTIONS ............................................................... ii<br />
<strong>IntelliTouch</strong> <strong>Expansion</strong> <strong>Center</strong> Kit Contents ............................................................. 1<br />
About the <strong>Installation</strong> <strong>Guide</strong> ..................................................................................... 1<br />
Related Manuals ...................................................................................................... 1<br />
Technical Support .................................................................................................... 1<br />
<strong>Installation</strong> Steps Summary ..................................................................................... 2<br />
<strong>Expansion</strong> <strong>Center</strong> Enclosure Location .................................................................... 2<br />
<strong>Expansion</strong> <strong>Center</strong> Setup Options ............................................................................ 2<br />
Installing Conduit and Wire ...................................................................................... 3<br />
Installing the Outdoor Control Panel ........................................................................ 4<br />
Connecting the <strong>Expansion</strong> <strong>Center</strong> Pre-Installed Relays .......................................... 5<br />
Installing Auxiliary Relays (Model i5x and i10x) ........................................................ 6<br />
Connecting the <strong>Expansion</strong> <strong>Center</strong> to the Load/Power <strong>Center</strong> ................................. 7<br />
Connecting the <strong>Expansion</strong> <strong>Center</strong> Transformer ...................................................... 9<br />
System Wiring Diagram .......................................................................................... 10<br />
Glossary .................................................................................................................. 11<br />
<strong>IntelliTouch</strong> <strong>Expansion</strong> <strong>Center</strong> Kit <strong>Installation</strong> <strong>Guide</strong>
ii<br />
IMPORTANT SAFETY PRECAUTIONS<br />
Important Notice:<br />
Attention Installer: This manual contains important information about the installation, operation<br />
and safe use of this product. This information should be given to the owner and/or operator of this<br />
equipment.<br />
WARNING - Before installing this product, read and follow all warning notices and instructions<br />
which are included. Failure to follow safety warnings and instructions can result in severe injury,<br />
death, or property damage. Call (800) 831-7133 for additional free copies of these instructions.<br />
WARNING - Water temperature in excess of 100 degrees Fahrenheit may be hazardous to your<br />
health. Prolonged immersion in hot water may induce hyperthermia. Hyperthermia occurs when the<br />
internal temperature of the body reaches a level several degrees above normal body temperature of<br />
98.6° F (37° C). The symptoms of hyperthermia include drowsiness, lethargy, dizziness, fainting,<br />
and an increase in the internal temperature of the body.<br />
The effects of hyperthermia include: 1) Unawareness of impending danger. 2) Failure to perceive<br />
heat. 3) Failure to recognize the need to leave the spa. 4) Physical inability to exit the spa. 5) Fetal<br />
damage in pregnant women. 6) Unconsciousness resulting in danger of drowning.<br />
WARNING - To reduce the risk of injury, do not permit children to use this product unless they<br />
are closely supervised at all times.<br />
WARNING - The use of alcohol, drugs, or medication can greatly increase the risk of fatal<br />
hyperthermia in hot tubs and spas.<br />
WARNING - Control System is intended to control heaters with built-in high limit circuits ONLY.<br />
Failure to do so may cause property damage or personal injury.<br />
WARNING - Do not use this product to control an automatic pool cover. Swimmers may become<br />
entrapped underneath the cover.<br />
WARNING - For units intended for use in other than single-family dwellings, a clearly labeled<br />
emergency switch shall be provided as part of the installation. The switch shall be readily accessible<br />
to the occupants and shall be installed at least 10 feet (3.05 m) away, adjacent to, and within sight of,<br />
the unit.<br />
CAUTION - Except for listed spa-side remote controls, install a minimum of five (5) feet from<br />
the inside wall of the pool and spa.<br />
<strong>IntelliTouch</strong> <strong>Expansion</strong> <strong>Center</strong> Kit <strong>Installation</strong> <strong>Guide</strong>
iii<br />
IMPORTANT SAFETY PRECAUTIONS (Continued)<br />
General <strong>Installation</strong> Information<br />
1. All work must be performed by a licensed electrician, and must conform to all national, state,<br />
and local codes.<br />
2. Install to provide drainage of compartment for electrical components.<br />
3. If this system is used to control underwater lighting fixtures, a ground-fault interrupter<br />
(GFCI) must be provided for these fixtures. Conductors on the load side of the ground-fault<br />
circuit-interrupter shall not occupy conduit, junction boxes or enclosures containing other<br />
conductors unless such conductors are also protected by a ground-fault circuit-interrupter.<br />
Refer to local codes for details.<br />
4. A terminal bar stamped is located inside the supply terminal box. To reduce the risk<br />
of electric shock, this terminal must be connected to the grounding means provided in the<br />
electric supply service panel with a continuous copper wire equivalent in size to the circuit<br />
conductors supplying this equipment (no smaller than 12 AWG or 3.3 mm). The bonding<br />
lug(s) provided on this unit are intended to connect a minimum of one No. 8 AWG for US<br />
installation and two No. 6 AWG for Canadian installations solid copper conductor between<br />
this unit and any metal equipment, metal enclosures or electrical equipment, metal water<br />
pipe, or conduit within 5 feet (1.5 m) of the unit.<br />
5. The electrical supply for this product must include a suitably rated switch or circuit breaker<br />
to open all ungrounded supply conductors to comply with Section 422-20 of the National<br />
Electrical Code, ANSI/NFPA 70.1987. The disconnecting means must be readily<br />
accessible to the tub occupant but installed at least 10 ft. (3.05 m) from the inside wall of<br />
the pool.<br />
6. Supply conductor must be sized to support all loads. Maximum supply conductor current<br />
must be 125 Amps at 125 VAC or 63 Amps at 240 VAC.<br />
<strong>IntelliTouch</strong> <strong>Expansion</strong> <strong>Center</strong> Kit <strong>Installation</strong> <strong>Guide</strong>
iv<br />
<strong>IntelliTouch</strong> <strong>Expansion</strong> <strong>Center</strong> Kit <strong>Installation</strong> <strong>Guide</strong>
1<br />
<strong>IntelliTouch</strong> <strong>Expansion</strong> <strong>Center</strong> Kit Contents<br />
The following items are included in the <strong>Expansion</strong> <strong>Center</strong> kit. If any items are missing please contact<br />
Technical Support.<br />
• <strong>IntelliTouch</strong> <strong>Expansion</strong> <strong>Center</strong><br />
• Outdoor Control Panel. Includes motherboard and Personality board<br />
• Power Relays - Models i5x and i10x (5 relays)<br />
• Wiring Diagram Label - To affix to the inside front door (for models i5x and i10x)<br />
• Label Sheet - A set of adhesive labels for custom identification (for outdoor control panel<br />
buttons). Use a pair of fine-tip tweezers to remove the labels from the sheet<br />
• <strong>IntelliTouch</strong> <strong>Expansion</strong> <strong>Center</strong> Kit <strong>Installation</strong> <strong>Guide</strong> (this manual)<br />
About this <strong>Installation</strong> <strong>Guide</strong><br />
Use the information in this manual to install the <strong>IntelliTouch</strong> <strong>Expansion</strong> <strong>Center</strong> kit contents.<br />
Related Manuals<br />
• For information about configuring an <strong>Expansion</strong> <strong>Center</strong> with the <strong>IntelliTouch</strong> system, refer to<br />
the <strong>IntelliTouch</strong> System User’s <strong>Guide</strong> (P/N 520102)<br />
• For Load <strong>Center</strong> and Power <strong>Center</strong> installation instructions, refer to the Load <strong>Center</strong> and<br />
Power <strong>Center</strong> <strong>Installation</strong> <strong>Guide</strong> (P/N 520100)<br />
• For additional <strong>IntelliTouch</strong> installation information, refer to the <strong>IntelliTouch</strong> Personality Kit<br />
<strong>Installation</strong> <strong>Guide</strong> (P/N 520101) and the <strong>IntelliTouch</strong> System User’s <strong>Guide</strong> (P/N 520101)<br />
Technical Support<br />
Contact Technical Support at:<br />
Sanford, North Carolina (8 A.M. to 5 P.M.)<br />
Phone: (800) 831-7133<br />
Fax: (919) 566-8920<br />
Moorpark, California (8 A.M. to 5 P.M.)<br />
Phone: (800) 831-7133 (Ext. 6502)<br />
Fax: (805) 530-0194<br />
Web sites<br />
visit www.pentairpool.com and www.staritepool.com<br />
<strong>IntelliTouch</strong> <strong>Expansion</strong> <strong>Center</strong> Kit <strong>Installation</strong> <strong>Guide</strong>
2<br />
<strong>Installation</strong> Steps Summary<br />
Note: Use the following instructions to install and connect additional expansion center enclosures to<br />
existing Load <strong>Center</strong> or Power <strong>Center</strong>. For Load <strong>Center</strong> or Power <strong>Center</strong> installation instructions,<br />
refer to the Load <strong>Center</strong> or Power <strong>Center</strong> <strong>Installation</strong> <strong>Guide</strong> (P/N 520100).<br />
The recommended installation steps for the <strong>Expansion</strong> Kit are as follows:<br />
1<br />
2<br />
3<br />
4<br />
5<br />
Install the Outdoor Control Panel (page 4): Remove the high voltage panel from the<br />
<strong>Expansion</strong> <strong>Center</strong> enclosure and install the Outdoor Control Panel.<br />
Connect Pre-installed Relays (page 5): Connect the relay plugs to the Personality board.<br />
The four relays are pre-installed in the Power/Load <strong>Center</strong>.<br />
Installing Auxiliary Relays (page 6): Install and connect the relay(s). For models i5x and i10x.<br />
Connecting the <strong>Expansion</strong> <strong>Center</strong> to the Load/Power <strong>Center</strong> (page 7): Connect the 4-wire<br />
cable from the Load <strong>Center</strong> or Power <strong>Center</strong> to the COM port on the Personality board in the<br />
<strong>Expansion</strong> <strong>Center</strong> enclosure.<br />
Connecting the <strong>Expansion</strong> <strong>Center</strong> transformer (page 9): Connect the transformer harness<br />
to the Personality board.<br />
6<br />
Affixing the System Wiring Diagram Label (page 9): Affix the wiring diagram on the inside of<br />
the front door of the <strong>Expansion</strong> enclosure (for models i5S, i9+3S, i10+3D only).<br />
<strong>Expansion</strong> <strong>Center</strong> Enclosure Location<br />
All pool equipment including the <strong>Expansion</strong> <strong>Center</strong> enclosure, with the exception of the Spa-Side<br />
remote, must be located at least 10 ft. from the water’s edge.<br />
<strong>Expansion</strong> <strong>Center</strong> Setup Options<br />
An <strong>Expansion</strong> <strong>Center</strong> enclosure can be a Load <strong>Center</strong> or Power <strong>Center</strong> enclosure. Install the<br />
<strong>Expansion</strong> <strong>Center</strong> enclosure’s near to the main Load <strong>Center</strong> or Power <strong>Center</strong>. The <strong>Expansion</strong> <strong>Center</strong><br />
can support all of the same high voltage connections as the main load to the Load <strong>Center</strong> or Power<br />
<strong>Center</strong>. For more information, refer to the Load <strong>Center</strong> and Power <strong>Center</strong> <strong>Installation</strong> <strong>Guide</strong> (P/N<br />
520100). The <strong>Expansion</strong> <strong>Center</strong> enclosure includes COM port connections, and two actuators as<br />
does the Load <strong>Center</strong> or Power <strong>Center</strong>. The <strong>Expansion</strong> <strong>Center</strong> enclosure can be expanded to<br />
include up to five actuators (with valve module P/N 520285).<br />
Main Load <strong>Center</strong><br />
(i9+3, i9+3S, i10+3D)<br />
<strong>Expansion</strong> <strong>Center</strong><br />
(i5x or i10x)<br />
Additional<br />
<strong>Expansion</strong><br />
<strong>Center</strong><br />
Additional<br />
<strong>Expansion</strong> <strong>Center</strong><br />
(3 maximum)<br />
<strong>IntelliTouch</strong> <strong>Expansion</strong> <strong>Center</strong> Kit <strong>Installation</strong> <strong>Guide</strong>
3<br />
Installing Conduit and Wire<br />
• Run the appropriate size conduit from the sub-panel to the <strong>Expansion</strong> <strong>Center</strong> (see diagram<br />
below for knockout locations). Run the appropriate conduit and wire from the main Load<br />
<strong>Center</strong> or Power <strong>Center</strong> to the <strong>Expansion</strong> <strong>Center</strong>.<br />
• Run a 4-wire communication cable from the Load <strong>Center</strong> or Power <strong>Center</strong> to the <strong>Expansion</strong><br />
<strong>Center</strong>.<br />
• Supply cable(s) to the Load <strong>Center</strong> or Power <strong>Center</strong> must have a minimum current capacity<br />
suitable for the intended load(s).<br />
• Supply circuit must be protected by suitable breaker rated no higher than 125 AMP.<br />
High voltage<br />
cover panel<br />
attachment<br />
screw holes<br />
Spring latch<br />
Front door<br />
removal screw<br />
GFCI knockout<br />
(approved rainproof<br />
cover required)<br />
Low voltage<br />
raceway<br />
knockout<br />
<strong>Expansion</strong> <strong>Center</strong> Enclosure<br />
<strong>IntelliTouch</strong> <strong>Expansion</strong> <strong>Center</strong> Kit <strong>Installation</strong> <strong>Guide</strong>
4<br />
Installing the Outdoor Control Panel<br />
The <strong>Expansion</strong> <strong>Center</strong> Outdoor Control Panel includes a motherboard and Personality board. The<br />
Personality board is mounted on top of the Motherboard which mounts on the back of the Outdoor<br />
Control Panel. The Outdoor Control Panel installs in the top part of the <strong>Expansion</strong> <strong>Center</strong>.<br />
To install the Outdoor Control Panel in the <strong>Expansion</strong> <strong>Center</strong>:<br />
1. Unlatch the front door spring latches, and open the front door of the <strong>Expansion</strong> <strong>Center</strong>.<br />
2. Remove the cover-panel screws securing the high voltage cover-panel, and remove it from<br />
the enclosure.<br />
3. Mount the Outdoor Control Panel in the top part of the <strong>Expansion</strong> <strong>Center</strong>. Secure it with two<br />
access screws on the bottom edge of control panel. Once secured, the Outdoor Control<br />
Panel can hinge out and down to access the Personality board for low voltage connections.<br />
4. When finished with the relay, and transformer connections (see pages 6 through 9), close<br />
the hinged Outdoor Control Panel and secure it with the two access screws.<br />
5. Install the cover-panel and secure it with the two retaining screws.<br />
6. Close the front door of the <strong>Expansion</strong> <strong>Center</strong>. Fasten the two spring latches.<br />
Outdoor Control Panel<br />
Access screw<br />
Access screw<br />
Cover-panel screw<br />
(Cover-panel not shown)<br />
Cover-panel screw<br />
Retaining screw<br />
Retaining screw<br />
<strong>Expansion</strong> <strong>Center</strong><br />
<strong>IntelliTouch</strong> <strong>Expansion</strong> <strong>Center</strong> Kit <strong>Installation</strong> <strong>Guide</strong>
5<br />
Connecting the <strong>Expansion</strong> <strong>Center</strong> Pre-Installed Relays<br />
There are five pre-installed relays in the <strong>Expansion</strong> <strong>Center</strong>.<br />
To connect the pre-installed relay cable plugs to the Personality board:<br />
• Route the power relay cable plugs up through the high voltage compartment to the<br />
Personality Board. Insert the plug into the two-pin sockets, beginning with AUX1, then<br />
AUX2, AUX3, AUX4, and AUX5. For the two-pin socket locations, refer to the diagram<br />
shown below and the System Wiring Diagrams for models i5x, and i10x.<br />
AUX1, AUX2,<br />
AUX3, AUX4,<br />
AUX5<br />
Personality<br />
Board<br />
Feed each relay<br />
cable plug up<br />
through holes<br />
<strong>IntelliTouch</strong> <strong>Expansion</strong> <strong>Center</strong> Kit <strong>Installation</strong> <strong>Guide</strong>
6<br />
Installing Auxiliary Relays (Model i10x only)<br />
Install additional <strong>Expansion</strong> <strong>Center</strong> axillary relays as needed. There may be as many as five<br />
additional relays.<br />
To install a relay:<br />
1. At the <strong>Expansion</strong> <strong>Center</strong>, install the relays below the pre-installed relays. Secure in place<br />
with two retaining screws.<br />
2. Route the relay cable plug up through the holes into the high voltage compartment to the<br />
Personality board.<br />
3. Insert each auxiliary relay plug into the one of the two-pin sockets, beginning with AUX6,<br />
AUX7, AUX8, AUX9 and AUX10 on the Personality board. For wiring details, refer to the<br />
System Wiring Diagrams for model i10X page 10.<br />
Personality Board<br />
Relay Retaining<br />
Screws<br />
Optional Relays (5x)<br />
<strong>IntelliTouch</strong> <strong>Expansion</strong> <strong>Center</strong> Kit <strong>Installation</strong> <strong>Guide</strong>
Connecting the <strong>Expansion</strong> Unit to the Load/Power <strong>Center</strong><br />
To connect a 4-wire cable from the Load <strong>Center</strong> or Power <strong>Center</strong> to the Personality board in the<br />
<strong>Expansion</strong> enclosure:<br />
7<br />
1. CAUTION - Switch the main power off at the Load <strong>Center</strong> or Power <strong>Center</strong>.<br />
2. At the Load <strong>Center</strong> or Power <strong>Center</strong>, loosen the two access screws securing the Outdoor<br />
Control Panel. Fold down the control panel to access the Personality board.<br />
3. Insert one end of the 4-wire cable that connects the <strong>Expansion</strong> <strong>Center</strong> to the main Load<br />
center or Power <strong>Center</strong> into plastic grommet on the bottom of the enclosure and route the<br />
wire up through the low voltage raceway to the Personality board. Connect the wires to the<br />
COM port (see page 8, step 5, 6, and 7 for details).<br />
4. At the <strong>Expansion</strong> enclosure, Insert the 4-wire cable into plastic grommet on the bottom of<br />
the enclosure and route the wire up through the low voltage raceway to the Personality<br />
board. If necessary, for easier access to the raceway, remove the two screws securing the<br />
high voltage panel cover, and remove it from the <strong>Expansion</strong> enclosure.<br />
Outdoor Control Panel<br />
Access screw<br />
Access screw<br />
Cover-panel screw<br />
(Cover-panel not shown)<br />
Cover-panel screw<br />
Retaining screw<br />
Retaining screw<br />
Low voltage raceway<br />
Plastic grommet<br />
<strong>Expansion</strong> <strong>Center</strong><br />
<strong>IntelliTouch</strong> <strong>Expansion</strong> <strong>Center</strong> Kit <strong>Installation</strong> <strong>Guide</strong>
8<br />
5. Strip back the cable conductors ¼ inch. Insert the wires into the either of the COM PORTS<br />
(J7 and J8) screw terminals located on the left side of the Personality board. Secure the<br />
wires with the screws. Make sure to match the color-coding of the wires: GND = Black,<br />
Green = -DT, Yellow = +DT, and Red = +15 (see diagram below). For wiring details, refer to<br />
the Wiring Diagram for models i5x and i10x (page 10). Note: Multiple wires may be inserted<br />
into a single screw terminal.<br />
6. Close the <strong>Expansion</strong> enclosure Outdoor Control Panel and secure it with the two access<br />
screws.<br />
7. If removed, install the high voltage panel cover and secure it with the two retaining screws.<br />
Personality Board (Left-side)<br />
Note: COM Ports can also be used for<br />
connection to IntelliChlor and IntelliFlo<br />
Personality<br />
Board<br />
Feed each relay<br />
cable plug up<br />
through holes<br />
<strong>IntelliTouch</strong> <strong>Expansion</strong> <strong>Center</strong> Kit <strong>Installation</strong> <strong>Guide</strong>
9<br />
Connecting the <strong>Expansion</strong> <strong>Center</strong> Transformer<br />
To connect the <strong>Expansion</strong> <strong>Center</strong> transformer wire harness onto the Personality board:<br />
• Connect the transformer plug onto connector J2 on the right side of Personality board. The<br />
plug is keyed onto the pins so that the six wires point towards back of the board. From left to<br />
right the wire colors should be blue, orange, red. For the connector location, refer to the<br />
diagram shown below and the System Wiring Diagram (page 10).<br />
Note: The transformer terminals can be wired 115 VAC or 230 VAC. Refer to the System<br />
Wiring Diagram for models i5x and i10x (see page 10 for wiring connections).<br />
Affixing the System Wiring Diagram Label<br />
To affix the wiring diagram label on the <strong>Expansion</strong> <strong>Center</strong> inside front door:<br />
1. Open the <strong>Expansion</strong> <strong>Center</strong> front door.<br />
2. Peel the backing off the wiring diagram label.<br />
3. Position the label in middle of the inside of the front door. Apply even pressure on the surface<br />
of the label to secure in place.<br />
<strong>IntelliTouch</strong> <strong>Expansion</strong> <strong>Center</strong> Kit <strong>Installation</strong> <strong>Guide</strong>
10<br />
System Wiring Diagram<br />
(For models i5x and i10x)<br />
<strong>IntelliTouch</strong> <strong>Expansion</strong> <strong>Center</strong> Kit <strong>Installation</strong> <strong>Guide</strong>
11<br />
Glossary<br />
<strong>Expansion</strong> Kit: A kit that includes additional auxiliaries to an existing Personality Kit. Requires a<br />
Load <strong>Center</strong> for each <strong>Expansion</strong> Kit.<br />
Feature Circuits: Programmable circuits that may control relays and/or valve actuators. For details<br />
see the <strong>IntelliTouch</strong> Systems User’s <strong>Guide</strong> (P/N 520102)<br />
High Voltage Compartment: Large lower right compartment of Load <strong>Center</strong> for all high voltage<br />
wiring including circuit breakers, relays, and GFCI.<br />
Indoor Control Panel: This fourteen button remote controller with LCD (liquid crystal display) is<br />
wired to the Personality board in the Power/Load <strong>Center</strong>. The control panel can be wall mounted<br />
inside a house to control <strong>IntelliTouch</strong> Systems.<br />
iS4: Four function Spa-Side remote. Can be spa wall or deck mounted.<br />
iS10: Up to ten function spa-side remote with temperature changing capability. Can be spa wall or<br />
deck mounted.<br />
Load <strong>Center</strong>: Metal enclosure with power relays, transformer, and circuit breakers. The Load <strong>Center</strong><br />
is Installed prior to Personality Kit installation. Used for distributing power for controlling <strong>IntelliTouch</strong><br />
Systems. Also known as the “sub-panel.”<br />
Low Voltage Compartment: Top compartment of Load <strong>Center</strong> for all low voltage wiring.<br />
Low Voltage Raceway: Vertical space in the left side of Power/Load <strong>Center</strong> for low voltage cabling.<br />
MobileTouch Controller: Wireless controller for the <strong>IntelliTouch</strong> Systems with all the functionality of<br />
the Indoor Control Panel.<br />
Mud Box: Enclosure to provide mounting features for iS10 spa-side remote that is cast into gunite,<br />
concrete, or other spa wall/deck construction.<br />
Outdoor Control Panel: Control panel with flexible hinge installed in upper portion of Power/Load<br />
<strong>Center</strong> to control <strong>IntelliTouch</strong> systems.<br />
Personality Board: The circuit board mounted on top of the Outdoor Control Panel motherboard.<br />
The Personality board defines the system capabilities.<br />
Personality Kit: Set of parts to define the capability of a system; may include: Outdoor Control<br />
Panel, temperature sensors, actuators, control panel (Indoor or MobileTouch), additional relays,<br />
actuators.<br />
Power <strong>Center</strong>: Same as Load <strong>Center</strong> with the exception of the circuit breaker base.<br />
Relay Circuits: The circuits that control the relays on the Personality Board. Connectors on top<br />
edge of the circuit board.<br />
Terminal Connector: Removable connector that may attach to circuit board with multiple sockets<br />
(anywhere from 2 to 12) to receive wires from controllers and sensors; wires held by screw<br />
terminals; multiple wires of a small enough gauge (usually 22 AWG) may be coupled to a single<br />
socket of a terminal connector.<br />
Transceiver: Circuit board with attached antenna that can send and receive radio frequency<br />
(wireless) transmissions.<br />
<strong>IntelliTouch</strong> <strong>Expansion</strong> <strong>Center</strong> Kit <strong>Installation</strong> <strong>Guide</strong>
12<br />
Notes<br />
<strong>IntelliTouch</strong> <strong>Expansion</strong> <strong>Center</strong> Kit <strong>Installation</strong> <strong>Guide</strong>
P/N 520471 - Rev A